共查询到19条相似文献,搜索用时 93 毫秒
1.
SiC是新一代射频器件和功率器件的理想材料,电阻式物理气相传输法由于具有温度均匀性,成为生长大尺寸SiC单晶的有效方法。近年来,多孔石墨等的使用提高了SiC晶体的质量和产量,而关于其机理的研究却相对较少。本文使用数值模拟的方法系统研究了多孔石墨对SiC晶体生长的影响,并进行了晶体生长验证。模拟结果表明:多孔石墨的使用提高了原料区域的温度及温度均匀性,增大了坩埚内轴向温差,对减弱原料表层的重结晶也具有一定作用;在生长腔内,多孔石墨改善了物质流动在整个生长过程中的稳定性,提高了生长区域的C/Si比,有助于减小相变发生概率,同时多孔石墨对晶体界面也起到改善作用。晶体生长结果实际验证了多孔石墨在提高传质均匀性、降低相变发生率和改善晶体外形上的作用。本文结果对于理解多孔石墨的作用机理以及改善SiC晶体生长条件具有实际意义。 相似文献
2.
3.
4.
5.
6.
7.
蓝宝石晶体热性能的各向异性对SAPMAC法晶体生长的影响 总被引:1,自引:1,他引:0
采用有限元法对冷心放肩微量提拉法蓝宝石晶体生长过程中晶体内的温度、应力分布进行了模拟计算,结合实验结果讨论了蓝宝石晶体热性能的各向异性对晶体生长的影响.研究结果表明,对于冷心放肩微量提拉蓝宝石晶体生长系统,较大的轴向热导率有利于提高晶体的生长速率和界面稳定性,而稍大的径向热导率则有利于保持微凸的生长界面.晶体内的热应力受径向热膨胀系数的影响显著,随着径向热膨胀系数的增大而增大,最大热应力总是出现在籽晶与新生晶体的界面区域.在实验中选α轴为结晶取向,成功生长出了直径达230mm、高质量蓝宝石晶体. 相似文献
8.
9.
10.
11.
大尺寸低缺陷碳化硅(SiC)单晶体是功率器件和射频(RF)器件的重要基础材料,物理气相传输(physical vapor transport, PVT)法是目前生长大尺寸SiC单晶体的主要方法。获得大尺寸高品质晶体的核心是通过调节组分、温度、压力实现气相组分在晶体生长界面均匀定向结晶,同时尽可能减小晶体的热应力。本文对电阻加热式8英寸(1英寸=2.54 cm)碳化硅大尺寸晶体生长系统展开热场设计研究。首先建立描述碳化硅原料受热分解热质输运及其多孔结构演变、系统热输运的物理和数学模型,进而使用数值模拟方法研究加热器位置、加热器功率和辐射孔径对温度分布的影响及其规律,并优化热场结构。数值模拟结果显示,通过优化散热孔形状、保温棉的结构等设计参数,电阻加热式大尺寸晶体生长系统在晶锭厚度变化、多孔介质原料消耗的情况下均能达到较低的晶体横向温度梯度和较高的纵向温度梯度。 相似文献
12.
Velocity of crystal growth of SiC in a process of solution growth was studied on the basis of a global model of heat and mass transfer in conjunction with a phase diagram of the Si–C system. The growth rate was estimated by flux of carbon to a seed crystal. The results of calculation showed that growth velocity was increased when temperature of a seed crystal was increased. The temperature dependence of growth velocity was mainly determined by the phase diagram of the Si–C system, although the flow pattern was slightly modified by changing temperature distribution in the furnace. 相似文献
13.
14.
A new SiC growth system using the dual-directional sublimation method was investigated in this study. Induction heating and thermal conditions were computed and analyzed by using a global simulation model, and then the values of growth rate and shear stress in a growing crystal were calculated and compared with those in a conventional system. The results showed that the growth rate of SiC single crystals can be increased by twofold by using the dual-directional sublimation method with little increase in electrical power consumption and that thermal stresses can be reduced due to no constraint of the crucible lid and low temperature gradient in crystals. 相似文献
15.
16.
17.
碳化硅(SiC)作为第三代半导体材料,不仅禁带宽度较大,还兼具热导率高、饱和电子漂移速率高、抗辐射性能强、热稳定性和化学稳定性好等优良特性,在高温、高频、高功率电力电子器件和射频器件中有很好的应用潜力。高质量、大尺寸、低成本SiC单晶衬底的制备是实现SiC器件大规模应用的前提。受技术与工艺水平限制,目前SiC单晶衬底供应仍面临缺陷密度高、成品率低和成本高等问题。高温溶液生长(high temperature solution growth, HTSG)法生长SiC单晶具有晶体结晶质量高、易扩径、易实现p型掺杂等独特的优势,有望成为大规模量产SiC单晶的主要方法之一,目前该方法的主流技术模式是顶部籽晶溶液生长(top seeded solution growth, TSSG)法。本文首先回顾总结了TSSG法生长SiC单晶的发展历程,接着介绍和分析了该方法的基本原理和生长过程,然后从晶体生长热力学和动力学两方面总结了该方法的研究进展,并归纳了该方法的优势,最后分析了TSSG法生长SiC单晶技术在未来的研究重点和发展方向。 相似文献
18.
SiC单晶生长热力学和动力学的研究 总被引:3,自引:2,他引:1
升华法生长大直径碳化硅(SiC)单晶一直是近年来国内外研究的重点,本文对Si-C系中的Si,Si2,Si3,C,C2,C3,C4,C5,SiC,Si2C,SiC2等气相物种的热力学平衡过程进行了研究,发现SiC生长体系中的主要物种为Si,Si2C,SiC2.生长初期Si的分压较高,从而SiC生长为富硅生长模式.对外加气体进行研究发现,氩气为最好的外加气体,它既可以有效地抑制Si物质流传输,又可以减缓扩散系数随温度升高而递减的趋势.建立了简单一维传输模型,对三个主要物种的动力学输运过程进行了研究,计算得到了两个温度梯度下的主要物种的物质流密度. 相似文献
19.
To effectively design a large furnace for producing large-size AlN crystals, a fully coupled compressible flow solver was developed to study the sublimation and mass transport processes in AlN crystal growth. Compressible effect, buoyancy effects, flow coupling between aluminum gas and nitrogen gas, and Stefan effect are included. Two sets of experimental data were used to validate the present solver. Simulation results showed that the distributions of Al and N2 partial pressures are opposite along the axial direction due to constant total pressure and Stefan effect, with the Al and nitrogen partial pressures being highest at the source and seed crystals positions, respectively. The distributions of species inside the growth chamber are obviously two-dimensional, which can curve a flat crystal surface. Simulation results also showed that AlN crystal growth rate can be increased by reducing total pressure or by increasing seed temperature or by increasing source-seed temperature difference. High nitrogen pressure causes decrease in growth rate, but it is beneficial for obtaining uniform growth rate in the radial direction. Results of simulation also showed that there is an optimized temperature difference (40 °C) in the present furnace for obtaining good homogeneity of growth rate. 相似文献