界面压入法测定涂层结合强度的实验研究与理论分析

采用具有新颖性的涂层压入仪，在涂层与基体之间的界面压入，可测得压入过程中载荷与压入深度的关系曲线和界面开裂的临界载荷Ｐｗ，此值可反映涂层结合强度。界面压入法适合于评价高结合强度的涂层。根据能量守恒和转化原理，并结合Ｇｒｉｆｉｔｈ处理裂纹问题的思路，可得到结合应力表达式。在具体处理上采用数值计算与实验相结合的方法来近似处理，由此可得到结合应力值。     

材料动态强度直接测量的磁压剪实验技术及应用

提出一种用于直接测量动载荷下材料强度的新方法,即磁驱动压剪联合加载实验技术。从理论和数值计算上分析了压/剪联合作用下材料的应力偏量与屈服强度关系,计算斜波加载下压/剪联合作用时应力偏量与屈服强度的时空演化特性,给出材料强度数值的计算方法。并基于自行研制的强脉冲电流装置和10 T准静态磁场发生器,利用多点双光源外差位移干涉仪(dual laser heterodyne velocimetry, DLHV),开展磁压剪实验对2种铝样品的动态强度进行测量,得到不同加载压力下铝样品的强度。结果表明:磁驱动压/剪联合加载技术为材料的高压强度直接测量提供了一种新途径,是可靠的实验技术。     

围压状态下的混凝土本构模型

利用已有不同围压下的混凝土三向压缩试验, 分析研究不同围压条件对混凝土强度和应力-应变关系的影响。试验表明, 把混凝土简单视为脆性材料的观点并不符合实际情况, 塑性特征也是混凝土材料主要力学特征。由热力学定律出发, 本文提出了多次方形式的屈服函数和与围压状态相关联的损伤标准化函数, 提出了考虑围压状态的混凝土本构模型。试验结果与数值计算比较表明, 该本构关系可以很好地描述混凝土在不同围压状态下的力学损伤发展和脆-塑性转换力学特征, 也可以描述拉伸作用下的应力-应变关系, 具有一定的普遍意义。     

航空用芳纶纸蜂窝各向异性行为研究

采用Arcan加载装置对航空用芳纶纸蜂窝试件进行一系列面外压剪复合加载实验,以此研究材料各向异性行为。实验结果表明:随着面内方向角增加,芳纶纸蜂窝面内等效剪切模量、等效剪切强度显著减小,实验屈服面显著扩张,材料表现出明显的各向异性。基于实验结果,确定了测试蜂窝面内等效剪切模量、等效剪切强度上下限值及其比值关系,并与理论值进行比较。一个适用于各向异性材料的屈服准则与实验屈服面进行比较,比较结果表明:屈服准则能大致描述蜂窝各向异性屈服行为。     

仪器柔度标定误差对两种压入测试方法的精度影响

针对目前最具代表性的两种压入测试方法:Oliver-Pharr方法和Ma方法,通过有限元数值模拟分析了仪器柔度标定误差对测试精度的影响.结果表明仪器柔度的标定精度直接影响压入测试结果的准确度,尤其是当材料较软且压入深度较大时更为显著;对同一材料,压入载荷越大,由仪器柔度标定误差引入的压入测试结果误差越大;在同一压入深度下,针对不同材料,由仪器柔度标定误差引入的压入测试结果误差差别不大;就测试方法而言,Ma方法具有比Oliver-Pharr方法更高的精度和更低的仪器柔度敏感性.     

线性强化材料厚壁圆筒的统一极限分析

运用统一强度理论对承受内压的拉压屈服强度不同的线性强化材料的厚壁圆筒进行了极限载荷分析，得到了适用于多种材料的厚壁圆筒极限载荷的统一解析式．     

拉压异性材料含受压圆孔大平板的极限分析

探讨了广义双剪应力强度理论在平面应力状态下的屈服轨迹及其方程式,并用于拉压异性材料圆孔受内压的极限分析,得到了与拉压比有关的弹性极限内压力,弹塑性区的应力、塑性内压力与弹塑性分界半径之间的关系、塑性区的最大半径和最大内压力,所得极值均高于用莫尔强度理论分析的结果。     

???????????????????????????????

基于27种合金钢与铝合金的机械、力学性能，分析对比了3种理论估算疲劳极限方法的估 算结果，发现3种方法中只有两种方法能够比较精确地估算材料的疲劳极限; 当引 入强度系数和应变硬化指数与常规机械与力学性能的关系之后，这两种方法都可借助材料的 常规机械与力学性能估算疲劳极限，估算过程中的限制性条件``高强度钢'应予取消.     

闭孔泡沫铝的高温局部压入力学响应

通过不同形状(平头和半球头)的压头在不同温度下对闭孔泡沫铝材料进行塑性压入实验,研究不同温度下闭孔泡沫铝的压入变形模式及载荷响应特性。并基于闭孔泡沫铝在高温下的准静态塑性压入载荷响应的实验结果,结合多种分析方法,(如量纲分析和有限元计算等),探索既考虑温度影响也包含压入深度影响的预测闭孔泡沫铝平头和半球头压入力学响应的经验公式。结果表明,本文得到的两种压头情况下的经验公式都能够较好地预测闭孔泡沫铝在不同温度下的压入力学响应。     

金属材料的强度与应力-应变关系的球压入测试方法

压入法获取材料单轴应力-应变关系和抗拉强度对服役结构完整性评价有重要的基础意义.假定材料均匀连续、各向同性、应力应变关系符合Hollomon律,基于能量等效假定,即代表性体积单元(representativevolume element, RVE)的vonMises等效和有效变形域内能量中值等效假定,本文提出了关联材料载荷、深度、球压头直径和Hollomon律的四参数半解析球压入(semi-analyticalspherical indentation,SSI)模型.通过球压入载荷-深度试验关系获得材料的应力-应变关系和抗拉强度.考虑压入过程中的损伤效应,针对金属材料提出了用于球压入测试的材料弹性模量修正模型.对11种延性金属材料完成了球压入试验,采用本文提出的球压入试验方法测到的弹性模量、应力-应变关系和抗拉强度与单轴拉伸试验结果吻合良好.      

一种基于直接计算高阶奇异积分的断裂力学双边界积分方程分析法

相对于有限元法,边界单元法在求解断裂问题上有着独特的优势,现有的边界单元法中主要有子区域法和双边界积分方程法.采用一种改进的双边界积分方程法求解二维、三维断裂问题的应力强度因子,对非裂纹边界采用传统的位移边界积分方程,只需对裂纹面中的一面采用面力边界积分方程,并以裂纹间断位移为未知量直接用于计算应力强度因子.采用一种高阶奇异积分的直接法计算面力边界积分方程中的超强奇异积分;对于裂纹尖端单元,提供了三种不同形式的间断位移插值函数,采用两点公式计算应力强度因子.给出了多个具体的算例,与现存的精确解或参考解对比,可得到高精度的计算结果.      

汶川地震诱发文家沟巨型滑坡 碎屑流基本特征及成因机制初步分析


2008年5月12日,汶川M80地震在四川省绵竹市清平乡文家沟内诱发一巨型滑坡。通过现场调查得知,滑坡前后缘高差455m,厚度20～30m,滑面为基岩层面,初始方量2750×107m3。滑体在运动中转化为碎屑流。滑坡-碎屑流总的水平运动距离为4022m,垂直运动距离为1443m,遗留的堆积物体积达5×107m3。滑坡距映秀—北川断裂仅36km,位于其下盘,地震烈度达XI度。滑坡导致文家沟中48人遇害,并形成一条完整的地震次生地质灾害链。初步分析表明滑坡启动速度快,滑坡向碎屑流转化过程明显、地点明确。碎屑流运动过程复杂,伴有强烈的“气垫效应”和“前缘气浪冲击效应”。作者认为,文家沟滑坡的高启动速度是长持时强烈地震动作用的结果,与山体的猛烈碰撞是导致滑体解体并转化为碎屑流的原因。     

Preface: Orbits around asteroid

One of the core issues in modern celestial mechanics is the orbital dynamics in the near-regime gravitational field of as- teroids, which provides deep insights into the mathematical nature of a class of nonlinear systems, and plays as a critical basis for in situ explorations of different science goals. Lots of efforts have been made to reveal the characteristics of orbital motion in the vicinity of asteroids, and to improve the skills of asteroid research in methodology.     

Effet de l'anisotropie élastique cristalline sur la distribution des facteurs de Schmid à la surface des polycristauxInfluence of crystalline elasticity anisotropy on Schmid factor distribution at the free surface of polycrystals

Experimental studies of the plasticity mechanisms of polycrystals are usually based on the Schmid factor distribution supposing crystalline elasticity isotropy. A numerical evaluation of the effect of crystalline elasticity anisotropy on the apparent Schmid factor distribution at the free surface of polycrystals is presented. Cubic elasticity is considered. Order II stresses (averaged on all grains with the same crystallographic orientation) as well as variations between averages computed on grains with the same crystallographic orientation but with different neighbour grains are computed. The Finite Element Method is used. Commonly studied metals presenting an increasing anisotropy degree are considered (aluminium, nickel, austenite, copper). Concerning order II stresses in strongly anisotropic metals, the apparent Schmid factor distribution is drifted towards small Schmid factor values (the maximum Schmid factor is equal to 0.43 instead of 0.5) and the slip activation order between characteristic orientations of the crystallographic standard triangle is modified. The computed square deviations of the stresses averaged on grains with the same crystallographic orientation but with different neighbour grains are a bit higher than the second order ones (inter-orientation scatter). Our numerical evaluations agree quantitatively with several observations and measures of the literature concerning stress and strain distribution in copper and austenite polycrystals submitted to low amplitude loadings. Hopefully, the given apparent Schmid factor distributions could help to better understand the observations of the plasticity mechanisms taking place at the free surface of polycrystals. To cite this article: M. Sauzay, C. R. Mecanique 334 (2006).     

Nonlinear behavior of matrix-inclusion composites under high confining pressure: application to concrete and mortar

This paper is devoted to a micromechanics-based simulation of the response of concrete to hydrostatic and oedometric compressions. Concrete is described as a composite made up of a cement matrix in which rigid inclusions are embedded. The focus is put on the role of the interface between matrix and inclusion which represent the interfacial transition zone (ITZ). A plastic behavior is considered for both the matrix and the interfaces. The effective response of the composite is derived from the modified secant method adapted to the situation of imperfect interfaces. To cite this article: T.H. Le et al., C. R. Mecanique 336 (2008).     

Dynamics and Breakup of Viscoelastic Liquids (A Review)

The phenomena of hydrodynamic breakup of liquid jets, drops, films, bridges, and filaments are reviewed for liquids with viscoelastic properties. The reasons for breakup are capillary instabilities, collisions with rigid obstacles, and other forms of dynamic action. The relationship between the properties of the liquids and the features of the breakup process is discussed.     

Flow stability analysis and excitation using pulsating jets

Classical flow stability applied to transition from laminar to turbulent flow may also describe the behavior of vorticity fluctuations created by a pulsating jet placed along a solid boundary. A numerical laminar flow experiment involving a pulsating jet placed along the surface of a duct with flow separation downstream, resulted in eliminating most part of the separated flow region. Applying the same approach to a turbulent flow, it was possible to develop a turbulent stability flow formulation and apply successfully turbulent pulsating jet flow separation control. To cite this article: D. Skamnakis, K. Papailiou, C. R. Mecanique 333 (2005).