高温超导混频器噪声系数测量

基于小型脉冲管制冷机,建立了以Josephson结为混频器的高温超导混频系统,并以Y-因子测量方法为基础,建立了与之配套的噪声系数测量系统。测量出以Josephson结为混频器的超导混频系统的噪声系数。在最好的情况下,测量的噪声系数值为5.50dB。     

高场核磁共振波谱仪宽带前置放大器的研制

宽带前置放大器是磁共振仪器的重要部件,其性能决定了整个仪器X核通道的检测灵敏度. 根据射频电路理论以及磁共振波谱仪整体性能指标的要求,设计并实现了可应用于高场核磁共振波谱仪的高性能宽带前置放大器. 实测结果表明,所研制的核磁共振波谱仪宽带前置放大器在15 MHz~300 MHz频率范围内,其工作性能达到：带内增益>38 dB,带内平坦度<1.5 dB,噪声系数基本保持在1.2 dB以下,射频开关切换时间<1.5 μs,具有带内增益平坦度高,噪声系数小,发射状态下放大器前端保护电路隔离度高,以及工作状态检测电路准确、简洁的特点. 同时高场核磁共振碳和磷等杂核实验显示,利用所研制的宽带前置放大器可检测到具有较高信噪比的NMR信号.     

Low noise double pass L-band erbium-doped fiber amplifier

A new double pass long wavelength band erbium-doped fiber amplifier with enhanced noise figure characteristics is demonstrated. The noise figure is improved by about 2.6 dB with the incorporation of broadband conventional-band fiber Bragg grating (FBG) in between the two segments of erbium-doped fiber. By incorporating both the pre-amplifier and the FBG, the noise figure is further improved, which varies from 4.0 to 5.0 dB in the flat gain region from 1570 to 1600 nm. The gain varies from 32.0 to 33.4 dB within this region. The new amplifier with high gain and low noise figure can be useful as an inline amplifier in a wavelength division multiplexing transmission system.     

A study of the spectral characteristics of traffic noise attenuation by vegetation belts in Delhi

Traffic noise attenuation at different 1/3-octave frequencies is measured at three vegetation sites and a control site in Delhi, the capital city of India. The study indicates that attenuation generally increases with frequency. At low frequencies, maxima (between 10 and 16 dB) in relative attenuation are observed in the frequency interval between 315 and 400 Hz. Comparatively greater relative attenuation (>20 dB) is observed in the high frequency range between 10 and 12.5 kHz. A significantly higher relative attenuation of more than 24 dB is observed characteristically at 3.15 kHz at all the vegetation sites. The results indicate that vegetation belts could be used as effective barriers for traffic noise control along the roadsides.     

Robustness of NRZ, RZ, CSRZ and CRZ modulation on fiber nonlinearities and amplifier noise at 40 Gbps for (OC-786) long haul link

In this paper, the robustness of NRZ, RZ, carrier-suppressed RZ (CSRZ) and chirped RZ (CRZ) modulation formats at 40 Gbps for (OC-786) long haul link on the amplifier noise figure and fiber nonlinearities has been investigated. The investigations reveals that highest Q²(dB) of the order of [20, 25]; [19, 20]; [18, 19] and [16, 18] has been obtained in case of RZ, CSRZ, CRZ and NRZ modulation formats, respectively, in the presence of fiber nonlinearities and with and without amplifier noise figure of 6 dB. It has been observed that Q²(dB) in case of CRZ fluctuate between 18 and 14 at power variation of −10 to 4 dBm and NF of 6 dB, while it is between 19-9, 20-0 and 16-0 in case of CSRZ, RZ and NRZ. It has been identified that CRZ and CSRZ have shown the robustness on fiber nonlinearity and noise at 40 Gbps up to the transmission distance of 450 km. The wide eye opening in case of CRZ modulation also proved the robustness on fiber nonlinearity and noise.     

Temporary threshold shift in human subject exposed to noise

Using an audiometer,the effect of the noise level upon temporarythreshold shift(TTS)for five trained normal subjects(left ear only)was studied.The measurements were carried out after 6 min exposure(in third octave band)for different sound pressure levels ranging between 75-105 dB at three test fre-quencies 2,3,and 4 kHz.The results indicated that at exposure to noise of soundpressure level(SPL)above 85 dB,TTS increases linearly with ths SPL for all thetest frequencies.The work had extended to study the recovery curves for the sameears.The results indicated that the reduction in TTS on doubling the recoverytimes,for the two sound pressure levels 95 dB and 105 dB,occurs at a rate of near-ly 3 dB.The comparison of the recovery curve at 3 kHz with that calculated usingWard's general equation for recovery was made.Finally,to study the values ofTTS produced by exposure to certain noise at different test frequencies,distribu-tion curves for two recovery times were plotted representing TTS values,for anexposure     

X波段放大混频组件的研制

介绍了X波段放大混频组件的研制情况。该组件由限幅器、低噪声放大器、镜像抑制混频器及中频放大器四部分组成。该组件具有噪声系数低、镜频抑制度高、输出功率1dB压缩点大、抗烧毁功率大等特点。     

S波段低温低噪声放大器的研制

介绍了基于ADS仿真的低噪声放大器的设计与制作方法;重点研究了LNA的直流偏置、稳定性分析、匹配设计、版图制作和调试;提出了源级负反馈和栅极加并联阻抗的方法来实现了电路全频段稳定和低温正常工作。采用ATF-34143制作了中心频率在2.25的低噪声放大器,在77K温度下,该放大器带内输入输出驻波比小于1.2,增益达到23dB,噪声系数为0.24dB。     

低噪声、高增益的L -band EDFA的实验研究

针对传统的L-band EDFA的工作效率低,提出了一种基于单根光纤光栅、泵浦分配、两段级联的EDFA的新结构,其中的光纤光栅用来反射无用的后向C-band ASE.系统地研究了泵浦比例和光纤光栅波长对增益噪声指数的影响关系.最后经实验验证,得到了低噪声、高增益的L-band的EDFA.其在输入信号光（1570 nm）功率为-30 dBm及泵浦功率为70 mW时,增益为22.26 dB,增益噪声指数为4.96 dB.     

Noise properties of a NMR transceiver coil array

The use of multiple radiofrequency (RF) surface coil elements has applications in both fast parallel imaging and conventional imaging techniques. Through implementation of a simple magnetic decoupling network, 50 Omega matching can be achieved in both the transmitter and receiver chains, enabling the use of conventional RF power amplifiers and preamplifiers for transceive applications. Unlike phased array coil arrangements using low impedance preamplifiers for decoupling, the noise correlation between 50 Omega coils decoupled with discrete components has not been characterized. We have measured the dependence of coil quality factor (Q-factor) and noise correlation on coil separation and shown these quantities to be consistent with theoretical arguments, at least at 4 T (170 MHz). Our results suggest that a coil system for transmission and reception of NMR signals with 50 Omega coils can be built to take advantage of all the benefits of conventional array coils and with the added advantages of using conventional amplifiers.     

Wind dependence of ambient noise in shallow water of Bay of Bengal

This work reports on investigations into the wind dependence of ambient noise in the Bay of Bengal. Ambient noise measurements were made in the shallow water of Bay of Bengal using a portable broadband, high frequency data acquisition system together with a sensitive hydrophone suspended from the measuring platform at a depth of 5 m from the surface where the ocean depth was 25 m. Periodic measurements were carried out for one year corresponding to a wind speed range between 2 m/s and 9 m/s during summer, monsoon and winter seasons. The proportionality of the noise level with wind speed for frequencies ranging from 500 Hz to 6 kHz for each season was studied. The analysis reveals that the correlation between the wind speed and the ambient noise spectrum level was higher at lower frequencies. The results of empirical fitting based on analysis were used for noise level prediction and the model predictions compare well with the measured noise level. Further it was observed that the wind generated noise level measured during summer was approximately 8 dB less than that in other seasons. On the other hand the proportionality between the noise level and the wind speed was less during winter.     

High-frequency audiometric assessment of a young adult population

The hearing thresholds of 37 young adults (18-26 years) were measured at 13 frequencies (8, 9,10,...,20 kHz) using a newly developed high-frequency audiometer. All subjects were screened at 15 dB HL at the low audiometric frequencies, had tympanometry within normal limits, and had no history of significant hearing problems. The audiometer delivers sound from a driver unit to the ear canal through a lossy tube and earpiece providing a source impedance essentially equal to the characteristic impedance of the tube. A small microphone located within the earpiece is used to measure the response of the ear canal when an impulse is applied at the driver unit. From this response, a gain function is calculated relating the equivalent sound-pressure level of the source to the SPL at the medial end of the ear canal. For the subjects tested, this gain function showed a gradual increase from 2 to 12 dB over the frequency range. The standard deviation of the gain function was about 2.5 dB across subjects in the lower frequency region (8-14 kHz) and about 4 dB at the higher frequencies. Cross modes and poor fit of the earpiece to the ear canal prevented accurate calibration for some subjects at the highest frequencies. The average SPL at threshold was 23 dB at 8 kHz, 30 dB at 12 kHz, and 87 dB at 18 kHz. Despite the homogeneous nature of the sample, the younger subjects in the sample had reliably better thresholds than the older subjects. Repeated measurements of threshold over an interval as long as 1 month showed a standard deviation of 2.5 dB at the lower frequencies (8-14 kHz) and 4.5 dB at the higher frequencies.     

Absorption of sound at a surface exposed to flow and temperature gradients

In noise abatement using porous or fibrous materials, accurate determination of the surface impedance representing the absorber is decisive for simulation quality. The presence of grazing flow and non-homogeneous ambient temperature influence the reaction of the absorber and may suitably be included in a modified “effective” surface impedance. In this paper, this approach is applied to a generic case representative for the engine bay of a heavy truck, where porous shields suppress the radiated noise, e.g. during a pass-by noise test. The change in the absorption is determined numerically by solving the wave propagation through a layer of varying temperature and flow adjacent to the impedance surface for different angles of incidence. The study shows significant impact of both flow and temperature, especially for materials with low absorption. The diffuse field absorption coefficient is also derived and although the effect is less pronounced in this case, it is still important in lower frequencies and in the frequency range typical for IC engine noise. The proposed numerical method is shown to be accurate and efficient for determination of the effective impedance and moreover not limited to thin boundary layers.     

Investigation of the optical gain and noise figure for multi-channel amplification in EDFA under optimized pump condition

We present the results of an investigation of optical gain and noise figure for simultaneous multi-channel amplification of an erbium doped fibre amplifier (EDFA) under optimized pump condition. Different pump configurations with varying input signal levels show interesting features on gain flatness. In the experiment, population inversion along the fibre length which determines the gain-spectra and noise characteristics of the amplifier is adjusted through optimized fibre length and injected pump power in order to minimize the gain-tilt at C-band. It is observed that bi-directional pumping manifests the best combination of low noise and high gain of EDFA which are useful as in-line repeaters in WDM network. We obtain 30 ± 1.5 dB intrinsically flat small signal gain from 1538 nm to 1558 nm band of wavelength with noise figure <4 dB for 16-channel simultaneous amplification in a single stage EDFA without gain flattening filter.     

Simulation Performance of Erbium-Doped Fiber Amplifiers

In this paper, a simple approach is introduced to simulate the main performance of erbium-doped fiber amplifiers by using two empirical formulas to calculate saturated gain and corresponding noise figure. Then conflict equations are presented to improve this approach. At the end of the paper the comparison of calculation results before and after improvement is given. It has been shown to be more accurate.     

Amplification characteristics measurement of 1.55 μm multi-mode LD

The amplification characteristics of 1.55 μm multi-mode LD are presented experimentally. It demonstrates that nine wavelengths across 1547–1557 nm have a good amplification, the maximum gain of ∼43 dB at 1552.14 nm is obtained with pump power of 130 mW @980 nm, and noise figure of ∼5.6 dB at 1554.3 nm is achieved.     

掺Er及Yb-Er共掺Al2O3光波导放大器噪音特性的数值模拟

利用由速率方程、有限元场分布、传输方程构建的综合理论模型,数值求解了掺Er及Yb-Er共掺Al2O3光波导放大器的噪音系数和正反向自发辐射功率.结果表明,随波导长度的增加,当增益开始下降时,噪音系数显著增加.同时显示了抽运功率和掺杂浓度对噪音系数的影响,比较了两种掺杂放大器的噪音系数,Yb-Er共掺比只掺Er的约小0.8 dB.     

前置放大器在高频信号检测系统中的作用

利用约瑟夫森效应获取电磁信号的频谱信息是超导电子学的重要应用之一.我们在实验室已搭建的高频信号频谱检测系统基础上,研究了前置放大器的噪声参数对整个高频信号检测系统性能产生的影响.通过实验,我们将两个不同输入电压噪声密度的低噪声放大器应用于检测系统,并对所得的结果进行了比较.讨论了在前置放大器方面对基于约瑟夫森效应的液氮温区的小型高频信号检测系统进行改进的可能性.     

Simulation and experimental characterization of Raman/EDFA hybrid amplifier with enhanced performance

We present simulation and experimental characterization of a hybrid amplifier comprising of a Raman amplifier and an erbium doped fiber (EDF) amplifier, with enhanced performance. The incorporation of a pumped EDF section in a fiber Raman amplifier (FRA) employing a dispersion compensating fiber is demonstrated to provide superior performance than a sole FRA system. The hybrid amplifier is characterized in terms of single channel gain and noise figure, and the results of measurements are shown to be in close agreement with the simulated results. Polarization-dependent gain (PDG) and multi-channel measured and simulated gain characterization of the Raman/EDFA hybrid amplifier are also presented.     

Optimization of an Externally Modulated RF Photonic Link

The noise figure and sub-octave spurious-free dynamic range of a carrier-suppressed analog RF photonic link are examined. Expressions for noise figure and dynamic range are derived as a function of the modulator bias angle. A closed form expression for the bias angle that optimizes link noise figure and spurious-free dynamic range is also derived. Experimental results are presented and shown to agree with calculations. These experimental results include some of the lowest noise figure and highest dynamic range results published to date for an RF photonic link incorporating a standard Mach-Zehnder modulator: 6 dB and 122 dB·Hz^2/3, respectively.