包埋Pt纳米粒子对金属-半导体-金属结构ZnO紫外光电探测器性能的影响

利用射频磁控溅射设备制备ZnO薄膜, 最终制备ZnO/Pt纳米粒子/ZnO 结构的金属-半导体-金属型紫外光电探测器. 研究了Pt纳米粒子处在ZnO薄膜层中的不同深度对金属-半导体-金属型紫外光电探测器响应性能的影响. 结果表明, 探测器的响应度随着Pt纳米粒子在ZnO薄膜层中所处深度的增大而升高. 在60 V偏压下, 包埋Pt最深的探测器在波长365 nm处取得响应度最大值1.4 A·W^-1, 包埋有Pt探测器的响应度最大值为无Pt 纳米粒子探测器响应度最大值的7倍. 结合对ZnO薄膜表面的表征及探测器各项性能的测试, 得出包埋Pt纳米粒子增强器件的响应性能可归因于表面等离子体增强散射.     

表面等离子体增强氧化锌纳米带发光特性的研究

利用简单的化学气相沉积方法在低温下高产量地合成了ZnO纳米带, 并利用磁控溅射对样品进行表面修饰, 制备了Au-ZnO复合纳米带. 通过扫描电镜、透射电镜及微区拉曼等手段系统地研究了表面修饰对ZnO 纳米材料发光性能的影响.结果表明, 在ZnO纳米带上溅射Au纳米颗粒, 可有效增强其近带边发光并使可见发光强度发生淬灭, 从而增强ZnO纳米带的发光性能. ZnO纳米带发光增强因子η最大可达到85倍. 基于Au纳米颗粒的散射、吸收、Purcell增强因子, 以及Ostwald熟化理论, 又进一步探讨了Au-ZnO复合材料的发光机制. 采用表面等离子体耦合的方法可以有效地提高光电半导体器件的发光效率. 关键词： 表面等离体子 光致发光 氧化锌     

电化学方法制备ZnO纳米颗粒掺杂类金刚石薄膜及其场发射性能研究

采用液相电化学沉积技术制备了ZnO纳米颗粒掺杂的类金刚石(DLC)薄膜, 研究了ZnO纳米颗粒掺杂对DLC薄膜场发射性能的影响. 利用X射线光电子能谱、透射电子显微镜、Raman光谱以及原子力显微镜分别对薄膜的化学组成、 微观结构和表面形貌进行了表征. 结果表明: 薄膜中的ZnO纳米颗粒具有纤锌矿结构, 其含量随着电解液中Zn源的增加而增加. ZnO纳米颗粒掺杂增强了DLC薄膜的石墨化和表面粗糙度. 场发射测试表明, ZnO纳米颗粒掺杂能提高DLC薄膜的场发射性能, 其中Zn与Zn+C的原子比为10.3%的样品在外加电场强度为20.7 V/μm时电流密度达到了1 mA/cm². 薄膜场发射性能的提高归因于ZnO掺杂引起的表面粗糙度和DLC薄膜石墨化程度的增加.     

水浴法制备ZnO纳米棒及其场发射性能

用硝酸锌(Zn(NO3)2·6H2O)与六亚甲基四胺(C6H12N4)以等浓度配制成反应溶液,通过水浴法制备出了形貌可控的棒状ZnO纳米结构,讨论了不同反应浓度及衬底对ZnO表面形貌的影响.样品的XRD和扫描电子显微镜分析结果表明,所得产物均为六方纤锌矿结构,在有晶种层的衬底上制备出的ZnO纳米棒沿(001)方向并垂直于衬底表面生长.随着反应浓度的增加,ZnO纳米棒的直径增大,长径比减小.样品的场发射性能测试表明,反应溶液浓度为0.005 mol/L,以铜膜为晶种层的硅衬底上制备出的场发射阴极具有较好的场发射性能.     

两步法制备超疏水性ZnO纳米棒薄膜

采用两步法制备了超疏水性ZnO纳米棒薄膜,在用磁控溅射在普通玻璃衬底上生长一层ZnO籽晶层基础上,利用液相法制备了空间取向高度一致的ZnO纳米棒阵列,经修饰后由亲水性转变为超疏水性.用扫描电子显微镜观察了纳米棒的表面结构,用接触角测量仪测出水滴在ZnO纳米棒薄膜表面的接触角为151°±05°,滚动角为7°.用Cassie模型对ZnO纳米棒薄膜的超疏水性进行了验证. 关键词： ZnO纳米棒 超疏水 两步法     

紫外光表面处理对ZnO纳米粒子的晶体结构与光学性质的影响

利用溶胶凝胶法制备了ZnO纳米粒子,用紫外光照射对其进行表面处理.探讨了表面处理对ZnO纳米粒子晶体结构与光学性质的影响.结果显示:在晶体结构方面,紫外光照射会降低ZnO纳米粒子的团聚现象,缩短晶格常数,使其所受应力由压缩应力释放变为伸张应力,增大表面能,使能量最佳化并稳定而导致ZnO纳米粒子形成再构.在光学性质方面,紫外光照射会使ZnO纳米粒子表面产生较多的氧空位,而氧空位又会使其表面容易吸附羟基,使得ZnO纳米粒子变得更加亲水.     

氧化锌纳米棒场发射性能研究

采用简单物理气相沉积法制备出取向和非取向的氧化锌纳米棒，他们的场致电子发射性能测量结果表明，ZnO纳米棒具有较好的场发射性能，但是高度取向的ZnO纳米棒阵列并不利于获得高的场致电子发射电流密度.这可能是由于高密度ZnO纳米棒之间具有较高的屏蔽效应，降低了ZnO纳米棒阵列的场放大因子，从而影响了其场发射性能.相反，非取向ZnO纳米棒由于相互之间的屏蔽效应比较弱，而且表面存在容易成为发射中心的微小突起，表现出较好的场发射效果.这些结果不仅有助于加深我们对准一维纳米材料场致电子发射性能的理解，也为未来场发射电子器件的实际应用提供了可靠的依据. 关键词： 氧化锌 场发射 非取向     

水热反应中籽晶层对ZnO纳米棒的影响

以Zn(NO3)2·6H2O/HMT为反应物,通过低温水热反应过程,在籽晶衬底上制备了ZnO纳米棒,分别用场发射扫描电子显微镜和X射线衍射仪对ZnO纳米棒形貌与晶体结构进行了表征,并研究了不同方法制备的ZnO籽晶层以及籽晶层厚度对ZnO纳米棒形貌及结晶质量的影响.结果表明磁控溅射籽晶衬底上生长的ZnO纳米棒结晶质量最好,而籽晶层的厚度对ZnO纳米棒的垂直取向性有一定的影响.     

ZnO纳米棒/CdS量子点的制备及紫外-可见探测性能研究

本文采用水热法在ITO衬底上制备了ZnO纳米棒阵列,然后用化学水浴沉积法在纳米棒上制备CdS量子点。分别利用SEM和XRD对样品形貌和晶体结构进行表征。结果表明,球状的CdS量子点均匀地包覆在ZnO纳米棒表面,且结晶质量较好。基于ZnO纳米棒和ZnO纳米棒/CdS量子点制备的探测器对紫外光都具有很好的响应,然而与ZnO纳米棒探测器相比,ZnO纳米棒/CdS量子点探测器在相同条件下的光电流提高了7倍,为0. 52 mA。此外,ZnO纳米棒/CdS量子点探测器对绿光和蓝光也表现出了很好的响应。     

准一维深色纳米ZnO的水热方法生长及其结构和光学性能的调变

本文以高纯度金属锌箔为Zn和衬底,利用传统的水热合成方法制备了深色的纳米结构ZnO. 研究发现,改变制备温度可以调变ZnO样品的颜色和光学性能,尤其是提高温度可以显著地降低可见光波段太阳能的活性. 推测这种现象与ZnO纳米棒顶端的尖锥形貌密切相关,这种结构加剧了光在ZnO纳米棒之间的折射和反应. 改善ZnO的光吸收能力对于提升ZnO基太阳电池的效率有重要意义.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.