TiO2胶粒在铝合金表面的电泳沉积及所制薄膜的光催化性能研究

TiO₂ membranes were prepared on aluminum-alloy thin plates by electrophoretic deposition and dip coating in a colloid solution of TiO₂, respectively. The photocatalytic activity of TiO₂ membrane was compared using ethylene as reactant, and the crystal and morphological structure of the membrane were characterized by XRD and SEM. The results showed that a more compact membrane with high loading of TiO₂ but lower photocatalytic activity of unit TiO₂ mass was obtained by electrophoresis compared with dip coating method. The addition of polyethylene glycol (PEG) to the sol of TiO₂ could improve the specific photocatalytic activity (ethylene conversion per unit mass TiO₂ and unit area of membrane piece) of the electrophoresis-membrane prepared from the sol, but could not change the specific photocatalytic activity of the dip-coating membrane from the sol. The ethylene conversion on the electrophoresis membrane prepared from the sol containing PEG (50 g·L^-1) was 9 times of that on the dip coating membrane. The effect of PEG on the properties of electrophoresis-membrane of TiO₂ was attributed to the change of electrokinetic properties of sol. Addition of PEG decreased ζ potential value of the sol and the mobility of the sol particle, increased viscidity of the colloid, thus decreasing both the electrophoresis deposition velocity of colloid particles and the electroosmosis velocity of diffuse layer of colloid particles. These favored the formation of a low compact and porous membrane on the electrode in electric field, and thus increasing the availability of TiO₂ in photocatalytic process.     

表面活性剂辅助水热合成氧化钛纳米针溶胶

TiO₂ nanoneedles sol with particle size of 10～15 nanometer was synthesized by hydrothermal method using peroxo titanic acid as the precursor, cetyltrimethyl ammonium bromide(CTAB) as the surfactant. The product was characterized by XRD, TEM, HRTEM and selected area electron diffraction(SAED). The results show that the as-prepared products have high crystallinity and grow along the c-axis, with homogeneous morphology and good monodispersity. In addition, TiO₂ hydrosol possessed good photocatalytic activity for the photocatalytic degradation of methyl orange aqueous solution under the sunlight illumination.     

纳米二氧化钛粉末的溶胶-凝胶法合成及晶相转化

Nanosized TiO₂ powder with anatase and rutile structures was synthesized by a sol-gel method using TiCl₄ ethanol solution as a precursor.The grain size of TiO₂ powder was about 63nm after the precursor was calcined at 600℃ for 2 hours .The experimental techniques of XRD,TEM and Particle Distribution were used to characterize the synthesized specimens. Various special effects were investigated for their contribution to crystal structure and the size of TiO₂ powder .The formation of anatase as well as the rutile phase of TiO₂ was indicted from the XRD when the reaction temperature was above 30℃ and when the sol was irradiated by infrared rays .However, an anatase TiO₂ powder formed after the heat treatment of the dried gel in a temperature range from 300℃ to 500℃.Under the vacuum drying and with the calcined time below 3hours ,the anatase phase was gained .As well as with the increase of gelatinizing time, the anatase TiO₂ powder was obtained.     

锐钛矿型TiO2水溶胶的低温制备及其表征

Anatase titanium dioxide hydrosol was prepared at low temperature by a simple method. The title material was characterized by TEM, XRD, FTIR and BET, respectively. The photocatalytic activity of the as-prepared TiO₂ was evaluated by the degradation of methyl orange solution under sunlight and the photocatalytic oxidation of acetone in air. The results showed that the titanium dioxide hydrosol was composed of anatase phase with average grain size of about 7 nm, and the crystallinity became more perfect with the increase of temperature. The BET surface areas were more than 220 m²·g^-1 for these samples. It is found that the photocatalytic activity was much better for the higher heat processing temperature. Especially, the photocatalytic activity of the sample with a heat treatment of 110 ℃ was better than that of P25. In addition, TiO₂ hydrosol also possessed good photocatalytic activity under the sunlight illumination.     

微乳法制备纳米TiO2 /SiO2的结构及光催化研究

Nanosized TiO₂ and TiO₂/SiO₂ particles were prepared by hydrolysis of tetrabutyl titanate (TBOT) and tetraethyl orthosilicate (TEOS) in the TX-100 reverse microemulsion. These particles were characterized by TG-DSC, XRD, FTIR, TEM，N₂ adsorption-desorption. Their photocatalytic activity was tested by degradation of methyl orange. The result shows that TiO₂/SiO₂ nanoparticles are with a monodispersed spherical phase and a uniform size distribution，and TiO₂ particles are dispersed on the surface of SiO₂. The band for Ti-O-Si vibration in FTIR was observed, the Ti-O-Si bond increased the stability of anatase TiO₂, suppressed the phase transformation of titania from anatase to rutile. And due to the addition of SiO₂, the average size of titania decreased from 38 nm in pure TiO₂ to 5 nm in TiO₂/SiO₂. It was found, under UV light irradiation, TiO₂/SiO₂ particles showed higher activity than pure TiO₂, and TiO₂/SiO₂(1/1) particles showed the highest photocatalytic activity on the photocatalytic decomposition of methyl orange, which was influenced by crystal structure, particle size, crystallinity and Surface area Characteristics.     

电化学法制备高热稳定性锐钛矿型纳米TiO2

Titanium alkoxides were prepared by anodic dissolution of metallic titanium in absolute ethanol in the presence of HN(C₂H₅)₂*HCl (electro－conductive additives).The solution was directly hydrolyzed to prepare nanocrystalline of TiO₂ (about 10nm)by a sol－gel process.The precursor gels was calcined at T=450 ℃ and 720 ℃for 30 min,and nanocrystalline of TiO₂ (anatase) with high textural and thermal stability was obtained.FTIR,XRD,TEM,were used to characterize the structure of titanium alkoxides and nanocrystalline of TiO₂.The characteristics of nanocrystalline of TiO₂ was depended on the properties of titanium alkoxides.The Ti(OEt)₄ as a source of titanium yielded the best textural and thermal stability nanocrystalline of TiO₂.     

多重射流燃烧反应制备的TiO2/ SiO2纳米复合颗粒的形态和结构

TiO₂-SiO₂ nanocomposite particles were prepared in premixed H₂ / Air flame, and the morphology and structure of these nanocomposites were characterized by FTIR, XRD, TEM and HRTEM. The morphology of SiO₂ / TiO₂ nanocomposites was different from that of pure TiO₂ or SiO₂ nanoparticles, and the chemical bond of Ti-O-Si was found in the nanocomposites indicating that the TiO₂ / SiO₂ nanocomposites were not merely a physical mixture of TiO₂ and SiO₂. TiO₂ nanocrystalline grains with sizes of 1～2 nm were homogeneously dispersed in the amorphous SiO₂ matrix when TiCl₄ and SiCl₄ were mixed at molecular level in the flame. The particle size and rutile content decreased with increasing of SiO₂ molar ratio.     

有机体系中电合成纳米PbTiO3粉体及表征

The precursor PbTi(OCH₂CH₃)_6-y(acac)_y for the mixed oxide PbTiO₃was synthesized by electrochemical dissolution of Lead and Titanium with a 1∶2 electricity quality in ethanol and acetyl-acetone solution. Nano-sized PbTiO₃powder was prepared by drying and calcining the xerogel from a direct sol-gel hydrolyzation of the precursor solution under pH of 8.5. The FTIR, TG-DTA, XRD and TEM were employed to characterize the structure of the precursor and nano-sized PbTiO₃. The results showed that the optimized conditions for the preparation of nano-sized PbTiO₃ were the electrolysis of the Lead plate and Titanium plate at 50 ℃ and 40 ℃ respectively under 0.03mol·dm^-3Bu₄NBr solution. The nano-sized PbTiO₃prepared by electrolysis exhibited a dispersive structure with an average diameter of 10 to 15 nm.     

纳米尖晶石LixMn2O4的制备与电化学性能表征

Nano-spinel Li_xMn₂O₄(0.6 ≤x≤ 1.0) was synthesized by two steps of coprecipitation and calcination. The influences of calcination temperature, time and Li/Mn ratio on the crystal structure and the particle size of Li_xMn₂O₄ were investigated. It was shown that the higher the calcination temperature, the more complete the crystal structure, and the larger the particle size. Moreover, the influence of calcination time on the crystal structure was insignificant when it was more than 3h at 700℃. With the increase of x in Li_xMn₂O₄ in the range of 0.6～1.0, the d111 and lattice parameter a increased first and then decreased. The electrochemical properties of nano-spinel LiMn₂O₄ using as cathode material of lithium-ion battery were studied. The low discharge capacity might be due to the irreversible capacity loss brought by the large surface area and lattice vacancies of the nano-spinel.     

有机溶液中电化学制备纳米MgTiO3

In a cell without separating the cathode and anode spaces, the precursor MgTi(OCH₂CH₃)_(6-y)(acac)_y of the mixed oxide MgTiO₃ was directly synthesized by electrochemical dissolution of titanium for 4 hours and then of magnesium for 1 hour 40 minutes at the current of 0.2 A in ethanol and acetyl-acetone solution. The nano- MgTiO₃ powder was prepared by a direct sol-gel process of the electrolyte solution under pH≈8.5 followed by washing, drying in vacuum for 24 h, and calcination at 500 ℃ for 2 h. IR and Raman spectroscopy, XRD, and TEM were used to investigate the structure of nano-MgTiO₃ and its precursor. The result suggested that it was more appropriate to control the temperature between 35～40 ℃ and the concentration of conductive additive (Bu₄N)Br at 0.04 mol·L^-1. The xerogel with an average particle size of 12 nm and the nano-MgTiO₃ of 20 nm was thus obtained in a high purity.     

Cr2(WO4)3和Cr2(MoO4)3的负热膨胀特性研究

用液相反应-前驱物烧结法制备了Cr₂(WO₄)₃和Cr₂(MoO₄)₃粉体。298～1 073 K的原位粉末X射线衍射数据表明Cr₂(WO₄)₃和Cr₂(MoO₄)₃的晶胞体积随温度的升高而增大, 本征线热膨胀系数分别为(1.274±0.003)×10^-6 K^-1和(1.612±0.003)×10^-6 K^-1。用热膨胀仪研究了Cr₂(WO₄)₃和Cr₂(MoO₄)₃在静态空气中298～1 073 K范围内热膨胀行为，即开始表现为正热膨胀，随后在相转变点达到最大值，最后表现为负热膨胀，其负热膨胀系数分别为(-7.033±0.014)×10^-6 K^-1和(-9.282±0.019)×10^-6 K^-1。     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

Eu0.5RE0.5Fe0.5Mn0.5O3的57Fe Msosbauer谱研究

利用固相反应合成了Eu0.5RE0.5Fe0.5Mn0.5O3(RE=La,Pr,Nd,Sm,Eu,Gd,Tb,Dy,Ho,Er,Tm,Yb,Y)等化合物。测量了其XRD谱及57FeMssbauer谱。实验发现,随着RE原子序数的增加,样品的晶胞体积减小,Fe在化合物中处于Fe3+的高自旋状态,57Fe的四极裂矩与样品的畸变参数D成线性关系。     

Vibrational spectra of the peroxotantalates (NH4)3[Ta(O2)4], K3[Ta(O2)4], Rb3[Ta(O2)4] and Cs3[Ta(O2)4] and the crystal structure of Rb3[Ta(O2)4]

The compounds (NH₄)₃[Ta(O₂)₄], K₃[Ta(O₂)₄], Rb₃[Ta(O₂)₄] and Cs₃[Ta(O₂)₄] have been prepared and investigated by X-ray powder methods as well as Raman- and IR-spectroscopy. In the case of Rb₃[Ta(O₂)₄] the structure has been solved from single crystal data. It is shown that all these compounds are isotypic and crystallize in the K₃[Cr(O₂)₄] type (SG , No. 121). The infrared- and Raman spectra (recorded on powdered samples) are discussed with respect to the internal vibrations of the peroxo-group and the dodecahedral [Ta(O₂)₄]³⁻ ion. Symmetry coordinates for the [Ta(O₂)₄]³⁻ ion are given from which the vibrational modes of the O-O stretching vibrations of the O₂²⁻ groups, the Ta-O stretching vibrations and the Ta-O bending vibrations are deduced.     

Conversion of NO in NO/N2, NO/O2/N2, NO/C2H4/N2 and NO/C2H4/O2/N2 Systems by Dielectric Barrier Discharge Plasmas

An experimental study on the conversion of NO in the NO/N₂, NO/O₂/N₂, NO/C₂H₄/N₂ and NO/C₂H₄/O₂/N₂ systems has been carried out using dielectric barrier discharge (DBD) plasmas at atmospheric pressure. In the NO/N₂ system, NO decomposition to N₂ and O₂ is the dominating reaction; NO conversion to NO₂ is less significant. O₂ produced from NO decomposition was detected by an on-line mass spectrometer. With the increase of NO initial concentration, the concentration of O₂ produced decreases at 298 K, but slightly increases at 523 K. In the NO/O₂/N₂ system, NO is mainly oxidized to NO₂, but NO conversion becomes very low at 523 K and over 1.6% of O₂. In the NO/C₂H₄/N₂ system, NO is reduced to N₂ with about the same NO conversion as that in the NO/N₂ system but without NO₂ formation. In the NO/C₂H₄/O₂/N₂ system, the oxidation of NO to NO₂ is dramatically promoted. At 523 K, with the increase of the energy density, NO conversion increases rapidly first, and then almost stabilizes at 93–91% of NO conversion with 61–55% of NO₂ selectivity in the energy density range of 317–550 J L⁻¹. It finally decreases gradually at high energy density. A negligible amount of N₂O is formed in the above four systems. Of the four systems studied, NO conversion and NO₂ selectivity of the NO/C₂H₄/O₂/N₂ system are the highest, and NO/O₂/C₂H₄/N₂ system has the lowest electrical energy consumption per NO molecule converted.     

A Structural Investigation of La2(GeO4)O and Alkaline-Earth-Doped La9.33(GeO4)6O2

The structures of the oxyorthogermanate La₂(GeO₄)O and the apatite-structured La_9.33(GeO₄)₆O₂ have been refined from powder neutron diffraction data. La₂(GeO₄)O crystallizes in a monoclinic unit cell (P2₁/c) and is cation stoichiometric in contrast to previous reports. La_9.33(GeO₄)₆O₂ crystallizes in a hexagonal unit cell (P6₃/m) and the powder diffraction data show anisotropic peak broadening that is observed in electron diffraction patterns as incommensurate diffuse spots at hkq reciprocal planes (with q=1.6-1.7) and can be attributed to a correlated disorder in the “apatite channels”. This compound was doped up to a nominal composition close to M₂La₈(GeO₄)₆O₂ with M=Ca, Sr, Ba. The dopant ions preferentially occupy the 4f sites as the number of La vacancies decreases. The measured ionic conductivity of La_9.33(GeO₄)₆O₂ is about 3 orders of magnitude larger than for La₂(GeO₄)O at high temperatures and decreases with increasing dopant content from the highest value of about 0.16 S cm⁻¹ at 1160 K.     

g-C3N4/Bi2O2CO32D纳米片复合材料的制备及可见光催化性能研究

采用自组装和化学沉淀法分别制得两种可见光驱动复合材料石墨相氮化碳/碳酸氧铋(g-C_3N_4/Bi_2O_2CO_3).采用X射线衍射光谱(XRD),紫外可见光谱、扫描电镜(SEM)、N_2吸附、电化学阻抗谱(EIS)和X射线光电子能谱(XPS)等分析手段对制备的催化剂进行了表征.结果表明,制备方法对纳米复合材料的晶相、形态及光学性能没有影响,但是影响g-C_3N_4和Bi_2O_2CO_3之间的相互作用力,导致光生电子-空穴对的分离速率存在显著差异.以可见光驱动苯酚和罗丹明B的降解实验为探针反应检测催化剂的光催化性能.实验结果表明自组装法得到的异质结催化剂中相互作用力更强,催化效果最高.O_2-是罗丹明B降解反应的主要活性物种,染料的光敏化、Bi_2O_2CO_3与g-C_3N_4综合效应,导致光生载流子电荷分离效率更高.     

可见光响应的Co3(PO4)2/Ag3PO4纳米复合光催化剂的制备及表征

采用简单的化学偏聚法合成出Ag₃PO₄纳米颗粒、磷酸钴（Co₃（PO₄）₂,CoP）纳米片以及它们两者的纳米复合结构（CoP/Ag₃PO₄）,同时还比较了它们的可见光催化活性. 采用场发射扫描电镜（FESEM）、X 射线衍射（XRD）、紫外-可见（UV-Vis）吸收光谱以及光致发光谱等手段对其形貌、结构、光学以及可见光催化性能等进行表征. 结果表明,CoP/Ag₃PO₄复合纳米结构的可见光降解甲基橙（MO）的速率和循环稳定性均明显优于其它两种物质. 这表明CoP应该起着共催化剂的作用,它能够抑制光生电子与空穴之间的复合,并且提供大量高活性的光生空穴. 此外,我们还发现CoP/Ag₃PO₄降解另一种阳离子型染料——罗丹明B（RhB）的能力则远不如纯Ag₃PO₄,这可能是与光催化剂的表面性质发生改变有关,造成更低的RhB吸附能力. 本文提供了一种廉价制备高效可见光催化剂的新方法.     

Ni-P-Zn3(PO4)2(ZnSnO3、ZnSiO3)纳米复合化学镀层性质和组成的研究

研究了温度、时间、浓度等对Ａ３钢片上Ｎi-P-Zn3(PO4)2、Ni-P-ZnSnO3和Ｎi-P-ZiSiO3纳米复合合化学镀层外貌的影响,用扫描电子显微镜（ＳＥＭ）观察外貌、称重法测定厚度;通过１０％ＮaCl溶液、１％Ｈ２Ｓ气体加速腐蚀试验,１０％ＣuSO4溶液点滴试验等多种手段测定其耐腐蚀性能,用Ｘ－射线光电子谱（ＸＰＳ）及俄歇电子能谱（ＳＥＳ）测定其价态组成,结果表明：在最佳施镀条件下,可得光亮、致密、耐腐蚀性强于Ａ３钢、磷化膜及Ｎi-P镀层的纳米复合化学镀层,镀层的原子百分组成约为（％）：Ｎi-P-Zn3(PO4)2:Ni70.00,P12.47,Zn3(PO4)213.93,C3.6;Ni-P-ZnSnO3;Ni77.56,P10.00,ZnSnO39.84,C2.6;Ni-P-NiSiO3,Ni83.00,P10.96,ZnSi5.15,C0.89.     

Synthesis, crystal structure, infrared and Raman spectra of Sr4Cu3(AsO4)2(AsO3OH)4·3H2O and Ba2Cu4(AsO4)2(AsO3OH)3

The two new compounds, Sr₄Cu₃(AsO₄)₂(AsO₃OH)₄·3H₂O (1) and Ba₂Cu₄(AsO₄)₂(AsO₃OH)₃(2), were synthesized under hydrothermal conditions. They represent previously unknown structure types and are the first compounds synthesized in the systems SrO/BaO-CuO-As₂O₅-H₂O. Their crystal structures were determined by single-crystal X-ray diffraction [space group C2/c, a=18.536(4) Å, b=5.179(1) Å, c=24.898(5) Å, β=93.67(3)°, V=2344.0(8) Å³, Z=4 for 1; space group P4₂/n, a=7.775(1) Å, c=13.698(3) Å, V=828.1(2) Å³, Z=2 for 2]. The crystal structure of 1 is related to a group of compounds formed by Cu²⁺-(XO₄)³⁻ layers (X=P⁵⁺, As⁵⁺) linked by M cations (M=alkali, alkaline earth, Pb²⁺, or Ag⁺) and partly by hydrogen bonds. In 1, worth mentioning is the very short hydrogen bond length, D···A=2.477(3) Å. It is one of the examples of extremely short hydrogen bonds, where the donor and acceptor are crystallographically different. Compound 2 represents a layered structure consisting of Cu₂O₈ centrosymmetric dimers crosslinked by As1φ₄ tetrahedra, where φ is O or OH, which are interconnected by Ba, As2 and hydrogen bonds to form a three-dimensional network. The layers are formed by Cu₂O₈ centrosymmetric dimers of CuO₅ edge-sharing polyhedra, crosslinked by As1O₄ tetrahedra. Vibrational spectra (FTIR and Raman) of both compounds are described. The spectroscopic manifestation of the very short hydrogen bond in 1, and ABC-like spectra in 2 were discussed.