Enhancement of Gain in L-Band Bismuth-Based Erbium-Doped Fibre Amplifier Using an Un-pumped EDF and Midway Isolator

A hybrid L-band erbium-doped fibre amplifier (EDFA) with enhanced gain characteristic is demonstrated without a significant noise figure penalty. It uses a backward C-band amplified stimulated emission from both the ends of a bismuth-based EDFA system to pump an unpumped erbium-doped fibre (EDF) for gain enhancing. The maximum gain enhancement of 4.0dB is obtained at wavelength 1604nm with EDF length of 20m. The gain spectrum is reasonably fiat in this amplifier compared with the amplifier without an EDF. The gain varies from 27.4 dB to 30.2 dB at wavelength region 1564-1608 nm with incorporation of 20 m EDF. Noise figure also varies from 6.0 to 7.TdB at this wavelength region.     

High gain double-pass L-band EDFA with dispersion compensation as feedback loop

We demonstrate an efficient double-pass L-band erbium-doped fiber amplifier (EDFA) incorporating chirped fiber Bragg grating (CFBG). The amplifier structure exploits the characteristics of CFBG to reflect the amplified signal back into the gain medium, filter out the recycled forward amplified spontaneous emission and block the residual 1480 nm pump power. The amplifier configuration has high gain and low noise figures as compared to double-pass EDFA using broadband mirror. The demonstrated amplifier has gain of more than 48 dB and low noise figure of less than 4 dB at low input signal power of −40 dBm.     

High-gain and low-noise-figure erbium-doped fiber amplifier employing dual stage quadruple pass technique

A high-gain and low-noise-figure (NF) erbium-doped fiber amplifier (EDFA) was demonstrated utilizing a new technique called the dual-stage quadruple pass (DSQP) with filters. An efficient amplification occurs at the signal wavelength of 1550 nm when it travels along the DSQP amplifier. The highest gain of 62.56 dB with a low noise figure of 3.98 dB was achieved for an input signal power of −50 dBm and pump powers of 10 and 165mW in the second and first stage amplifiers respectively.     

Limitation in the intrinsic method of EDFA gain optimization for 32 × 40 Gbit/s WDM systems

The gain flattening of the erbium doped fiber amplifier (EDFA) is one of the most important aspects in the EDFA which the gain is wavelength dependent. For the first time the limitation of EDFA gain optimizing for a 32-channel wavelength division multiplexing (WDM) systems is investigated and reported in this paper. In a 32-channel WDM system the most favorable flatness gain achieved was 23.16 ± 1.51 dB with an average noise figure of 5.70 dB. This outcome proposes that the method does not achieve a uniform spectral gain in a 32-channel WDM system that incorporates a bandwidth of around 25 nm. Based on the simulation results the intrinsic optimization of EDFA causes the poor SNR and peak signal power with great variation over a transmission distance of 480 km single mode fiber.     

Experimental and theoretical studies on a double-pass C-band bismuth-based erbium-doped fiber amplifier

Performance of a Bismuth-based Erbium-doped fiber amplifier is experimentally and theoretically investigated using 1480 nm pumping with double-pass scheme. In the theoretical analysis, the rate and power propagation equations are solved to examine the optimum length for the C-band operation as well as the gain and noise figure characteristics. The calculated small signal gain is 38 dB with gain variation of less than 3 dB. The measured gain is 4 dB lower due to spurious reflections which were ignored in the theoretical analysis. At input signal power of 0 dBm, a gain of 14.5 dB is obtained experimentally with gain variation of less than 1 dB within the wavelength region from 1530 to 1565 nm. The noise figure is less than 12 dB within this region.     

Gain and noise figure improvements in double-pass S-band EDFA

Double-pass short-wavelength band erbium-doped fiber amplifier (S-band EDFA) with enhanced gain and noise figure characteristics is demonstrated. It uses a broadband fiber Bragg grating (FBG) operating in conventional-band (C-band) region to reduce the C-band amplified spontaneous emission (ASE) in the amplifier system and thus increases the population inversion in the S-band region. The small signal gain is increased by about 2.7 dB for 1500 nm signal at pump power of 103 mW, compared with that of the conventional double-pass amplifier without the FBG. The corresponding noise figure is also improved by 0.5 dB.     

Design of dual-core resonant leaky optical fibre based gain flattening filters for erbium doped fibre amplifiers

We propose optical fibre based filters employing dual-core resonant leaky structure for gain equalization of erbium doped fibre amplifier (EDFA). Spectral loss variation of the structure has been utilized to suppress gain peak and, thus, flatten overall gain profile in the C-band. We show 15.7 dB flat gain with ± 1.6 dB ripple in the wavelength range from 1525 nm to 1555 nm using a single filter and 18±0.7 dB gain using two cascaded filters.     

The L-band EDFA of high clamped gain and low noise figure implemented using fiber Bragg grating and double-pass method

The L-band erbium-doped fiber amplifier (EDFA) of low noise figure and high clamped-gain using gain-clamped and double-pass configuration is presented in this paper. A total of five different configurations of EDFAs by reflection scheme with single forward pumping schemes are examined and compared here. Among these configurations, we first find the configuration of 1480-nm pumped L-band EDFA with optimum gain and noise figure value. To further minimize the gain variation, a fiber Bragg grating (FBG) with 1615-nm center wavelength and 1-nm bandwidth is determined and added in double-pass L-band EDFA. The gain variation and maximum noise figure of EDFA while channel dropping is investigated. As the number of channel dropping from 32 to 4, the L-band type-A EDFA keep the variation of gain within 2.9 dB and the maximum noise figure below 5 dB with each channel’s input power of −23 dBm.     

Gain and Noise figure performance of erbium doped fiber amplifiers (EDFAs) and Compact EDFAs

In this paper, we compare the Gain and Noise figure characteristics of physical EDFAs and Compact EDFAs in an optical system consisting of cascade of both the amplifiers. We demonstrate the gain, noise figure variations of a forward pumped EDFA and Compact EDFAs as functions of Er³⁺ fiber length, injected pump power and up-conversion co-efficient. It is observed that the gain becomes constant when the length of both the amplifiers reaches above 20 m. The comparison shows that the higher gain with flatter output is obtained in case of Compact EDFAs than Physical EDFAs in a system consisting of chain of both the amplifiers. It is further investigated that the agreement between the Compact and Physical EDFA models is good up to 10 m with the no up-conversion co-efficient. Also, the noise figure obtained in case of Physical EDFA is higher than Compact EDFAs when same amplifier length is more than 20 m and then becomes constant for both the amplifiers.     

The temperature dependency of EDFAs in the 1480 nm pumping configuration

A theoretical study of the temperature-dependent gain and noise figure effects on erbium-doped fiber amplifiers (EDFAs) pumped at 1480 nm is investigated, solving the propagation equations related to two level systems. The solution of these equations is based on the population and temperature difference among amplification levels. The temperature-dependent propagation equation considered is used to determine the gain and noise figure effects on EDFAs. The population difference depends on pump and signal powers, Boltzmann factor K_B, cross-sections, noise figure (NF) and Er³⁺ concentration. The temperature-dependent gain and noise figure effect the EDFA length are numerically obtained for the temperature range of −20 °C to +60 °C. All of the analyses consist of the amplified spontaneous emission (ASE) effect.     

An experimental investigation of the gain spectrum of erbium-doped fiber amplifiers under various system configurations

The paper presents an experimental investigation of the gain spectrum of an erbium-doped fiber amplifier (EDFA) considering different system configurations, which include single-pass, double-pass, and double-pass with tunable band-pass filter (TBF). The role of TBF is to suppress the undesired amplified spontaneous emission (ASE). Both co- and counter-pumping schemes are considered with a 1480 nm laser diode as the pump and a suitable tunable laser source as the signal source. The results indicate that the signal achieves an average of 14 dB higher gain in the case of double-pass amplification with the implementation of a TBF. However, the pumping scheme hardly becomes of much importance in influencing the gain characteristics.     

Gain clamped L-band EDFA with forward–backward pumping scheme using fiber Bragg grating

The paper proposes a novel two stage L-band erbium doped fiber amplifier with forward–backward pumping scheme for transmission of 32 wavelength division multiplexed (WDM) channels. It is gain clamped with an in-line fiber Bragg grating (FBG) to provide flat gain over 45 nm by restricting and reutilizing amplified spontaneous emission (ASE). We demonstrate that it provides an efficient small signal gain with minimum noise figure of over 20 dB and 5.5 dB, respectively, in the L-band region (1565–1610 nm) by comparing with its forward and backward pumped counterparts with fixed Er³⁺ fiber length of 20 m for −30 dBm/channel input power. We also obtain the gain and noise figure dependence as a function of each of the Er³⁺ fiber lengths, pump power (both 1480 and 980 nm), and temperature. Hence a 10 nm region (1580–1590 nm) has been acknowledged where temperature variations become constricted for 30 °C variations (15–45 °C).     

A theoretical study of double-pass thulium-doped fiber amplifiers

An efficient fluoride-based thulium-doped fiber amplifier (TDFA) is theoretically demonstrated using a double-pass scheme. A reflector is incorporated in the double-pass TDFA to allow double propagation of the test signal in the gain medium and thus improve the gain of the TDFA. The small signal gain improvement of more than 15 dB is obtained in the 1465 nm region. A gain as high as 42 dB is obtained in this region with 300 mW of 1050 nm pump using 20 m of thulium-doped fiber. However, a noise figure penalty of approximately 1 dB is also obtained in this wavelength region. Differential equations are solved using the Runge-Kutta method in the theoretical analysis. The theoretical result is in agreement with the experimental result.     

低噪声、高增益的L -band EDFA的实验研究

针对传统的L-band EDFA的工作效率低,提出了一种基于单根光纤光栅、泵浦分配、两段级联的EDFA的新结构,其中的光纤光栅用来反射无用的后向C-band ASE.系统地研究了泵浦比例和光纤光栅波长对增益噪声指数的影响关系.最后经实验验证,得到了低噪声、高增益的L-band的EDFA.其在输入信号光（1570 nm）功率为-30 dBm及泵浦功率为70 mW时,增益为22.26 dB,增益噪声指数为4.96 dB.     

Noise figure and gain temperature dependent of praseodymium-doped fiber amplifier by using rate equations

A theoretical study of the temperature dependent noise effects of praseodymium-doped fiber amplifiers (PEDFAs) has been examined. The Pr³⁺-doped ZBLAN fiber amplifier pumped at 1017 nm and Pr³⁺-doped GeGa-sulfied fiber amplifier pumped at 1028 nm are chosen. The temperature-dependent rate and propagation equation related to four-level system consideration which is based on the population difference among amplification levels has been used. The population difference depends on pump and signal powers, Boltzman factor K_B, cross-sections, noise figure (NF) and Pr³⁺ concentration. The numerical results obtained over the temperature range from −20 °C to + 60 °C are used to present an analytical expression for the signal gain and noise figure effects in PDFAs length and noise figure with input pump power. The amplified spontaneous emission (ASE) has been taken into account.     

Double-pass erbium-doped zirconia fiber amplifier for wide-band and flat-gain operations

The double-pass erbium-doped zirconia fiber amplifier (EDZFA) is proposed and demonstrated to provide a wide-band amplification as well as flat-gain operation in both the C- and L-band regions using only a single-gain medium. The proposed amplifier utilizes an erbium-doped zirconia fiber (EDZF) with erbium ion concentration of 2800 ppm as a gain medium. The medium is fabricated in a ternary glass host, zirconia-yttria-aluminum codoped silica fiber through solution doping technique along with modified chemical vapor deposition (MCVD). Compared to a single-pass operation, the double-pass EDZFA shows a better gain performance. At input signal power of 0 dBm and the optimum EDZF length of 2 m, a flat gain of around 16 dB is achieved by the proposed double-pass amplifier with gain variation of approximately 2.5 dB throughout the wavelength range from 1530 to 1590 nm. However, the noise figure of the double-pass amplifier is slightly higher than that of the single-pass due to inefficient population inversion at the input part of the amplifier.     

A dual pumped double-pass L-band EDFA with high gain and low noise

This paper presents an efficient pumping scheme for L-band erbium-doped fiber (EDFA) amplifier to reach high gain and low noise performance in a double-pass configuration. The main L-band amplifier is composed of two sections of EDFs. A 980 nm and a 1480 nm pump lasers are used to pump the first section of EDF bi-directionally. The generated backward C-band amplified spontaneous emission noise from this EDF is used to pump a subsequent un-pumped section of EDF. In the double-pass scheme, a narrow-band fiber Bragg grating at each channel wavelength is used to back-reflect the L-band signal to make it amplified twice by the pair of EDFs. Compared with its conventional counterpart, this new double-pass configuration provides a lower noise figure and a higher gain. The pump conversion efficiency can be improved by more than 50% in a 3-channel demonstration by using the proposed configuration.     

An effective numerical method for gain profile optimizations of multi pumped fiber Raman amplifiers

In this paper, we have solved propagation equations of multi-pump fiber Raman amplifier using Runge–Kutta (RK 4th order) numerical method and pump power evolutions along with the fiber length. They are used to calculate the net gain and gain ripple by varying the input signals powers for different fiber lengths. The pump powers are optimized by genetic algorithm and resulting net gain and gain ripple are reported graphically as well as in tabular form. The optimum minimum gain ripple is 0.26 dB for 1 mW input signal powers for 50 km fiber length. By increasing the fiber length gain ripple increases to 0.5 dB for 0.1 mW input signal power. In comparison to other methods reported in the literature, our method is simple to implement and efficient for numerical design of Raman amplification in optical communication systems.     

New trend for optical signal-to-noise ratio of disturbed Raman fiber amplifier

In a distributed Raman fiber amplifier (DRFA), Raman amplification allows a lower signal launch powers to transverse the span above the noise floor while still increasing the optical signal-to-noise ratio (OSNR). It improves the noise figure and reduces the nonlinear penalty of fiber systems. In this paper, we demonstrate a new trend of OSNR at different pump configurations: forward, backward and bidirectional pumping for DRFAs as a function of fiber length. We also present the variation of OSNR with both input pump power and input signal power. It is found that forward pumping provides the highest OSNR, reaching its maximum value of 37 dB. However, backward pumping provides the smallest OSNR that has its maximum of 22 dB and the bidirectional pumping provides the moderate OSNR between the others having its peak of 26 dB.     

Characteristics of low noise hybrid fiber amplifier

The characteristics of hybrid fiber amplifier (HFA) are investigated. HFA is composed of three stages: short-length EDFA pre-stage, DCF Raman amplifier, and power boosting EDFA. HFA has low noise figure, high output power, and also wide input power dynamic range. Gain control method of HFA is presented experimentally, and the transient gain excursion is suppressed to less than 0.5 dB at 3 dB channel add-drop. HFA can be used as line amplifier in optical transmission link even combined with distributed Raman amplifier due to wide input power dynamic range. The transmission performance of HFA is better than EDFA by more than 1.0 dB of Q-factor in 720 km SMF transmission.