双轴应力状态下正交异性动态光弹性应力——光性定律研究

基于静态下Ｈｙｅｒ和Ｌｉｕ表述的正交异性应力－光性定律，在前文中，提出了正交异性光弹性复合材料的动态应力－光性定律并证明了其在单轴应力状态下的正确性。本文旨在进一步考察在双轴应力状态下正交异性动态应力－光性定律的适用性，采用的方法是对纤维增强光弹性复合材料制作的平板模型施加冲击荷载，加载方向与材料纤维方向分别成０°、９０°及４５°角，同时进行正交异性动态光弹性实验和动态应变测量，另外，对该模型进行相应的各向异性介质时域边界元计算。把动态应变测量推算出的应力分量以及时域边界元计算出的应力分量分别代入正交异性动态应力－光性定律，得到随时间变化的双折射条纹级数历程，将其与正交异性动态光弹性实验的结果进行比较。实验及计算结果表明，在三个加载方向下，由这三种方法得到的双折射条纹级数历程均吻合良好，从而证明了前文提出的正交异性动态应力－光性定律在双轴应力状态下的正确性。     

各向异性介质波动问题的时域边界元法及实验验证

对前已建立的各向异性介质波动问题的时域边界元计算模型进行了实验验证．用单向纤维增强光弹性复合材料模拟正交异性介质，用冲击加载，加载方向与纤维方向分别成0°，90°及45°角度，进行了正交异性动态光弹性实验及动态应变测量，并同时对该模型进行了时城边界元计算．将时域边界元方法计算出的应力分量代入正交异性动态光弹性的动态应力-光性定律，得到双折射条纹级数随时间的变化曲线，将其与动态光弹性实验的结果进行比较；此外，由动态电测获得的应变响应曲线推算出应力时程；与时城边界元计算出的应为响应曲线也进行了比较．两种情况下，时域边界元的计算成果均与实验成果吻合较好，从而证明该各向异性介质波动问题的时域边界元计算模型具有较好的精度及稳定性，可用于各向异性介质的动态问题特别是波传播问题的分析研究．     

正交异性光弹性应力分离的边界元法

本文对平面正交各向异性复合材料模型引入正应力线性和及边界上正应力线性和流的概念,提出从应力相容方程出发.用边界元法计算正交异性光弹性模型内任一点的正应力线性和位的方法,再与正交异性光弹性法中所给出的应力同的关系结合,即可进行正交异性光弹性应力的分离.最后,对边界元方法的精度进行了讨论.     

冲击作用下含孔洞纤维增强复合材料平板的动力学实验与数值研究

作为复合材料动力学实验与数值研究的应用实例 ,实验研究采用正交异性动态光弹性方法 ,数值分析运用各向异性介质的时域边界元方法。纤维增强光弹性复合材料平板被用来模拟含孔洞的正交异性半无限域 ,用小口径步枪施加与纤维方向成 0及 90两个方向的冲击载荷 ,在正交异性动态光弹性实验中记录了应力波在孔洞周围的传播、反射与绕射过程 ,此过程被进一步转换成应力分量的变化时程 ,并与相应的时域边界元方法的数值分析结果进行了比较。     

复合材料光弹性分析的近似方法

本文提出了一种用于光弹性复合材料的简化应变——光学定律。按照这一简化定律。模型材料的主应变差和主应变方向只要利用光弹性实验测出的等差线与等倾线即可求得。些是一种正交异性光弹性分析的近似方法,这一方法所得结果与实验数据比较,最大误差在10％左右。由于采用简化应变——光学定律使得正交异性光弹性分析工作大为简便,因此它是一种适合于工程应用的近似方法。     

复合材料光弹性分析的工程方法

本文在推导均衡光弹性复合材料应力(应变)—光定律的基础上,导出了均衡光弹性复合材料的近似应变—光定律。然后加以推广,提出适用于一般光弹性复合材料的近似应变—光定律.精度分析及实验验证表明:作为工程计算,在采用本文推荐的参数时,光弹性复合材料可视作各向同性材料进行光弹性分析。     

动态光弹性方法的主应力分离的研究

本文提出了动态光弹性、动态焦散线实验方法同边界元法结合的混合法，并用这种方法解决了动态光弹性主应力分离的问题，首先对现有的多火花高速摄影系统进行了改造，在动态实验过程中，成功地得到了不同瞬时的清晰的动态光弹性的等差线条纹和动态焦散线系列图像，这样，便可提取不同瞬时的边界应力值、全场主应力差值及边界上的外载。继而提出用Ｌａｐｌａｃｅ变换域上的边界元法来求解在冲击载荷作用下二维弹性模型全场的主应力和。最后，以受冲击载荷作用的圆盘为例，进行实验及边界元法计算，得到了分离的主应力场。     

一种动光弹模型材料的制作方法及其应用

基于#618环氧树脂、甲基六氢苯酐、促进剂DMP-30、环氧树脂消泡剂四种原料,提出制作光弹性模型的新配方和新方法,并利用单轴压缩实验、电测法和动态光弹法分别测定了制作的光弹模型的动态力学参数。新方法工艺简单,制作周期短,对人体无害。制作的光弹模型初始应力小,表面光洁,质地均匀,透光性好,光学灵敏度高,具有良好的机械加工和切削性能。通过三点弯曲梁冲击实验,得到了清晰的光弹等差条纹图像,验证了该配方和方法制作的模型可以应用于动态光弹性实验。     

确定应力强度因子的光弹性法与焦散线法

以光弹性法及焦散线法的基本原理为基础,对两种方法在确定应力强度因子方面进行了比较。发现对于纯I型裂纹问题,光弹性法的精度低于焦散线法的精度;对于I－Ⅱ混合型裂纹问题,就张开型应力强度因子而言,光弹性法的精度低于焦散线法的精度,而就滑移型应力强度因子而言,光弹性法的精度高于焦散线法的精度。     

平面应变各向异性本构关系及在应力波传播模拟中的应用

为了研究平面应变条件下各向异性材料中应力波传播的特点,利用各向异性弹性Hooke定律、 Tsai-Hill屈服准则、经典塑性流动理论,引入修正的物态方程计及高压下的体积压缩非线性,建立了平面应 变条件下正交各向异性复合材料的弹塑性本构关系,并且分析了二维问题中材料变形引起的主轴旋转及客 观应力率修正问题。最后采用动态显式有限元方法自行编写程序模拟某种纤维增强复合材料碰撞过程中平 面应力波的传播,模拟结果显示,在平面应变条件下应力波在该材料的传播过程中表现出明显的二维效应、各 向异性特点及弹塑性特点。     

The constitutive equations for mixed hardening orthotropic material

IntroductionAyieldingcriterionandtheassociatedflowtheorywereproposedbyHill[1]forinitiallyorthotropicmetalsin 1 948,whichareusedbroadly .AquadraticformofstressesisusedastheplasticpotentialthatisindependentofhydrostaticstressinHillplasticitytheory .Butcompressedbyhydrostaticstress,considerabledeformationwillbeproducedinorthotropicmaterials.Inthecaseofcyclicloading ,duetoBauschingereffect,thekinematichardeningcannotbeneglected .Inthispaper,kinematichardeningandproportionalhardeningareconsidered…     

Damage analysis and dynamic response of elasto-plastic laminated composite shallow spherical shell under low velocity impact

Based on the elasto-plastic mechanics, the damage analysis and dynamic response of an elasto-plastic laminated composite shallow spherical shell under low velocity impact are carried out in this paper. Firstly, a yielding criterion related to spherical tensor of stress is proposed to model the mixed hardening orthotropic material, and accordingly an incremental elasto-plastic damage constitutive relation for the laminated shallow spherical shell is founded when a strain-based Hashin failure criterion is applied to assess the damage initiation and propagation. Secondly, using the presented constitutive relations and the classical nonlinear shell theory, a series of incremental nonlinear motion equations of orthotropic moderately thick laminated shallow spherical shell are obtained. The questions are solved by using the orthogonal collocation point method, Newmark method and iterative method synthetically. Finally, a modified elasto-plastic contact law is developed to determine the normal contact force and the effect of damage, geometrical parameters, elasto-plastic contact and boundary conditions on the contact force and the dynamic response of the structure under low velocity impact are investigated.     

Dynamic stress intensity factor for cracked functionally graded orthotropic medium under time-harmonic loading

Dynamic stress intensity factor for a Griffith crack in functionally graded orthotropic materials under time-harmonic loading is investigated in the present paper. By using the Fourier transform and defining the jumps of displacement components across the crack surface as the unknown functions, two pairs of dual integral equations are derived. To solve the dual integral equations, the jumps of the displacement components across the crack surface are expanded in a series of Jacobi polynomial. Numerical examples are provided to show the effects of material properties and the crack configuration on the dynamic stress intensity factors of the functionally graded orthotropic materials with a Griffith crack.     

A stress-optic law for photoelastic analysis of orthotropic composites

The feasibility for utilizing transparent filament-resin composites for photoelastic stress analysis was investigated. Satisfactory photoelastic stress patterns were demonstrated in simple models with undirectional and bidirectional fiber orientations. A stress-optic law was formulated, based on the concept that the birefringence components contributed by each component of plane stress are combined according to a Mohr circle of birefringence. Applying this concept, the difference of the physical and optical principal directions was accounted for, and a general method of photoelastic solution for the plane-stress problem in orthotropic sheets was developed. The method of analysis is little more complex than the well-known procedures for isotropic materials, but at least three experimental measurements are required to characterize the optical response of the material to plane stress. Partial confirmation of the proposed stress-optic law was obtained by comparison of the theory to limited experimental data obtained in uniaxial-stress samples. It remains to establish a more positive verification by experiments in a variety of biaxial-stress conditions.     

The Thermoviscoelastoplastic Axisymmetric Stress–Strain State of Laminated Flexible Orthotropic Shells

A technique is proposed to determine the thermoviscoelastoplastic axisymmetric stress–strain state of laminated shells made of isotropic and orthotropic materials. The paper deals with processes of shell loading such that both instantaneous elastoplastic and creep strains occur in isotropic materials and elastic and creep strains in orthotropic materials. The technique is developed within the framework of the Kirchhoff–Love hypotheses for a stack of layers with the use of the equations of the geometrically nonlinear theory of shells in a quadratic approximation. The deformation of isotropic materials is described by the equations of the theory of deformation along slightly curved trajectories, while the deformation of orthotropic materials is described by Hooke's law with additional terms allowing for creep. A numerical example is given     

A study on yield and flow of orthotropic materials

On the assumption that the yield criterion of orthotropic materials is isomorphic with Huber-Mises criterion of isotropic materials, we put forward a dimensionless stress yield criterion, and obtained the associated plastic flow law. Using experimental stress-strain curves in various simple stress states, generalized effective stress-strain formulae may be derived correspondingly in various forms.     

Photo-orthotropic-elasticity

A method of producing transparent model materials for photo-orthotropic-elastic studies is presented. This material fabricated from glass fibers and a modified polyester matrix exhibits continuous relatively smooth fringe patterns which are linearly related to the state of stress. As such, the heterogenous material can be treated as a homogenous medium with orthotropic properties. Three photoelastic constantsf _L ,f _T andf _LT are necessary to describe the photoelastic response of the orthotropic materials to a general state of stress. Methods are established for predicting these photoelastic constants from the properties of the constituents. These methods are based on stress proportioning between the fibers and the matrix and upon the linear summation of the retardation from each constituent. The relations derived forf _L ,f _T andf _LT were verified experimentally and found to be in close agreement with measured values. A stress-optic law is derived on the basis of stress partitioning between the two constituents in a unidirectionally fiber-reinforced laminate. The adequacy of this stress-optic relation is confirmed by experimental verification. Comparison of this stress-optic relation with the expression advanced by Pih and Knight shows the validity of their initial concepts but the inadequacy of their partitioning functions. Detailed comparison of the stress-optic law with the analog relation proposed by Sampson shows excellent agreement. Indeed, the use of Sampson's stress-optic law is recommended and the law based on stress partitioning is to be considered as a fundamental theoretical proof of the Sampson relation. Finally, the applicability of Sampson's stress-optic law to bidirectionally reinforced materials was confirmed with a thorough experimental verification.     

Stress Concentration in an Orthotropic Plate with a Circular Hole under Dynamic Loading

The paper sets forth a photoelastic method for the determination of the dynamic stress concentration factor near a hole in an orthotropic plate. The stress distribution at the periphery of a circular hole is analyzed. The stress concentration factors for orthotropic and isotropic plates under dynamic and statical loading are compared     

正交各向异性材料的弹塑性损伤本构关系

基于弹塑性力学和损伤理论,建立了一个与应力球张量有关的正交各向异性材料的混合硬化屈服准则,该准则无量纲化后与各向同性材料的Mises准则同构,在此基础上,进而建立了混合硬化正交各向异性材料的增量型弹塑性损伤本构方程,并以具局部损伤的正交各向异性矩形薄板为例,采用Galerkin法和迭代法,对其弹塑性屈曲问题进行了分析,讨论了局部损伤对正交各向异性矩形薄板弹塑性屈曲临界应力的影响.      

Elasto-plastic postbuckling of damaged orthotropic plates

Based on the elasto-plastic mechanics and continuum damage theory, a yield criterion related to spherical tensor of stress is proposed to describe the mixed hardening of damaged orthotropic materials. Its dimensionless form is isomorphic with the Mises criterion for isotropic materials. Furthermore, the incremental elasto-plastic damage constitutive equations and damage evolution equations are established. Based on the classical nonlinear plate theory, the incremental nonlinear equilibrium equations of orthotropic thin plates considering damage effect are obtained, and solved with the finite difference and iteration methods. In the numerical examples, the effects of damage evolution and initial deflection on the elasto-plastic postbuckling of orthotropic plates are discussed in detail.