光子晶体发光二极管

利用光子晶体的光子禁带和光栅衍射效应可以提高LED的出光效率,扩大LED的应用范围。总结了光子晶体发光二极管的原理和典型器件。通过比较表明,与光子禁带效应相比,利用光栅衍射效应提高LED出光效率的方法更适用于电注入发光。因此可望用更廉价的方法在LED表面制造光子晶体,可通过光栅衍射效应来有效地提高其出光效率。     

Optical design and optimization of light emitting diode automotive head light with digital micromirror device light emitting diode

This research proposes a new method for light emitting diode automotive headlight design with digital micromirror device (DMD). The optical design is advanced because of the following features. First, this optical design controls the angle of light pattern without light masking so as to achieve much higher light efficiency compared with traditional optical design for headlight systems. Second, in view of the tendency that the advanced light emitting diode automobile headlight is designed to be a low beam light module and a high beam light still needs an auxiliary lighting system, the optical system designed in this research, mainly adopting DMD module as high/low beam light switch, can switch on and off both the high and low beam lights. Because DMDs function of accepting a bidimensional image, high/low beam light patterns can be determined by DMD. Third, a light pattern will be created and compensated simultaneously by DMD, which might replace mechanical adaptive front-lighting system in the future because DMD takes advantage of fast response and simultaneous compensation. Fourth, a design using a multiple reflection curved mirror is employed in this research to adjust light energy distribution; therefore, the articulation of the light pattern can be enhanced. For this method, experimental results of light efficiency are up to 85%, which is superior to current products in the market.     

Quasi-homoepitaxial GaN-based blue light emitting diode on thick GaN templateQuasi-homoepitaxial GaN-based blue light emitting diode on thick GaN templateQuasi-homoepitaxial GaN-based blue light emitting diode on thick GaN templateQuasi-homoepitaxial GaN-based blue light emitting diode on thick GaN template

The high power GaN-based blue light emitting diode （LED） on an 80%tm-thick GaN template is proposed and even realized by several technical methods like metal organic chemical vapor deposition （MOCVD）, hydride vapor-phase epi- taxial （HVPE）, and laser lift-off （LLO）. Its advantages are demonstrated from material quality and chip processing. It is investigated by high resolution X-ray diffraction （XRD）, high resolution transmission electron microscope （HRTEM）, Rutherford back-scattering （RBS）, photoluminescence, current-voltage and light output-current measurements. The width of （0002） reflection in XRD rocking curve, which reaches 173＂ for the thick GaN template LED, is less than that for the conventional one, which reaches 258＂. The HRTEM images show that the multiple quantum wells （MQWs） in 80%tm- thick GaN template LED have a generally higher crystal quality. The light output at 350 mA from the thick GaN template LED is doubled compared to traditional LEDs and the forward bias is also substantially reduced. The high performance of 80-~m-thick GaN template LED depends on the high crystal quality. However, although the intensity of MQWs emission in PL spectra is doubled, both the wavelength and the width of the emission from thick GaN template LED are increased. This is due to the strain relaxation on the surface of 80%tin-thick GaN template, which changes the strain in InGaN QWs and leads to InGaN phase separation.     

Effect of surface treatment of GaN based light emitting diode wafers on the leakage current of light emitting diode devices

To form low-resistance Ohmic contact to p-type GaN, InGaN/GaN multiple quantum well light emitting diode wafers are treated with boiled aqua regia prior to Ni/Au (5~nm/5~nm) film deposition. The surface morphology of wafers and the current--voltage characteristics of fabricated light emitting diode devices are investigated. It is shown that surface treatment with boiled aqua regia could effectively remove oxide from the surface of the p-GaN layer, and reveal defect-pits whose density is almost the same as the screw dislocation density estimated by x-ray rocking curve measurement. It suggests that the metal atoms of the Ni/Au transparent electrode of light emitting diode devices may diffuse into the p-GaN layer along threading dislocation lines and form additional leakage current channels. Therefore, the surface treatment time with boiled aqua regia should not be too long so as to avoid the increase of threading dislocation-induced leakage current and the degradation of electrical properties of light emitting diodes.     

基于氧化锌纳米线的紫外发光二极管

构建了基于n-ZnO纳米线/p-Si异质结的紫外发光二极管.ZnO纳米线准阵列采用水热法生长于重掺p型Si片上.此法简易，反应温度低，易于大规模生产；其产物ZnO纳米线结晶良好，以c轴为优势取向，光激发下的紫外荧光发射很强.二极管的电学接触采用聚合物填充的In阴极或以氧化铟锡(ITO)玻璃紧压形成阴极.它们的I-V特性体现出良好的二极管性质.在正向偏置电压驱动下，构建的发光二极管可稳定发射波长在387nm的较强的近紫外光和较弱的绿光. 关键词： ZnO纳米线 异质结 电致发光 水热法     

Blue light emitting diode exceeding 100% quantum efficiency

InGaN/GaN light‐emitting diodes (LEDs) are known to exhibit a strongly non‐uniform vertical carrier distribution within the multi‐quantum well (MQW) active region. We propose to eliminate “dark” quantum wells by insertion of multiple tunnel junctions into the MQW which allow for the repeated use of electrons and holes for photon generation. In good agreement with available measurements, we demonstrate by self‐consistent numerical simulation that such tunnel junction LED design promises quantum efficiencies as high as 250% as well as a strongly enhanced output power at high input power, compared to conventional LED concepts.

     

High efficient plastic substrate polymer white light emitting diode

White polymer light emitting diode (PLED) has attracted the interest of researchers by the advantage of having low cost, flexible light sources. One of the major advantages of PLED is that it can be able to fabricate in flexible plastic substrate instead of glass substrate. Generally PLED??s requires a substrate of high refractive index to enhance the amount of trapped light in the device, but the refractive index of flexible plastic substrate is low (n?<?1.6). In this paper, we present a white PLED on a flexible plastic substrate with a new enhancement method. In which the semi-transparent gold layer is sandwiched between the layers of tantalum oxide and molybdenum oxide which does not require a high refractive index substrate. Using this design, the extraction efficiency of the device is increased from 1.5 to 2.1 cw compared to that of the device using glass substrate.     

发光二极管灯具鳍片式散热结构

为了提高发光二极管（LED）灯具的性能,依据LED散热指标,计算了散热面积,建立了LED鳍片式散热模型,最终利用ANSYS软件对其进行了仿真。研究结果表明:当鳍片间距与鳍片厚度比为3∶2、底座厚度与鳍片厚度为1∶1时,散热效果最好;随着鳍片数目和鳍片高度的增加,散热效果也有所增强。     

Nano-plasmon enhancement effect on MWIR light emitting diode performance

We observed a significant increase in electro luminescence from GaSb based mid-wave infrared (MWIR) LED device through coupling with localized surface plasmon of a single layer Au nano-particles. We fabricated an interband cascade (IC) LED device with nine cascade active/injection layers with InAs/Ga_1−x In_xSb/InAs quantum well (QW) active region. Thin Au plasmon layer of 20 nm thickness is deposited on top anode electrode by e-beam technique, which resulted in 100% increase in light output for 50 μm square mesa device. We also observed a reduction in the device turn on voltage and increase in the apparent black body emission temperature due to nano-structure surface plasmon layer.     

基于量子点和MEH-PPV的白光发光二极管的研究

利用无机纳米材料与有机聚合物材料相结合的方法制备白光发光二极管器件, 研究了蓝光量子点QDs(B)掺杂聚[2-甲氧基-5-(2-乙基己氧基-1, 4-苯撑乙烯撑](MEH-PPV) 复合体系的发光特性及量子点QDs(B) 掺杂浓度(质量分数)不同对器件发光特性的影响. 制备了ITO/PEDOT:PSS/MEH-PPV:QDs(B)/LiF/Al 结构的电致发光器件, 测试了器件的电致发光光谱和电学、光学特性. 当QDs掺杂浓度为40%, 驱动电压为8 V时器件能得到较为理想的白光发射. 同时, 对比研究了非掺杂体系的发光特性, 制备了结构为ITO/PEDOT:PSS/MEH-PPV/QDs(B)/LiF/Al的器件, 掺杂体系相较于非掺杂体系, 器件的最大亮度增大, 启亮电压降低, 并分析了掺杂体系器件性能改善的原因.     

发光二极管可靠性的噪声表征

通过对发光二极管内部结构的研究，发现N_t(界面态陷阱密度)和扩散电流比率 是影响发光二极管性能的重要因素，并与器件可靠性有密切关系.器件内部存在的多种噪声 中，低频1/f噪声可表征N_t和扩散电流比率.在深入研究发光二极管工作原理及1 /f噪声载流子数涨落理论和迁移率涨落理论的基础上，建立了发光二极管的电性能模型及1/ f噪声模型.在输入电流宽范围变化的条件下测量了器件的电学噪声，实验结果与理论模型符 合良好.通过对其测量结果分析，深入研究了噪声和发光二极管性能与可靠性的关系，证明 了噪声幅值越大，电流指数越接近于2，器件可靠性越差，失效率则显著增大. 关键词： 1/f噪声 发光二极管 陷阱 光功率     

Quasi-homoepitaxial GaN-based blue light emitting diode on thick GaN template

The high power GaN-based blue light emitting diode (LED) on an 80-μ-thick GaN template is proposed and even realized by several technical methods like metal organic chemical vapor deposition (MOCVD), hydride vapor-phase epitaxial (HVPE), and laser lift-off (LLO). Its advantages are demonstrated from material quality and chip processing. It is investigated by high resolution X-ray diffraction (XRD), high resolution transmission electron microscope (HRTEM), Rutherford back-scattering (RBS), photoluminescence, current-voltage and light output-current measurements. The width of (0002) reflection in XRD rocking curve, which reaches 173" for the thick GaN template LED, is less than that for the conventional one, which reaches 258". The HRTEM images show that the multiple quantum wells (MQWs) in 80-μm-thick GaN template LED have a generally higher crystal quality. The light output at 350 mA from the thick GaN template LED is doubled compared to traditional LEDs and the forward bias is also substantially reduced. The high performance of 80-μm-thick GaN template LED depends on the high crystal quality. However, although the intensity of MQWs emission in PL spectra is doubled, both the wavelength and the width of the emission from thick GaN template LED are increased. This is due to the strain relaxation on the surface of 80-μm-thick GaN template, which changes the strain in InGaN QWs and leads to InGaN phase separation.     

Effect of encapsulation technology on organic light emitting diode lifetime

A kind of green organic light-emitting diodes (OLED) was prepared via vacuum thermal evaporation, of which the multilayer structure was indium-tin oxide (ITO)/copper-phthalocyanine (CuPc) (200 Å)/N,N′-bis(1-naphthyl)-N,N′-diphenyl-1,1′-biphenyl-4,4′-diamine (α-NPD) (600 Å)/N′-diphenyl-N,N′-tris(8-hydroxyquinoline) aluminium (Alq3) (400 Å):10-(2-benzothiazolyl)-1,1,7,7-tetramethyl-2,3,6,7-tetrahydro-1H,5H,11H-(l)benzopyropyrano(6,7,8-i, j)quinolizin-11-one (C545T) (2%)/Alq3 (200 Å)/LiF (10 Å)/Al (1000 Å). And we used both traditional glass encapsulation and thin film encapsulation (TFE) technologies to protect the device, reducing impact of vapor and oxygen. Organic film offered an excellent surface morphology, while inorganic film was nearly a perfect barrier to vapor and oxygen. Both of them constituted the encapsulation unit of TFE. According to the results of acceleration life test, the operation lifetime of device using TFE was 22% less than that of device using traditional glass cap encapsulation. So, the technology of TFE should be optimized further, and the quality of TFE needs a great improvement. There is a long way to go and a lot of hard work before realizing flexible display with OLED, but the dream will be true one day.     

Transport and luminescence phenomena in electroformed silicon nitride-based light emitting diode

Abstract

Hydrogenated amorphous silicon nitride-based heterojunction pin diode was electroformed under sufficiently high forward bias stress leading to its instant nanocrystallization at room temperature. In order to investigate the origin of the accompanying bright visible light emission, current-voltage and electroluminescence (EL) characteristics of the electroformed diode were scanned over temperature. Electrical transport mechanism was analysed in the low, medium and high electric field regimes. Temperature and field dependence of thermal activation energy were discussed. EL characteristics were studied using the spectral energy distribution and the injection current dependence of its intensity. Thermal quenching data of EL and photoluminescence intensities were compared. Finally, the relationship between the electrical transport and luminescence phenomena was attempted to be interpreted within the frame of a self-consistent model.     

A CO2 laser rapid-thermal-annealing SiOx based metal-oxide-semiconductor light emitting diode

Enhanced near-infrared (NIR) electroluminescence (EL) of a metal-oxide-semiconductor light emitting device (MOSLED) made on CO2 laser-annealed SiOx film is demonstrated.     

室内可见光通信发光二极管阵列发射性能的研究

提出了一种基于Lambert辐射模型的发光二极管光源阵列发射天线光照度计算模型,对室内可见光通信发射天线进行了优化设计.分析了光源的空间分布形式、光源间距、光源中心光束与系统光轴夹角以及空间分布层间距等因素对光照度均匀性的影响.通过仿真模拟和分析,得到了圆形阵列天线在照度均匀性和通信传输信号稳定性方面都优于相同光源数目的矩形阵列天线,并且提高了10%左右;同时得出了在满足室内照明情形下,发光二极管阵列发射天线照度均匀度随光源间距及光源中心光束与系统光轴夹角的增加均呈现出先增加后减小的变化趋势,因此,光源间距和光源中心光束与系统光轴夹角均存在最优值;照度均匀度随空间分布层间距的减小而增加,并给出了5 m×5 m×3 m普通房间内发射天线阵列设计参数的最优值,使发射性能得到了优化,同时节省光源数13%,降低了成本.这些研究为发射天线系统的设计提供了理论依据,具有实用价值.     

新型全方位反射铝镓铟磷薄膜发光二极管

提出了一种新型全方位反射铝镓铟磷(AlGaInP)薄膜发光二极管(LED)的结构和制作工艺，在这个结构里应用了低折射率的介质和高反射率的金属联合作为反光镜.用金锡合金(80Au20Sn，重量比)作为焊料把带有反光镜的AlGaInP LED外延片倒装键合到GaAs基板上(RS-LED)，去掉外延片GaAs衬底，把被GaAS衬底吸收的光反射出去.通过与常规AlGaInP 吸收衬底LEDs(AS-LED)和带有DBR的AlGaInP 吸收衬底LEDs(AS-LED(DBR))电、光特性的比较，证明新型全方位反射AlGaInP薄膜LED结构能极大提高亮度和效率.正向电流20mA时，RS-LED的光输出功率和流明效率分别是AS-LED的3.2倍和2.2倍，是AS-LED(DBR)的2倍和1.5倍.RS-LED(20mA下峰值波长627nm)的轴向光强达到194.3mcd，是AS-LED(20mA下峰值波长624nm)轴向光强的2.8倍，是AS-LED(DBR)(20mA下峰值波长623nm)轴向光强的1.6倍. 关键词： 铝镓铟磷 薄膜发光管 全方位反射镜 发光强度     

Optical design of adjustable light emitting diode for different lighting requirements

<正>Light emitting diode(LED) sources have been widely used for illumination.Optical design,especially freedom compact lens design is necessary to make LED sources applied in lighting industry,such as large-range interior lighting and small-range condensed lighting.For different lighting requirements,the size of target planes should be variable.In our paper we provide a method to design freedom lens according to the energy conservation law and Snell law through establishing energy mapping between the luminous flux emitted by a Lambertian LED source and a certain area of the target plane.The algorithm of our design can easily change the radius of each circular target plane,which makes the size of the target plane adjustable.Ray-tracing software Tracepro is used to validate the illuminance maps and polar-distribution maps.We design lenses for different sizes of target planes to meet specific lighting requirements.     

Design of optical components for a light emitting diode zoom illumination system

In this article, we report an optical design for a light emitting diode that can achieve high illumination quality using two hyperbolic reflectors. The relative movements of the reflectors and the light source produce a zoom function that can change the illumination beam from convergence to divergence. This study uses optical software ZEMAX for system simulation, and optimization was performed to select reflector parameters with the objectives of both improving floodlight uniformity and spotlight efficiency. Finally, experiments were conducted to verify the validity of the design, and the results corresponded well to the zoom illumination simulations.     

Performance enhancement of UV quantum well light emitting diode through structure optimization

Optical and Quantum Electronics - Arithmetic logic unit (ALU) is the core of any digital processing systems. For creating an all optical ALU one needs basic logic gates such as optical NOT, OR and...