集簇式刚性连接组合梁桥的力学性能分析

为了研究任意荷载作用下集簇式刚性连接工字钢-混组合简支梁桥的应力和位移分布,首先将组合梁桥的三维结构简化为层合的二维弹性力学平面应力问题,分别求得各层简支梁的弹性力学解,然后用集中力替代集簇式刚性连接件对结构的作用力,根据梁桥表面的受力条件以及界面处位移和应力的衔接条件,确定待定未知量,从而得到组合梁桥的应力和位移分布函数.与有限元结果比较显示了该数值解具有很高的精度,参数化分析揭示了集簇式刚性连接组合梁桥的力学特点并且提出了簇钉间距的合理范围,研究结果为新型组合梁桥的工程设计提供了科学的理论依据.     

一维六方准晶弹性层合悬臂梁的解析解

本文利用一维六方准晶的平面本构关系,以及简化为平面问题的物理方程,在悬臂梁的弹性应力解的基础上,假设准晶层和弹性层的应力分布,求出了各自的位移表达式,再利用层间连续条件和放松的边界条件,推导出一维六方准晶层合悬臂梁仅在自由端受集中力作用下声子场和相位子场的位移解析解,为研究准晶涂层材料的力学性质提供参考。     

双材料叠合简支梁受均布载荷作用时的解析解

采用弹性力学的应力函数法,分析了上表面受均布载荷作用的上下层弹性模量和高度不同的双层叠合简支梁,对简支端提出了两种等效边界条件,得到了相应的两种解析解。运用有限元分析软件ANSYS,对不同组合的钢-铝双层叠合简支梁进行了数值计算,并与解析解进行了比较。结果表明:两种等效边界条件仅对弯曲正应力和位移有影响,对挤压应力和切应力没有影响;两种解析解的相对误差在1.2%以内;当跨高比超过6时,最大应力的解析解与有限元解的误差在4.4%以内;上下层对调后,两层中的应力基本不变;当上下层之间有摩擦时,弯曲正应力的外侧值大于内侧值,上、下层的中性层都由相应的几何中面向接触面偏移。     

集簇式组合梁桥振动特性的弹性力学解

基于二维弹性力学理论,研究了集簇式组合梁桥的自由振动特性。将组合梁桥等效为二维的层合梁模型,分别建立了各单层梁的自由振动微分方程,求得了简支边界条件下各层梁的弹性力学解。假定集簇式剪力件是刚性连接件,用待定集中力代替其提供的水平剪力,根据组合梁上、下表面的边界条件和层间应力、位移的协调关系,得到了简支组合梁桥自由振动特性的精确解析解,通过数值计算分析了簇钉间距对组合梁桥固有频率的影响。研究结果表明:理论结果与有限元ABAQUS解具有较好的一致性,最大误差仅为2.3%;组合梁桥的固有频率随着簇钉间距的减小而增大,当簇钉间距较小时,频率变化趋势不明显。其结果可为组合梁桥的合理设计提供参考。     

均布荷载作用下功能梯度简支梁弯曲的解析解

利用应力函数半逆解法,研究了均布载荷作用下、材料属性在厚度上任意变化的功能梯度简支梁弯曲的解析解,给出了各向应力应变与位移的解析显式表达式.首先根据平面应力状态的基本方程,得出了功能梯度梁的应力函数应满足的偏微分方程,并根据应力边界条件得出了各应力分布的表达式;进而根据功能梯度材料的本构方程和位移边界条件,得出了应变和位移的分布.最后,通过将本文的解退化到均质各向同性梁并与经典弹性解比较,证明了本文理论的正确性,并求解了材料组分呈幂律分布的功能梯度梁的应力和位移分布,分析了上下表层材料的弹性模量比λ与组分材料体积分数指数n对应力和位移分布的影响.     

平面弹性力学问题的离散元法

根据离散元的基本原理,基于变形体的理论提出了适用于平面弹性力学问题的界面位移、应变和应力模式,建立了求解平面弹性力学问题的离散元方程和相应的迭代求解方法.通过界面位移可以简洁地将位移和力的边界条件引入离散系统的控制方程,也可以方便地求解节点位移.数值算例表明,与具有相同网格的有限元结果相比,离散元能同时给出精度相对较高的应力解和精度相当的位移解.     

含固支端梁的解析解

采用弹性力学的应力函数法求含固支端梁的应力和位移时,无法严格满足固支端的实际边界条件,需要采用简化的固支边界条件。本文对已有的简化固支边界条件进行了改进,基于新的简化固支边界条件,推导出了四种含固支端梁的应力和位移的解析解,并进行了相应的数值计算,对几种固支边界条件进行了讨论。由本文方法得到的上表面受均布载荷作用悬臂梁的位移u和v的解析解与有限元解的最大误差分别为3.0%和1.0%,两端固支梁的应力σx的解析解与有限元解的最大误差为5.3%。通过理论与数值结果的比较表明,本文改进的固支边界条件是对固支端一种很好的简化。     

非理想界面弹性层/压电柱结构中SH波的传播特性

研究了各向同性弹性层与压电柱之间非理想连接时沿周向传播的SH波的频散特性.弹性层表面力学自由;弹性层与压电柱之间应力连续、位移间断.通过求解控制方程,将问题的解用Bessel函数表示,利用界面条件和边界条件得到频散方程,然后对其进行数值求解,分析了界面性态、材料常数和几何尺寸对SH波传播特性的影响.     

热黏弹性梁拟静态弯曲问题的解析分析

基于平面应力假设和热黏弹性材料的积分型本构关系,建立了以位移分量为未知量的热黏弹性梁静动力学分析的二维数学模型。针对拟静态弯曲问题,首先,在Laplace变换域,引入位移势函数,将控制方程解耦;其次,根据给定的平面温度场和边界条件,采用分离变量法,引入热应力函数,得到了热黏弹性梁的热应力分布;最后,利用Laplace逆变换,获得了热黏弹性梁拟静态弯曲热应力响应的解析解,考察了热载荷作用下几何、黏弹性等参数对梁应力和位移的影响。     

机械荷载与热荷载共同作用下变厚度梁的热弹性力学解

本文研究了两端简支变厚度梁受机械荷载与热荷载共同作用下的热弹性力学解.温度场用调和级数展开,通过求解热传导方程可首先确定温度沿梁厚度方向的非线性分布情况.从二维热弹性力学理论的基本方程出发,导出满足控制微分方程和两端简支边界条件的位移函数的一般解,对上下表面的边界方程作傅立叶正弦级数展开确定待定系数,数值结果与商业有限元软件ANSYS进行了比较,显示出很高的精度.本文方法可直接应用于对应力和位移分析要求较高的工程问题,如航空航天和微型机械的设计.     

一种基于直接计算高阶奇异积分的断裂力学双边界积分方程分析法

相对于有限元法,边界单元法在求解断裂问题上有着独特的优势,现有的边界单元法中主要有子区域法和双边界积分方程法.采用一种改进的双边界积分方程法求解二维、三维断裂问题的应力强度因子,对非裂纹边界采用传统的位移边界积分方程,只需对裂纹面中的一面采用面力边界积分方程,并以裂纹间断位移为未知量直接用于计算应力强度因子.采用一种高阶奇异积分的直接法计算面力边界积分方程中的超强奇异积分;对于裂纹尖端单元,提供了三种不同形式的间断位移插值函数,采用两点公式计算应力强度因子.给出了多个具体的算例,与现存的精确解或参考解对比,可得到高精度的计算结果.      

汶川地震诱发文家沟巨型滑坡 碎屑流基本特征及成因机制初步分析


2008年5月12日,汶川M80地震在四川省绵竹市清平乡文家沟内诱发一巨型滑坡。通过现场调查得知,滑坡前后缘高差455m,厚度20～30m,滑面为基岩层面,初始方量2750×107m3。滑体在运动中转化为碎屑流。滑坡-碎屑流总的水平运动距离为4022m,垂直运动距离为1443m,遗留的堆积物体积达5×107m3。滑坡距映秀—北川断裂仅36km,位于其下盘,地震烈度达XI度。滑坡导致文家沟中48人遇害,并形成一条完整的地震次生地质灾害链。初步分析表明滑坡启动速度快,滑坡向碎屑流转化过程明显、地点明确。碎屑流运动过程复杂,伴有强烈的“气垫效应”和“前缘气浪冲击效应”。作者认为,文家沟滑坡的高启动速度是长持时强烈地震动作用的结果,与山体的猛烈碰撞是导致滑体解体并转化为碎屑流的原因。     

Preface: Orbits around asteroid

One of the core issues in modern celestial mechanics is the orbital dynamics in the near-regime gravitational field of as- teroids, which provides deep insights into the mathematical nature of a class of nonlinear systems, and plays as a critical basis for in situ explorations of different science goals. Lots of efforts have been made to reveal the characteristics of orbital motion in the vicinity of asteroids, and to improve the skills of asteroid research in methodology.     

Effet de l'anisotropie élastique cristalline sur la distribution des facteurs de Schmid à la surface des polycristauxInfluence of crystalline elasticity anisotropy on Schmid factor distribution at the free surface of polycrystals

Experimental studies of the plasticity mechanisms of polycrystals are usually based on the Schmid factor distribution supposing crystalline elasticity isotropy. A numerical evaluation of the effect of crystalline elasticity anisotropy on the apparent Schmid factor distribution at the free surface of polycrystals is presented. Cubic elasticity is considered. Order II stresses (averaged on all grains with the same crystallographic orientation) as well as variations between averages computed on grains with the same crystallographic orientation but with different neighbour grains are computed. The Finite Element Method is used. Commonly studied metals presenting an increasing anisotropy degree are considered (aluminium, nickel, austenite, copper). Concerning order II stresses in strongly anisotropic metals, the apparent Schmid factor distribution is drifted towards small Schmid factor values (the maximum Schmid factor is equal to 0.43 instead of 0.5) and the slip activation order between characteristic orientations of the crystallographic standard triangle is modified. The computed square deviations of the stresses averaged on grains with the same crystallographic orientation but with different neighbour grains are a bit higher than the second order ones (inter-orientation scatter). Our numerical evaluations agree quantitatively with several observations and measures of the literature concerning stress and strain distribution in copper and austenite polycrystals submitted to low amplitude loadings. Hopefully, the given apparent Schmid factor distributions could help to better understand the observations of the plasticity mechanisms taking place at the free surface of polycrystals. To cite this article: M. Sauzay, C. R. Mecanique 334 (2006).     

Nonlinear behavior of matrix-inclusion composites under high confining pressure: application to concrete and mortar

This paper is devoted to a micromechanics-based simulation of the response of concrete to hydrostatic and oedometric compressions. Concrete is described as a composite made up of a cement matrix in which rigid inclusions are embedded. The focus is put on the role of the interface between matrix and inclusion which represent the interfacial transition zone (ITZ). A plastic behavior is considered for both the matrix and the interfaces. The effective response of the composite is derived from the modified secant method adapted to the situation of imperfect interfaces. To cite this article: T.H. Le et al., C. R. Mecanique 336 (2008).     

Dynamics and Breakup of Viscoelastic Liquids (A Review)

The phenomena of hydrodynamic breakup of liquid jets, drops, films, bridges, and filaments are reviewed for liquids with viscoelastic properties. The reasons for breakup are capillary instabilities, collisions with rigid obstacles, and other forms of dynamic action. The relationship between the properties of the liquids and the features of the breakup process is discussed.     

Flow stability analysis and excitation using pulsating jets

Classical flow stability applied to transition from laminar to turbulent flow may also describe the behavior of vorticity fluctuations created by a pulsating jet placed along a solid boundary. A numerical laminar flow experiment involving a pulsating jet placed along the surface of a duct with flow separation downstream, resulted in eliminating most part of the separated flow region. Applying the same approach to a turbulent flow, it was possible to develop a turbulent stability flow formulation and apply successfully turbulent pulsating jet flow separation control. To cite this article: D. Skamnakis, K. Papailiou, C. R. Mecanique 333 (2005).