由Giles模型对L-band EDFA的理论分析

本文通过运用Giles模型对L-band EDFA在不同泵浦波长下的增益、不同泵浦功率与光纤长度的关系以及各种增益特性等进行了数值模拟,并同时辅以C-band EDFA进行比较计算,从理论上对L-band EDFA的特性进行了较为详细的分析说明,并得出了新颖的结论.     

基于长周期光纤光栅滤波器的掺铒光纤放大器理论和实验研究

从理论和实验上研究了带有高频二氧化碳激光写入的低成本长周期光纤光栅（LPFG）掺铒光纤放大器（EDFA）.结果表明,单波长和多波长EDFA的性能都可以通过在掺铒光纤（EDF）中插入长周期光纤光栅用作自发辐射噪声（ASE）滤波器或增益平坦器来提高性能.优化设计了带LPFG噪声滤波器的线放EDFA,与没有LPFG噪声滤波器相比,线放的噪声和小信号增益分别被减小和提高了约0.5 dB和7 dB。通过在多波长EDFA的EDF中插入一个LPFG增益平坦滤波器的方法,获得了1.5 dB的增益平坦度,与没有LPFG平坦器相比,EDFA的噪声被减小了0.1 dB,增益被提高了1 dB.     

L-Band掺铒光纤放大器的优化设计

提出了泵浦分配两段级联,并利用前向ASE推动下一级EDF工作的L-Band放大器的新结构.基于Giles模型并考虑了ASE噪声的影响,运用数值模拟算法系统分析了泵浦光功率分配和铒光纤分配比例对这种EDFA性能的影响.最后优化得到高增益且增益谱平坦的L-Band EDFA,其在输入信号光功率为-20 dBm时,在1571～1608 nm范围内,增益值高达35 dB,增益偏差小于1 dB.     

掺铒光纤放大器的理论模拟与全局分析

基于Giles模型并考虑了ASE噪音,对各种泵浦方式下的掺铒光纤放大器(EDFA)进行了数值模拟.提出了一种新的分析方法(增益噪音指数全局分析法),直观有效地分析了EDFA的增益和噪音指数与掺铒光纤长度和泵浦功率的依赖关系,并对各种EDFA的性能作了全面的比较.     

WDM用增益平坦的高增益低噪声双段级联掺铒光纤放大器

给出了设计波分复用(WDM)用高增益、低噪声和宽带宽增益平坦的双段级联掺铒光纤放大器(EDFA)的一般步骤和方法.通过优化设计各种参量,研制出了一台高增益、低噪声和宽带宽增益平坦的双段级联EDFA样机,实现了从1524.8～1561.4 nm共36.6 nm带宽内±0.325 dB的平坦增益,0 dBm输入时,饱和输出功率大于15 dBm的高功率输出;噪声指数低于5 dB.     

长波段掺铒光纤放大器用掺铒光纤的设计考虑

本文分析了长波段掺铒光纤放大器(EDFA)的增益系数与Er³⁺离子浓度的关系.研制了铝共掺杂的高浓度掺铒光纤,以缩短长波段掺铒光纤的长度.用两级泵浦实现了L-波段EDFA.光纤放大器的掺铒光纤总长18m,在1570nm波长处的小信号增益为42.26dB,输出功率为17.5dBm.我们认为,较低的浓度淬灭效应归因于光纤中较高的A1掺杂浓度.当总的输入信号功率为-3dBm时,在1570至1600nm间的7路WDM信号的增益不平坦度仅为0.68dB..     

双包层掺镱光纤激光器连续和调Q运转的实验研究

采用布拉格光纤光栅作为谐振腔,实现了980 nm半导体激光器端面泵浦下的双包层掺镱光纤激光器的连续和调Q运转.连续激光实验结果表明,在泵浦功率固定时,增益光纤存在激光输出功率最大情况下的最佳长度,当泵浦功率增大时,最佳增益光纤长度也随之增加.采用石墨烯分散液作为可饱和吸收体,插入增益光纤与布拉格光纤光栅之间,实现了光纤激光器的稳定被动调Q运转.当泵浦功率为2.87W时,得到了最小脉冲宽度33 ns、重复率38.5 kHz的脉冲序列;随着泵浦功率进一步增大,出现不稳定的调Q锁模现象.     

高掺杂碲基EDFA增益噪声特性的数值模拟

采用四能级理论模型对高掺杂碲基EDFA进行了数值模拟,得出C波段和L波段EDFA的主要增益和噪声系数特性,C+L波段同时放大时,20 dB增益带宽达到85 nm.同时分析了铒离子高掺杂带来的上转换效应对放大增益和噪声性能的影响程度,C波段为4％,L波段为10％,当增大泵浦光功率时,影响程度会更小,采用两段级双向泵浦结构放大时影响仅为0.1％.     

用于长距离光学频率传递链路的双向掺铒光纤放大器的优化设计

光纤链路中高精度光学频率传递对光钟比对有重要意义,双向掺铒光纤放大器(EDFA)有助于在长距离光学频率传递中对信号进行损耗补偿和高精度传输。基于铒粒子受激放大的基本原理,设计了可用于光纤光学频率传递链路中的低噪声、高增益双向EDFA,并对其参数进行了仿真优化。实验结果表明,该双向EDFA的噪声指数为3.86dB,增益为20.14dB,引入的相位噪声在频率为1Hz处仅为0.1rad2/Hz。将该双向EDFA作为放大补偿器件应用于200km光纤光学频率传递链路中,获得了3.8×10-16/s的秒级频率稳定度及2.8×10-19/(104 s)的万秒级频率稳定度,在频率信号传递和光钟比对领域有着广阔的应用前景。     

L-band EDFA性能与增益光纤长度关系的分析

分析和模拟L_band EDFA的增益特性对其优化设计和实验有着重要的意义。基于Giles模型,数值模拟了L_band EDFA中的信号光、泵浦光和放大自发辐射(ASE)在一定泵浦功率下与铒光纤长度的关系;分析了L_band EDFA本征增益平坦的产生机理;数值模拟了小信号增益平坦特性。结果表明,在一定的泵浦功率下,如果在所选择的L_bandEDFA中铒光纤长度合适,则不需要任何平坦化处理就可以得到比较平坦的增益谱线。     

High gain double-pass L-band EDFA with dispersion compensation as feedback loop

We demonstrate an efficient double-pass L-band erbium-doped fiber amplifier (EDFA) incorporating chirped fiber Bragg grating (CFBG). The amplifier structure exploits the characteristics of CFBG to reflect the amplified signal back into the gain medium, filter out the recycled forward amplified spontaneous emission and block the residual 1480 nm pump power. The amplifier configuration has high gain and low noise figures as compared to double-pass EDFA using broadband mirror. The demonstrated amplifier has gain of more than 48 dB and low noise figure of less than 4 dB at low input signal power of −40 dBm.     

The L-band EDFA of high clamped gain and low noise figure implemented using fiber Bragg grating and double-pass method

The L-band erbium-doped fiber amplifier (EDFA) of low noise figure and high clamped-gain using gain-clamped and double-pass configuration is presented in this paper. A total of five different configurations of EDFAs by reflection scheme with single forward pumping schemes are examined and compared here. Among these configurations, we first find the configuration of 1480-nm pumped L-band EDFA with optimum gain and noise figure value. To further minimize the gain variation, a fiber Bragg grating (FBG) with 1615-nm center wavelength and 1-nm bandwidth is determined and added in double-pass L-band EDFA. The gain variation and maximum noise figure of EDFA while channel dropping is investigated. As the number of channel dropping from 32 to 4, the L-band type-A EDFA keep the variation of gain within 2.9 dB and the maximum noise figure below 5 dB with each channel’s input power of −23 dBm.     

Effect of injection of C-band ASE on L-band erbium-doped fiber amplifier

The effect of injecting conventional band (C-band) amplified spontaneous emission on the performance of long-wavelength band erbium-doped fiber amplifier (L-band EDFA) is demonstrated. It uses a circulator and broadband fiber Bragg grating (FBG) to route C-band ASE from a C-band EDFA. Injection of a small amount of ASE (attenuation of 20 dB or above) improves the small signal gain with a negligible noise figure penalty compared to that of an amplifier without the ASE injection. A maximum gain improvement of 3.5 dB is obtained at an attenuation of 20 dB. At very large amounts of ASE injection (attenuation of 0 dB), the gain of the amplifier is clamped at 15.2 dB from ?40 to ?10 dBm with a gain variation of less than 0.3 dB. The saturation power is also increased from ?8 dBm (for without ASE injection) to 2 dBm (VOA=0 dB) with a slight noise figure penalty. These results show that the ASE injection technique can be used either for gain improvement or for gain clamping in L-band EDFA.     

Bidirectional-pumped L-band erbium-doped fiber amplifier with pump distribution technique

A dual-stage erbium doped fiber amplifier (EDFA) having a flat gain wavelength response throughout L-band transmission window is presented. By applying pump power distribution technique, the pump power is distributed to two different stages with different length of EDF depending on the coupling ratio. By controlling these two parameters, gain of 19.1 dB with small gain variation of less than 0.5 dB and a noise figure of less than 10.5 dB are achieved in this architecture using bidirectional pumping. However, when another 3 dB power coupler is added to split the pump power equally at the second stage in bidirectional, a better noise figure of less than 7.5 dB was obtained. Comparison with a conventional single-stage optical amplifier was made in order to validate the performances of this dual-stage EDFA.     

Gain-clamping in two-stage L-band EDFA using an unwanted backward ase from second stage

A gain clamping technique for the long wavelength band erbium-doped fiber amplifier (L-band EDFA) is presented. It uses two circulators and a broad band fiber Bragg grating to route wasted backward C-band ASE from the second stage and launch it back into the input end of the first stage of a two-stage amplifier. The two-stage L-band EDFA has shown a small signal gain improvement of 5.7 dB compared to a single-stage amplifier with a slight noise figure degradation. By utilizing the wasted backward ASE, a L-band gain-clamped EDFA with high gain can be realized. Compared to the unclamped case, this gain-clamping technique is effective in reducing the total gain variation as small as 0.3 dB.     

Low noise gain-clamped L-band erbium-doped fiber amplifier by utilizing fiber Bragg grating

A novel gain-clamped long wavelength band (L-band) erbium-doped fiber amplifier (EDFA) is proposedand experimented by using a fiber Bragg grating (FBG) at the input end of the amplifier. This designprovides a good gain clamping and decreases noise effectively. It uses two sections of erbium-doped fiber(EDF) pumped by a 1480-nm laser diode (LD) for higher efficiency and lower noise figure (NF). The gainis clamped at 23 dB with a variation of 0.5 dB from input signal power of -30 to -8 dBm for 1589 nm andNF below 5 dB is obtained. At the longer wavelength in L-band higher gain is also obtained and the gainis clamped at 16 dB for 1614 nm effectively. Because the FBG injects a portion of backward amplifiedspontaneous emission (ASE) back into the system, the gain enhances 5 dB with inputting small signal.     

A dual pumped double-pass L-band EDFA with high gain and low noise

This paper presents an efficient pumping scheme for L-band erbium-doped fiber (EDFA) amplifier to reach high gain and low noise performance in a double-pass configuration. The main L-band amplifier is composed of two sections of EDFs. A 980 nm and a 1480 nm pump lasers are used to pump the first section of EDF bi-directionally. The generated backward C-band amplified spontaneous emission noise from this EDF is used to pump a subsequent un-pumped section of EDF. In the double-pass scheme, a narrow-band fiber Bragg grating at each channel wavelength is used to back-reflect the L-band signal to make it amplified twice by the pair of EDFs. Compared with its conventional counterpart, this new double-pass configuration provides a lower noise figure and a higher gain. The pump conversion efficiency can be improved by more than 50% in a 3-channel demonstration by using the proposed configuration.     

Gain-clamping techniques in two-stage double-pass L-band EDFA

Two designs of long-wavelength band erbium-doped fiber amplifier (L-band EDFA) for gain clamping in double-pass systems are demonstrated and compared. The first design is based on ring laser technique where a backward amplified spontaneous emission (ASE) from the second stage is routed into the feedback loop to create an oscillating laser for gain clamping. The gain is clamped at 18.6 d B from -40 to -80 dBm with a gain variation of less than ±0.1 dB and a noise figure of less than 6 dB. Another scheme is based on partial reflection of ASE into the EDFA, which is demonstrated using a narrowband fiber Bragg grating. This scheme achieves a good gain clamping characteristic up to -12 dBm of input signal power with a gain variation of less than ±0.3 dB from a clamped gain of 22 dB. The noise figure of a 1580 nm signal is maintained below 5 dB in this amplifier since this scheme is not based on lasing mechanism. The latter scheme is also expected to be free from the relaxation oscillation problem.     

Amplification enhancement of L-band erbium-doped fiber amplifiers by reflection scheme

A reflection L-band erbium-doped fiber amplifier (EDFA), which can effectively suppress and completely exploit the backward C-band amplified spontaneous emission (ASE) with a feedback reflection loop, is presented in this paper. The mechanism of the backward ASE secondary pumping effect is experimentally investigated in detail. Our experimental results have shown that, for a given input pump power, compared to the end-pumped EDFA, the gain and output power of the reflection EDFA can be improved considerably without paying much noise penalty. When the EDFA operates with flattened gain spectra, the gain is improved by about 7 dB with an extra noise penalty of about 1.2 dB, where the saturation output power is increased by 2.5–3.2 dB and which may also be made independent of the input signal power.     

Gain and noise figure improvements in double-pass S-band EDFA

Double-pass short-wavelength band erbium-doped fiber amplifier (S-band EDFA) with enhanced gain and noise figure characteristics is demonstrated. It uses a broadband fiber Bragg grating (FBG) operating in conventional-band (C-band) region to reduce the C-band amplified spontaneous emission (ASE) in the amplifier system and thus increases the population inversion in the S-band region. The small signal gain is increased by about 2.7 dB for 1500 nm signal at pump power of 103 mW, compared with that of the conventional double-pass amplifier without the FBG. The corresponding noise figure is also improved by 0.5 dB.