Effect of conversion of NO2 into no on the catalytic reduction of NO2 with C3H6 in excess O2

During the reduction of NO₂ by C₃H₆ in O₂ over alumina-supported Au, Rh and Pt it was found that three parallel reactions take place,i.e., reduction of NO₂ to N₂ and N₂O, partial decomposition of NO₂ to NO and oxidation of C₃H₆ to CO and CO₂. In the absence of C₃H₆, the NO₂→NO+O₂ reaction reaches a fast equilibrium on Rh and Pt but not on Au and γ-Al₂O₃. Addition of C₃H₆ to the NO₂+O₂ mixture leads to the formation of NO above equilibrium conversion levels.     

Catalytic reduction of nitrogen monoxide with propene over Nb/TiO2 mixed mechanically with Mn2O3

Selective catalytic reduction of nitrogen monoxide (NO) over a catalyst of mechanically mixed Nb/TiO₂ and Mn₂O₃ (Mn₂O₃+Nb/TiO₂) in an oxidizing atmosphere with propene (C₃H₆) was studied. The Mn₂O₃+Nb/TiO₂ catalyst showed high activity for the reduction of NO to N₂. The maximum conversion of NO to N₂ was observed at 200∼300°C, with about 80% reduction of NO to N₂. Mn₂O₃ enhanced the formation of NO₂ from NO and the activation of propene to react with NO₂ for reduction to N₂.     

(La0.8A0.2)MnO3 (A = Sr,K) perovskite catalysts for NO and C10H22 oxidation and selective reduction of NO by C10H22

In this work, we studied the catalytic activity of LaMnO₃ and (La_0.8A_0.2)MnO₃ (A = Sr, K) perovskite catalysts for oxidation of NO and C₁₀H₂₂ and selective reduction of NO by C₁₀H₂₂. The catalytic performances of these perovskites were compared with that of a 2 wt% Pt/SiO₂ catalyst. The La site substitution increased the catalytic properties for NO or C₁₀H₂₂ oxidation compared with the non-substituted LaMnO₃ sample. For the most efficient perovskite catalyst, (La_0.8Sr_0.2)MnO₃, the results showed the presence of two temperature domains for NO adsorption: (1) a domain corresponding to weakly adsorbed NO, desorbing at temperatures lower than 270 ℃ and (2) a second domain corresponding to NO adsorbed on the surface as nitrate species, desorbing at temperatures higher than 330 ℃. For the Sr-substituted perovskite, the maximum NO₂ yield of 80% was observed in the intermediate temperature domain (around 285 ℃). In the reactant mixture of NO/C₁₀H₂₂/O₂/H₂O/He, (La_0.8Sr_0.2)MnO₃ perovskite showed better performance than the 2 wt% Pt/SiO₂ catalyst： NO₂ yields reaching 50% and 36% at 290 and 370 ℃, respectively. This activity improvement was found to be because of atomic scale interactions between the A and B active sites, Sr²⁺ cation and Mn⁴⁺/Mn³⁺ redox couple. Thus, (La_0.8Sr_0.2)MnO₃ perovskite could be an alternative free noble metal catalyst for exhaust gas after treatment.     

Vapour-liquid equilibrium data for the systems C2H6 + N2, C2H4 + N2, C3H8 + N2, and C3H6 + N2

High pressure vapour-liquid equilibrium data for the C₂H₆ + N₂, C₂H₄ + N₂, C₃H₈ + N₂, and C₃H₆ + N₂ systems are presented. The data are obtained isothermally in the range from 200 K to 290 K. For each point of data, temperature, pressure and liquid and vapour phase mole fractions are measured.Values for the vapour phase mole fractions are calculated from the obtained pressure, temperature and liquid phase mole fractions. The calculated values are compared with the experimental results, and it is found that the average mean deviation between calculated and experimental mole fractions is less than 0.009 for the systems considered in this work.     

Ho(NO3)3(C2H5O2N)4·H2O的低温热容和热力学函数

合成了稀土(钬, Ho)-氨基酸(甘氨酸, C₂H₅O₂N)二元配合物Ho(NO₃)₃(C₂H₅O₂N)₄·H₂O, 并且通过化学分析、元素分析和红外(IR)光谱对配合物进行了表征. 用高精度全自动绝热量热仪, 测定了该配合物在80-390 K温度区间的定压摩尔热容(C_p,m). 利用实验测定的热容数据, 采用最小二乘法, 将热容曲线上热容峰以外的两段平滑区的摩尔热容对折合温度进行拟合, 建立了热容随折合温度变化的多项式方程. 根据热容与焓、熵的热力学关系,计算出了配合物在80-390 K温度区间内,每隔5 K,相对于298.15 K的摩尔热力学函数(H_T,m-H_298.15,m)和(S_T,m-S_298.15,m). 通过热容曲线分析, 计算出了350 K附近转变过程的焓变(Δ_trsH_m)和熵变(Δ_trsS_m). 用差示扫描量热法(DSC)测定了配合物的热稳定性.     

NO reduction with C3H8 on Co/Al2O3 catalyst. effect of O2 concentration

The selective catalytic reduction (SCR) of NO by propane in excess oxygen-containing gas mixture was studied on Co/Al₂O₃ catalyst. The oxygen concentration is very important for the reaction. The NO conversion to N₂ without oxygen is 3% at 800 K and when the O₂ concentration is raised up to 8% the NO conversion reaches its maximum value of 60% at 800 K. Characterization results by TPR and UV-Vis spectroscopy show that in the catalyst, species strongly interacting with tetrahedral and octahedral Co²⁺ ions in the support are present. This revised version was published online in June 2006 with corrections to the Cover Date.     

g-C_3N_4/CaTi_2O_5复合材料制备及其光催化性能

利用类石墨氮化碳(g-C_3N_4)和亚稳相钙钛氧化物(CaTi_2O_5)固相法制备C_3N_4/CaTi_2O_5复合材料。利用X射线衍射(XRD)、金相显微镜、扫描电子显微镜(SEM)及附带能谱分析仪(EDS)和N2吸附-脱附对样品的显微结构和比表面积进行检测分析,并用紫外-可见吸收光度计(UV-Vis)测试了样品的光吸收性能,研究C_3N_4与CaTi_2O_5物质的量之比(nC_3N_4/nCaTi_2O_5)对C_3N_4/CaTi_2O_5复合样品的物相结构和微观形貌的影响,同时考察C_3N_4/CaTi_2O_5复合样品在可见光照射下光催化降解罗丹明染料效果。实验结果表明:相比纯C_3N_4和CaTi_2O_5样品,C_3N_4/CaTi_2O_5复合样品在可见光下具有较高的光催化性能,随着nC_3N_4/nCaTi_2O_5增加,样品的光催化降解率随之增加而后降低,当nC_3N_4/nCaTi_2O_5=1∶1时,样品的光催化降解率达到最大值99.5%,并且循环重复利用5次后,样品的光催化剂降解率仍几乎保持不变。复合样品光催化性能提高主要归因于复合能级结构有效地抑制了电子和空穴复合所致。     

g-C3N4/CaTi2O5复合材料制备及其光催化性能

利用类石墨氮化碳（g-C₃N₄）和亚稳相钙钛氧化物（CaTi₂O₅）固相法制备C₃N₄/CaTi₂O₅复合材料。利用X射线衍射（XRD）、金相显微镜、扫描电子显微镜（SEM）及附带能谱分析仪（EDS）和N₂吸附-脱附对样品的显微结构和比表面积进行检测分析,并用紫外-可见吸收光度计（UV-Vis）测试了样品的光吸收性能,研究C₃N₄与CaTi₂O₅物质的量之比（n_C3N4/nCaTi₂O₅）对C₃N₄/CaTi₂O₅复合样品的物相结构和微观形貌的影响,同时考察C₃N₄/CaTi₂O₅复合样品在可见光照射下光催化降解罗丹明染料效果。实验结果表明：相比纯C₃N₄和CaTi₂O₅样品,C₃N₄/CaTi₂O₅复合样品在可见光下具有较高的光催化性能,随着n_C3N4/nCaTi₂O₅增加,样品的光催化降解率随之增加而后降低,当n_C3N4/nCaTi₂O₅=1：1时,样品的光催化降解率达到最大值99.5%,并且循环重复利用5次后,样品的光催化剂降解率仍几乎保持不变。复合样品光催化性能提高主要归因于复合能级结构有效地抑制了电子和空穴复合所致。     

The direct decomposition of NO over the La2CuO4 nanofiber catalyst

The NO catalytic direct decomposition was studied over La₂CuO₄ nanofibers, which were synthesized by using single walled carbon nanotubes (CNTs) as templates under hydrothermal condition. The composition and BET specific surface area of the La₂CuO₄ nanofiber were La₂Cu_0.88²⁺Cu_0.12⁺O_3.94 and 105.0 m²/g, respectively. 100% NO conversion (turnover frequency-(TOF): 0.17 g_NO/g_catalyst s) was obtained over such nanofiber catalyst at temperatures above 300 °C with the products being only N₂ and O₂. In 60 h on stream testing, either at 300 °C or at 800 °C, the nanofiber catalyst still showed high NO conversion efficiency (at 300 °C, 98%, TOF: 0.17 g_NO/g_catalyst s; at 800 °C, 96%, TOF: 0.16 g_NO/g_catalyst s). The O₂ and NO temperature programmed desorption (TPD) results indicated that the desorption of oxygen over the nanofibers occurred at 80-190 and 720-900 °C; while NO desorption happened at temperatures of 210-330 °C. NO and O₂ did not competitively adsorb on the nanofiber catalyst. For outstanding the advantage of the nanostate catalyst, the usual La₂CuO₄ bulk powder was also prepared and studied for comparison.     

Novel measurements of refractive index, density and mid-infrared integrated band strengths for solid O2, N2O and NO2:N2O4 mixtures

We present novel measurements of the refractive index, density and integrated band strengths of mid-infrared features of solid N₂O at 16 K and of NO₂ and N₂O₄ in two frozen NO₂:N₂O₄ mixtures deposited at 16 and 60 K. The refractive index and density measurements were performed also for frozen O₂ deposited at 16 K. In this case, the integrated band strength values could not be determined since O₂ is a homonuclear molecule and therefore its fundamental mode is not infrared active. The solid samples were analysed by infrared spectroscopy in the 8000÷800 cm⁻¹ range. The sample thickness was measured by the interference curve obtained using a He–Ne laser operating at 543 nm. The refractive index at this laser wavelength was obtained, by numerical methods, from the measured amplitude of the interference curve. The density values were obtained using the Lorentz–Lorenz relation. Integrated band strength values were then obtained by a linear fit of the integrated band intensities plotted versus column density values. The astrophysical relevance of these novel measurements is briefly discussed.     

富氧条件下Co/ZSM-5催化剂对C3H8选择还原NOx的性能

采用多种物理化学手段研究了在模拟的轻型柴油车尾气中不同Co担载量及Cu掺杂的Co/ZSM-5催化剂的Co组分分散状态、可还原性、NO吸附脱附性质对C₃H₈选择性催化还原NO_x性能的影响。结果表明,浸渍法制备的Co/ZSM-5催化剂上既有外表面上的Co³⁺和Co²⁺物种,也有孔内的Co²⁺离子。富氧条件下Co/ZSM-5催化剂上C₃H₈选择性催化还原NO_x的活性主要与ZSM-5载体孔外表面分散的CoO_x物种中的钴离子可还原能力和NO吸附脱附性能密切相关。Co/ZSM-5催化剂上适宜的Co担载量约为4.0wt%,低担载量时随Co担载量增加,表面CoO_x物种中钴离子可还原能力增强,C₃H₈选择性催化还原NO_x的低温转化活性增加;高担载量时,随Co担载量增加,单位Co离子的NO吸附量的减少以及催化剂表面活性中心数的减少,导致了Co/ZSM-5催化剂NO_x的转化率和催化剂比速率（k）的下降。孔外表面Co₃O₄晶体的存在使催化剂表面产生较强的NO吸附,并在高温时有利于C₃H₈的氧化燃烧,使C₃H₈选择性催化还原NO_x的活性降低。     

富氧条件下Co/ZSM-5催化剂对C_3H_8选择还原NO_x的性能

采用多种物理化学手段研究了在模拟的轻型柴油车尾气中不同Co担载量及Cu掺杂的Co/ZSM-5催化剂的Co组分分散状态、可还原性、NO吸附脱附性质对C3H8选择性催化还原NOx性能的影响。结果表明,浸渍法制备的Co/ZSM-5催化剂上既有外表面上的Co3+和Co2+物种,也有孔内的Co2+离子。富氧条件下Co/ZSM-5催化剂上C3H8选择性催化还原NOx的活性主要与ZSM-5载体孔外表面分散的CoOx物种中的钴离子可还原能力和NO吸附脱附性能密切相关。Co/ZSM-5催化剂上适宜的Co担载量约为4.0wt%,低担载量时随Co担载量增加,表面CoOx物种中钴离子可还原能力增强,C3H8选择性催化还原NOx的低温转化活性增加;高担载量时,随Co担载量增加,单位Co离子的NO吸附量的减少以及催化剂表面活性中心数的减少,导致了Co/ZSM-5催化剂NOx的转化率和催化剂比速率(k)的下降。孔外表面Co3O4晶体的存在使催化剂表面产生较强的NO吸附,并在高温时有利于C3H8的氧化燃烧,使C3H8选择性催化还原NOx的活性降低。     

Hydrocarbon Effects on the Promotion of Non-Thermal Plasma NO–NO2 Conversion

Kinetic modeling of non-thermal plasma chemistry is conducted to investigate hydrocarbon (CH₄, C₂H₄, C₃H₆, and C₃H₈) effects on the promotion of NO–NO₂ conversion. A reduced plasma chemistry model, in which radical reactions are selectively involved, is validated with experimental data. The higher reactivity of hydrocarbon additive with O radicals, which produces initial radicals, is requisite to initiate hydrocarbon decomposition, thus providing NO–NO₂ conversion. Initial radicals by plasma discharge induce continual hydrocarbon decomposition and this self-preserved reaction mechanism greatly contributes to the promotion of energy efficient NO–NO₂ conversion. Increase in the conversion extent by ethylene and propylene additives is substantial because of their stronger affinity with O radical. The primary routes of NO–NO₂ conversion process differed by hydrocarbon additives are presented and discussed with the assistance of sensitivity analysis.     

Catalytically Promoted NOx Sorption by ZrO2-Based Oxides

Metal promoted zirconia-based oxide sorbents, such as Pt–ZrO₂/Al₂O₃ for NO _x have been investigated. To clarify the role of the catalyst component, sorption of NO and NO₂ was compared using the samples with and without Pt. The catalytic oxidation of NO to NO₂ and successively to nitrate ions is an important role for the Pt catalyst. The experimental results indicate that a high-temperature calcination is essential to remove residual Cl from Pt–ZrO₂–Al₂O₃ prepared from H₂PtCl₆ in order to provide more active NO _x sorption sites. Of M–ZrO₂–Al₂O₃ samples investigated, ruthenium as well as Pt demonstrated relatively good performance as a catalyst component in the sorbent. The FT-IR spectra after sorption of NO and NO₂ demonstrated a strong band attributed to stored nitrate ions. The Pt catalyst was more resistant to sulfur poisoning than a base metal catalyst. However, the NO _x sorptive capacities of the Pt–ZrO₂/Al₂O₃ sorbents were expected to be deteriorated in dilute SO₂ as far as observed from FT-IR spectra.     

Infrared studies of the diatomic molecules O2, N2, NO and H2 adsorbed on Fe2O3

An infrared spectroscopic study of the diatomic molecules O₂, N₂, NO and H₂ adsorbed under different conditions on Fe₂O₃ has been performed.Complex patterns of absorption on both α-Fe₂O₃ and γ-Fe₂O₃ activated in O₂ at high temperature are assigned to vibrations of two different chemisorbed O₂ species.N₂ molecules do not interact with “oxygen rich” α-Fe₂O₃ surfaces, but give N₂O^? and N₂O₂^2? species when chemisorbed on evacuated surfaces.NO molecules give complex patterns of absorption, depending on the gas pressure. Three different types of nitrate structures can be identified, as well as NO, NO^? and cis-N₂O₂ chemisorbed species. Chemisorbed water molecules are formed by contact of H₂ with Fe₂O₃ surfaces even at room temperature.     

Reactions of C2(a 3πu) with CH4, C2H2, C2H4, C2H6, and O2 using multiphoton UV excimer laser photolysis

C₂(a ³π_u) disappearance rate constants of 1.44, 0.96, 0.0296, 0.0130 and < 10^?6(x10^?10cm³s^?1) are reported for reactions with C₂H₄, C₂H₂, O₂, C₂H₆, and CH₄, respectively at 298 K. C₂(a ³π_u) fragments are generated by multiphoton ArF excimer laser photodissociation at C₂H₂, and monitored by dye laser induced fluorescence. Arguments are presented which favor chemical reactions over the C₂(a ³π_u) → (X ¹σ⁺_g) quenching channel. C₂ + C₂H₂ represents the one possible exception to the reactive channel.     

Vibrational spectra of cyclooctatetraenyl alkali metal complexes [C8H8M2 (M = Na, K)]: A theoretical study

The cyclooctatetraenyl dianion (C₈H₈²⁻) π-conjugated system forms a stable complex system with alkali and some transition metals. The results of vibrational analysis for C₈H₈M₂ (M = Na, K) complexes were reported here. The geometries of C₈H₈M₂ (M = Na, K) were optimized using ab initio (HF, MP2, CCSD(T)) and DFT (B3LYP) methods with 6-311G** and 6-311++G** basis sets and the harmonic frequencies were obtained. To reproduce and compare with the experimental values the structurally similar molecules C₅H₅M (M = Na, K) and benzene were studied. The scale factors obtained from these systems were applied to predict the experimental frequencies of C₈H₈M₂ (M = Na, K). The force field and vibrational spectra are analyzed and the most probable assignments are proposed for all the fundamentals based on the potential energy distribution.     

Ionization gauge sensitivities of N2, O2, N2O, NO, NO2, NH3, CClF3 and CH3OH

A Bayard-Alpert (BA) gauge was used to determine apparent relative sensitivites S_rel,X for O₂, N₂O, NO, NO₂, NH₃, CClF₃ and CH₃OH from gauge calibration measurements in the range 1.3×10^–1 Pap1.3·10^–3Pa. Nitrogen was used as a calibration standard.     

N2O and NO2 Formation in the Disproportionation of no over Ion Exchanged Cu-ZSM-5 at Lower Temperature

NO₃-type and NO₂-type adsorbed species are formed on Cu-ZSM-5 together with adsorbed O species at 523 K in the decomposition of NO accompanied by the evolution of N2, N₂O, and NO₂. This revised version was published online in June 2006 with corrections to the Cover Date.     

Evidence for the distortion of C2H4 and C2H2 chemisorbed on W(100)

The adsorption of C₂H₄ on W(100) has been studied by ultraviolet photoelectron spectroscopy with hν = 21.22 eV. The spectrum measured after in initial saturation exposure at 80 K exhibits structure which correlates well with energy levels recently calculated by Demuth and Eastman (DE) for sp³ rehybridized C₂H₄. Dehydrogenation of the adsorbate, either by subsequent heating to 295 K or direct adsorption at 295 K, yields a spectrum which correlates with DE's calculation for sp² rehybridized C₂H₂. These results suggest that C₂H₄ and C₂H₂ may be distorted from their planar and linear structures respectively and that the CC bonds on these molecules are stretched by adsorption on W(100). Qualitative arguments suggest that the bonding site for both melecules is directly over a W atom and that the Dewar—Chatt model for πd bonding in organometallic compounds is applicable.