谱元法研究桁架结构的振动带隙特性

采用谱元法研究了桁架周期结构的带隙特性.从杆和梁的运动方程出发,推导出与频率相关的插值函数,得到了杆单元和梁单元的动力学刚度矩阵.在频域下将铰结构考虑为一个谱单元,并推导出铰单元的动力学刚度矩阵.将杆/梁单元和铰单元加以整合得到整体结构的动力学刚度阵,进而建立整体结构的运动方程.通过求解整体结构的动力学方程,获得结构的频域响应,进而研究结构的带隙特性.本文将谱元法求解得到的固有频率结果与有限元法进行了对比,分析了单胞数量和材料的变化对结构带隙特性的影响,拓展了谱元法的应用领域.     

力-压电混合弹性超材料梁的带隙调节特性

为实现宽带低频减振,本文将力振子和串联负电容的压电分流振子分别置于基体上下两侧,设计了混合弹性超材料梁。基于传递矩阵法建立了理论模型,用于计算混合弹性超材料梁的频散关系和动态有效参数,通过有限元法进行了验证。分别采用理论方法和数值方法研究了电路元件参数对混合弹性超材料梁的带隙和振动衰减特性的调节机理,通过与单振子超材料的带隙对比,分析了两种振子间的相互影响。结果表明：电路元件参数主要影响压电分流振子产生的带隙的位置、宽度及带隙内的振动衰减程度;两种振子的带隙重叠区域不一定为通带;两种振子会因为负动态有效刚度范围靠近而相互影响。本研究将为此类超材料的设计提供参考依据。     

风力机叶片非线性挥舞分析

将风力机叶片简化为绕轮毂旋转的变截面Euler-Bernoulli悬臂梁,基于Greenberg公式给出非线性气动力,建立叶片挥舞振动非线性控制方程.由于变截面梁的弯曲刚度和线密度是沿梁轴线变化的函数,无法给出模态函数解析式,论文提出使用假设模态法计算的模态函数,作为基函数对控制方程进行Galerkin截断,通过将挥舞振动分解为静态位移和动态扰动合成,对其进行动态响应分析,同时讨论了叶轮转速、风速和旋转位置对振动特性的影响.研究表明:(1)叶轮转速对叶片挥舞特性影响显著,风速和叶片转角对振动特性影响很小.(2)静态位移随风速增加而增大,大体上成线性关系,气动阻尼随风速增加而减小.(3)风速较低时,非线性挥舞振动表现为衰减振动,随着风速增加,振动由衰减振动演化为周期运动,再由周期运动演化为拟周期运动.     

低频振动隔离和能量采集双功能超材料

振动隔离和能量采集一体化是一种能够将有害振动隔离并转化为电能收集利用的动力学机制. 本文从局域共振超材料存在低频带隙特性出发, 研究了振动隔离和能量采集双功能超材料的动力学行为. 通过在球型磁腔内放置固接了感应线圈的球摆构成具有能量采集功能的球摆型谐振器, 并将其周期性的放置在基体梁中, 可以将带隙频率范围内的振动聚集在谐振器内, 以实现振动隔离和能量采集双功能. 建立了横向激励下双功能超材料梁的动力学方程, 应用Bloch's定理得到超材料的能带结构, 通过有限元仿真验证了理论模型和研究方法. 研究了不同参数下超材料梁的带隙特性. 进一步将一维拓展到二维, 研究了二维双功能超材料板的振动隔离和能量采集性能. 最后, 设计并建造了振动隔离和能量采集一体化双功能超材料动力学实验平台, 解析、数值和实验结果表明, 在局域共振带隙的频率范围内, 超材料梁主体的振动明显被抑制, 与此同时, 振动被局限在谐振器中, 使采集到的电压达到了最大值. 通过对附加谐振器和没有附加谐振器的能带结构和幅频响应的对比, 发现球摆型谐振器的加入可以在低频范围内形成了一个局域共振带隙, 有效提高了超材料梁在低频处的振动隔离和能量采集性能.      

圆管型局域共振声子晶体三维构型振动带隙研究

采用多重多级子结构方法计算具有一定刚度的圆管型局域共振声子晶体三维构型振动带隙特性。考察包裹方向对带隙特性的影响,并对第一带隙上下边界点的单胞振动形式进行分析。结果表明,两种包裹形式都可以得到较低较宽的第一带隙,并且带隙特性相似,因而其周期结构都可以大幅减弱带隙范围内弹性波的传播。但两种构型带隙上下边界点对应振动形式不同,此外带隙特性还受单胞尺寸的影响。通过给定评价指标得到相关材料参数与带隙特性关系的相图,由此分析包裹层材料属性对带隙特性的影响。     

基于能量准则的梁振动多模态主动控制的LQR法

选用以结构振动能量和控制信号能量作为控制目标函数的LQR算法,在单对压电元件进行梁振动主动控制的基础上,使用多对压电元件进行主动控制．运用该算法对压电层合梁的振动控制进行了分析计算．数值算例表明该方法能够有效地控制多阶模态并减小控制能量的消耗．由此,进一步验证了以结构振动能量和控制信号能量作为控制目标函数的LQR算法的正确性。     

具有非线性支撑和弹性边界约束的轴向载荷梁结构动力学行为研究

弹性梁结构作为一种基本单元被广泛于建筑、航空、航天、船舶等工程领域. 为有效降低弹性梁结构的振动水平, 深刻理解其振动特性、动力学行为显得尤为重要. 本文建立了具有非线性支撑和弹性边界约束的轴向载荷梁结构动力学分析模型, 并采用伽辽金截断法预报梁结构的动力学响应. 在伽辽金截断法的求解过程中, 选取具有弹性边界约束的轴向载荷梁结构的模态振型函数作为伽辽金截断法的试函数与权函数. 首先, 研究截断数对伽辽金截断法稳定性的影响, 并采用谐波平衡法研究伽辽金截断法的可靠性. 在此基础上, 研究谐波激励扫频方向、非线性支撑参数对具有非线性支撑和弹性边界约束的轴向载荷梁结构动力学响应的影响规律. 研究结果表明, 具有非线性支撑和弹性边界约束的轴向载荷梁结构的动力学响应具有初值敏感性且非线性支撑参数对梁结构动力学响应的影响显著. 相关非线性支撑参数使得梁结构出现复杂动力学行为. 合适的非线性支撑参数能够抑制具有非线性支撑和弹性边界约束的轴向载荷梁结构的复杂动力学行为并对梁结构边界处的减振具有有益效果.      

斜拉桥主梁振动对拉索阻尼器减振效果的影响

应用拉索索端阻尼器是大跨度斜拉桥拉索减振的主要措施之一. 将主梁、索与阻尼器组合起来作为一个振动体系,通过理论分析与试验研究相结合的方法初步研究了主梁振动对拉索附加阻尼器减振效果的影响. 建立了由索、梁和Kelvin阻尼器组成的简化理论模型; 设计了索、梁和阻尼器组合系统的简化力学试验模型; 详细研究了主梁振动对拉索附加阻尼器减振效果的影响. 理论与试验分析结果表明: 对于容易发生索、梁耦合振动的拉索,主梁振动明显降低拉索附加阻尼器的减振效果;在大跨度斜拉桥拉索的减振设计中,需考虑主梁参与振动的影响.      

金字塔点阵圆筒结构轴向弹性波传递特性研究

点阵结构的周期和多孔特征使其相较于普通的实体结构具有轻质、耐冲击、减振降噪和高比强度等优势, 在航空航天和船舰等领域具有十分广泛的应用前景. 本文以金字塔点阵圆筒结构为对象, 根据单胞的宽、高和阵列的个数等独立的结构参数进行参数化建模, 并利用商用有限元软件计算了点阵圆筒结构轴向振动特性. 通过无量纲手段针对归一化频率和相对带宽, 系统研究了单胞的宽、高以及杆件直径等关键参数对减振效果的影响. 根据参数分析的结果, 设计了一种具有低频宽带减振性能的金字塔点阵圆筒结构. 使用增材制造技术制作了样件, 并进行了振动测试实验, 结果表明, 实验和有限元模拟的结果基本一致, 在500~1500 Hz范围内, 结构表现出明显的减振效果, 平均的衰减强度达到了50 dB左右.      

基于谱元法的空间刚架动力学特性分析

以空间刚架结构为研究对象,应用谱元法研究其动力学特性,依次推导出杆、轴和铁木辛柯梁的动力学刚度阵,进而得到空间刚架的动力学刚度阵和频域响应的理论方程,拓展了谱元法应用范围。编程计算获得空间刚架的固有频率和点的谐响应曲线,与有限元分析相比较,进一步得到载荷下的瞬态响应。研究表明,谱元法在刚架结构的动力学特性分析中,比有限元方法高效高精度,更适宜解决中高频振动问题。     

变截面多稳态梁结构减振吸能分析与优化设计

基于多稳态梁结构具有吸能且可重复使用的特点,本文研究包含变截面多稳态梁的单胞结构及其周期性排布的减振吸能效应及其优化设计方法。对多稳态结构进行考虑几何非线性的位移加载/卸载有限元仿真,根据其载荷-位移曲线分析多稳态结构的减振吸能原理,并研究串联与并联周期性排布形式对结构整体吸能特性的影响规律。研究基于多参数调控的变截面梁结构形状表征方法,根据多稳态结构储能特点建立变截面多稳态单胞结构的结构优化模型,通过求解优化问题获得总质量不变条件下最优变截面梁结构形状。进一步地通过对优化结果的有限元分析验证优化的有效性,并对结构进行瞬态冲击荷载下动响应分析,证明多稳态结构的冲击保护作用。     

Optimum design of band-gap beam structures

The design of band-gap structures receives increasing attention for many applications in mitigation of undesirable vibration and noise emission levels. A band-gap structure usually consists of a periodic distribution of elastic materials or segments, where the propagation of waves is impeded or significantly suppressed for a range of external excitation frequencies. Maximization of the band-gap is therefore an obvious objective for optimum design. This problem is sometimes formulated by optimizing a parameterized design model which assumes multiple periodicity in the design. However, it is shown in the present paper that such an a priori assumption is not necessary since, in general, just the maximization of the gap between two consecutive natural frequencies leads to significant design periodicity.The aim of this paper is to maximize frequency gaps by shape optimization of transversely vibrating Bernoulli–Euler beams subjected to free, standing wave vibration or forced, time-harmonic wave propagation, and to study the associated creation of periodicity of the optimized beam designs. The beams are assumed to have variable cross-sectional area, given total volume and length, and to be made of a single, linearly elastic material without damping. Numerical results are presented for different combinations of classical boundary conditions, prescribed orders of the upper and lower natural frequencies of maximized natural frequency gaps, and a given minimum constraint value for the beam cross-sectional area.To study the band-gap for travelling waves, a repeated inner segment of the optimized beams is analyzed using Floquet theory and the waveguide finite element (WFE) method. Finally, the frequency response is computed for the optimized beams when these are subjected to an external time-harmonic loading with different excitation frequencies, in order to investigate the attenuation levels in prescribed frequency band-gaps. The results demonstrate that there is almost perfect correlation between the band-gap size/location of the emerging band structure and the size/location of the corresponding natural frequency gap in the finite structure.     

A Gradient-Based Optimization Method for the Design of Layered Phononic Band-Gap Materials

Phononic materials with specific band-gap characteristics at desired frequency ranges are in great demand for vibration and noise isolation, elastic wave filters, and acoustic devices.The attenuation coefficient curve depicts both the frequency range of band gap and the attenuation of elastic wave, where the frequency ranges corresponding to the none-zero attenuation coefficients are band gaps. Therefore, the band-gap characteristics can be achieved through maximizing the attenuation coefficient at the corresponding frequency or within the corresponding frequency range. Because the attenuation coefficient curve is not smooth in the frequency domain,the gradient-based optimization methods cannot be directly used in the design optimization of phononic band-gap materials to achieve the maximum attenuation within the desired frequency range. To overcome this difficulty, the objective of maximizing the attenuation coefficient is transformed into maximizing its Cosine, and in this way, the objective function is smoothed and becomes differentiable. Based on this objective function, a novel gradient-based optimization approach is proposed to open the band gap at a prescribed frequency range and to further maximize the attenuation efficiency of the elastic wave at a specific frequency or within a prescribed frequency range. Numerical results demonstrate the effectiveness of the proposed gradient-based optimization method for enhancing the wave attenuation properties.     

考虑可制造性约束的声子晶体多目标拓扑优化

对声子晶体进行拓扑优化可得到具有目标带隙特性的声子晶体结构, 在减振、隔声等领域具有潜在应用价值. 然而, 优化结果常会出现孤立材料单元而导致的制造困难问题. 针对该问题, 本文提出协同考虑带隙性能和可制造性约束的二维多相声子晶体多目标拓扑优化方法. 以在特定频率段带隙最宽和结构质量最小为优化目标, 在对微结构进行连通性分析的基础上, 引入考虑可制造性因素的附加约束, 并利用有限元法和具有精英选择策略的非支配排序遗传算法对该优化模型进行数值求解. 通过数值算例验证了本文模型及方法的合理性和有效性. 结果表明, 附加可制造性约束的拓扑优化模型可有效避免二维声子晶体构型中出现孤立材料单元的情况, 优化结果在满足带隙性能预期指标的同时也可兼顾到实际可制造性要求. 与仅仅考虑带隙性能的单目标优化结果相比, 本文提出的同时兼顾带隙性能和可制造因素的多目标优化模型可以针对实际应用和制造条件, 实现不同目标间的平衡, 具有显著优势和良好的应用前景.      

Modeling and analysis of piezoelectric beam with periodically variable cross-sections for vibration energy harvesting

A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigated by the generalized differential quadrature rule (GDQR) method. The GDQR method is also used to calculate the forced vibration response of the beam and voltage of each piezoelectric layer when the beam is subject to a sinusoidal base excitation. Results obtained from the analytical method are compared with those obtained from the finite element simulation with ANSYS, and good agreement is found. The voltage output of this periodic beam over its first band gap is calculated and compared with the voltage output of the uniform piezoelectric beam. It is concluded that this periodic beam has three advantages over the uniform piezoelectric beam, i.e., generating more voltage outputs over a wide frequency range, absorbing vibration, and being less weight.     

分布振子复合板的模态阻尼及多点激励下阻尼减振相关性

分布阻尼振子可拓宽结构减振频带,因此可将振子分布于板中以形成复合板（简称“分布振子复合板”）,进而实现较宽的减振频带．对于多点支撑处受到宽频非一致激励（例如在不同激励点处的激励频率、幅值与相位有差异）的分布振子复合板,目前还缺乏有效简便的优化控制指标．在作者之前的研究中,针对含分布振子的梁推导了基于模态应变能的模态阻尼计算理论,讨论了模态阻尼与单点激励下梁的减振效果的相关性,并应用于宽频减振设计优化．本文进一步将模态阻尼计算理论推广到分布振子复合板,并将研究从梁的单点激励扩展到板的多点非一致激励下的阻尼减振相关性．首先,在利用模态应变能法推导得到分布振子复合板的模态阻尼计算公式后,从理论上讨论了不同边界条件与模态阶次对计算结果的影响,以及计算理论的适用性．而后,进一步通过有限元参数分析了边界条件、频率比、模态阶次与质量比的影响．最后,通过算例分析了无振子板或分布振子复合板在四个激励点具有多种幅值与相位组合情况下的稳态响应．结果表明,推导的模态阻尼计算公式可正确预测不同边界条件下的模态阻尼,且理论预测的模态阻尼与基板的稳态平均加速度减小率、稳态峰值应变能减小率均有较高的相关性．     

Modified shooting approach to the non-linear periodic forced response of isotropic/composite curved beams

Large amplitude periodic forced vibration of curved beams under periodic excitation is investigated using a three-noded beam element. The element is based on the higher-order shear deformation theory satisfying interlayer continuity of displacements and transverse shear stress, and top-bottom conditions on the latter. The periodic responses are obtained using shooting technique coupled with Newmark time marching and arc length continuation algorithm developed. The second order governing differential equations of motion are solved without transforming to the first order differential equations thereby resulting in a computationally more efficient algorithm. The effects of excitation amplitude, support conditions and beam curvature on the frequency versus response amplitude relation are highlighted. The typical frequency response curves for isotropic and cross-ply laminated curved beams are presented. Phenomenon of strong modal interactions is observed.     

局部约束阻尼开口柱壳的减振分析及优化

为了缩减开口柱壳结构的振动,本文基于Lagrange方程以及Sanders薄壳理论建立了局部约束阻尼开口柱壳的动力学模型,分析了粘弹性单元分段数和厚度、阻尼单元占空比以及约束层敷设角和厚度对结构前三阶模态损耗因子和固有频率的影响,得到了各参数对结构振动特性的影响规律.并以前三阶损耗因子为目标,应用NSGA-Ⅱ遗传算法对...     

Vibration band gap properties of periodic Mindlin plate structure using the spectral element method

In this paper, vibration band gap properties of periodic Mindlin plate structure with two simply supported opposite edges are studied using the spectral element method (SEM). Based on the Mindlin plate theory (MPT), the spectral Mindlin plate stiffness matrix is deduced. The spectral equation of the whole periodic structure is further established. Frequency responses are calculated by the spectral equations to illustrate band gap properties. Compared with the results based on the classic plate theory (CPT), the effects of the shear and rotary inertia on the band gap properties are analyzed. The results are also compared with those calculated by the finite element method (FEM). It can be observed that the SEM is more accurate in high frequency ranges. Furthermore, the influences of the material properties and structure dimension on the band gap behaviors are investigated.