同步三通道激光告警光学系统有效孔径的确定及截获能量的估算

为了确定一种同步三通道激光告警光学系统的有效孔径并估算截获能量,建立了激光辐照远场传输模型,仿真研究了远场光斑半径、单通道入瞳半径和通道间相对能量差之间的数值关系.仿真结果表明:各通道之间最大相对能量差与远场光斑中心能量密度的大小无关,在激光远场光斑边沿处各通道之间的相对能量差最大;最大相对能量差限定时,远场光斑半径越大,允许的单通道入瞳半径也越大,但相应系统截获的脉冲能量或脉冲功率却相对减小;最大能量差限定为1%,远场光斑半径分别为2.5 m,4.0 m和7.5 m时,允许的最大单通道入瞳半径分别为3 mm, 5 mm和10 mm,相应系统截获的最大脉冲能量为1.14×10-5 J,7.54×10-6 J和2.68×10-6 J,最大脉冲功率为1.63 W, 1.08 W和0.38 W.     

电泳式He-Sr+复合激光特性研究

设计制作了7 mm内径和38 cm有效激励长度的电泳式He-Sr 激光管,采用修饰Blumlein电路,通过纵向高重复率脉冲放电激励,实现了一价锶离子复合激光430.5 nm和R-M跃迁激光1.03μm的同时振荡,其中复合激光占主要成分.测量分析了复合激光输出功率与工作参量(脉冲频率,充电电源电压和氦压)的关系曲线.获得了最大激光功率819mW和56mW/cm3功率密度的实验结果.     

高效率光参量转换

用一块6.5×9×20(长度)mm KTP晶体获得625nm～3575nm的皮秒可调谐激光.能量转换效率高达30%,最大信号光峰值功率34MW.     

电泳式He-Sr+复合激光特性研究

设计制作了7mm内径和38cm有效激励长度的电泳式He-Sr⁺激光管,采用修饰Blumlein电路,通过纵向高重复率脉冲放电激励,实现了一价锶离子复合激光430.5nm和R-M跃迁激光1.03μm的同时振荡,其中复合激光占主要成分.测量分析了复合激光输出功率与工作参量(脉冲频率,充电电源电压和氦压)的关系曲线.获得了最大激光功率819mW和56mW/cm³功率密度的实验结果. 关键词： 锶离子激光 电泳 脉冲放电     

电泳式He-Sr+复合激光特性研究

设计制作了7mm内径和38cm有效激励长度的电泳式He-Sr⁺激光管,采用修饰Blumlein电路，通过纵向高重复率脉冲放电激励,实现了一价锶离子复合激光430.5nm和R-M跃迁激光1.03μm的同时振荡，其中复合激光占主要成分.测量分析了复合激光输出功率与工作参量(脉冲频率，充电电源电压和氦压)的关系曲线.获得了最大激光功率819mW和56mW/cm³功率密度的实验结果.     

基于大面积双源激光光幕的射击密集度测试技术

针对超高射频武器射频高、弹丸空间散布大、飞行速度高的特点,设计了一种大面积高精度的激光光幕靶,用于射击密集度的测试。提出了由线激光器、光源整形系统、激光检测阵列共同组成的激光光幕靶设计方案,给出了弹丸坐标的求解原理和计算模型,得出不同大小靶面的x、y坐标计算误差,并对结果进行了分析,x坐标计算误差的标准差为0.015mm,y坐标计算误差的标准差为0.134mm,证明了测试靶有很好的可拓展性。通过实弹射击验证,得到x坐标最大误差为1.91mm,y坐标最大误差为1.92mm,表明测试靶可以有效满足超高射频武器射击密集度测试需求。     

高脉冲重复频率调Q Tm,Ho:GdVO4激光器

报道了一个高效率连续波和调Q高重频两种运行方式的Tm,Ho:GdVO4激光器.Tm,Ho:GdVO4晶体尺寸4 mm×4 mm×7 mm,a轴通光,液氮制冷到100 K,由发射中心波长为793 nm的光纤耦合激光二极管端面泵浦.Tm,Ho:GdVO4激光连续波输出功率4.0 W,光光转换效率26%.声光调Q条件下输出平均高功率3.9 W,脉冲重复频率10 kHz,脉冲宽度50 ns. 通过减小声光Q开关的开启时间,激光脉冲宽度由50 ns减小至23 ns.在10 kHz重频下,测量最大脉冲能量0.39 mJ , 峰值功率7.8 kW.     

1.2 W中红外ZnGeP2光参量振荡器

报导了利用Tm,HoGdVO4激光器抽运双谐振ZnGeP2光参量振荡器实验研究.Tm(5%),Ho(0.5%)GdVO4晶体采用液氮制冷方式,工作在77 K温度条件下.以25 W波长为800 nm的光纤耦合激光二极管抽运,2 μm激光最大平均功率7 W,脉冲宽度小于30 ns, 脉冲重复频率5 kHz到20 kHz可调.非线性频率转换晶体ZnGeP2长15 mm,55?切割,OPO谐振腔为平平腔,腔长约25 mm.在5W的2 μm激光抽运下,脉冲重复频率10 kHz,实现了信号光3.7 μm及闲频光4.5 μm中红外激光输出,参量光脉冲宽度为15～17 ns,最大平均功率大于1.2 W,光-光转换效率为20%.测量参量光输出光束全宽度远场发散角4 mrad,光束质量M2因子小于3.     

1.2 W中红外ZnGeP2光参量振荡器

报导了利用Tm,Ho:GdVO4激光器抽运双谐振ZnGeP2光参量振荡器实验研究.Tm(5%),Ho(0.5%):GdVO4晶体采用液氮制冷方式,工作在77 K温度条件下.以25 W波长为800 nm的光纤耦合激光二极管抽运,2 μm激光最大平均功率7 W,脉冲宽度小于30 ns, 脉冲重复频率5 kHz到20 kHz可调.非线性频率转换晶体ZnGeP2长15 mm,55?切割,OPO谐振腔为平平腔,腔长约25 mm.在5W的2 μm激光抽运下,脉冲重复频率10 kHz,实现了信号光3.7 μm及闲频光4.5 μm中红外激光输出,参量光脉冲宽度为15～17 ns,最大平均功率大于1.2 W,光-光转换效率为20%.测量参量光输出光束全宽度远场发散角4 mrad,光束质量M2因子小于3.     

脉冲激光烧蚀材料等离子体反冲压力物理模型研究与应用

分析了脉冲激光烧蚀材料等离子体等温膨胀阶段的物理特性,建立了脉冲激光烧蚀材料等离子体压力三维方程与动力学模型.应用所建模型,数值分析了单脉冲激光烧蚀青铜金刚石砂轮等离子体相关特性,得到等离子体的反冲压力最大值870 Pa出现在约25 ns后,距离砂轮表面距离约0.05 mm处.相关条件下开展脉冲激光烧蚀青铜金刚石砂轮试验,采用高速相机观测烧蚀砂轮过程中的飞溅现象;采用光栅光谱仪测量等离子体空间发射光谱,计算了等离子体电子温度、电子密度以及反冲压力.实验表明脉冲激光烧蚀青铜金刚石砂轮等离子体反冲压力可以不计,同时也验证了气体方程与动力学模型的正确性和可行性,对脉冲光纤激光烧蚀工艺优化具有启示意义.     

全内腔绿光He-Ne激光器

采用Needle法,对全内腔绿光He-Ne激光器膜系进行设计,并给出了所设计膜系的光谱性能。利用离子溅射镀膜技术镀制了所设计的膜片并且给出了测量结果。制备了多种规格的全内腔绿光He-Ne激光器并且讨论了相关工艺。其中腔长420mm的全内腔绿光He-Ne激光器的典型输出光功率为3mW（单模）,腔长360mm的典型输出光功率为2mW（单模）,腔长240mm的典型输出光功率为1mW（单模）,腔长100mm的小短管子也能有0．1mw的出光功率。     

光场电离下玻璃微毛细管的X射线谱

利用软X射线大面积透射光栅谱仪,对超短强激光脉冲辐照下玻璃微毛细管靶的软X射线发射特性进行了研究。测得了不同的激光能量下、不同长度（3mm、6mm、9mm)的微毛细管的软X射线发射谱,并观察到随着微毛细管长度的增加,X射线发射强度增强。     

Laser action in an argon vacuum arc discharge

A transverse vacuum arc discharge has been developed. The anode cathode distance is 4 mm, the discharge length 100 mm. Gain up to 0.55% cm^?1 and a maximum laser power of 20 mW have been observed in argon at 488 nm.     

A compact high efficient diode-double-passing-pumped mid-IR Tm:YLF laser at room temperature

A new compact high efficient diode-double-passing-pumped Tm:YLF laser at room temperature is presented. Using a crystal of 3 mm × 3 mm × 12 mm 4% doping Tm:YLF and double-end-double-passing pumping cavity structure without complex optical splitter pumping system, 5.6 W CW 1907.6 nm laser is obtained at 26.2 W 792 nm pumping laser. The slope efficiency is as high as 37.8% and the spectrum width is 2 nm. The relationship between cavity length and output laser is also analyzed. Experiments verify that the highest energy and convertion efficiency can be reached by optimizing the oscillator cavity length. Finally, we used this Tm:YLF laser to pump Ho:YAG crystal at room temperature and achieved 1.65 W 2.1 μm output laser with slope efficiency 67%.     

Testifying experiment of the multi-pulse phenomena of capillary discharge soft-X-ray laser

In a capillary discharge experiment for the neon-like argon lasing, we have proposed an experimental scheme to verify that the multi-spike of X-ray diode (XRD) signal is a multi-pulse laser or is a reflection of the laser pulse in the XRD.The ceramic capillary has an inner diameter of 3mm and a length of 200mm.At the gas pressure of 28Pa and discharge current of 27kA, stable lasing has been realized.The experimental results prove that the multi-spike of XRD signal is a reflection of the electromagnetic signal produced by the laser pulse in the XRD.The improved electrocircuit scheme of the XRD to minimize the reflection phenomena is also found.     

The effects of process parameters on spatter deposition in laser percussion drilling

This paper reports on the characterisation and analysis of spatter deposition during laser drilling in Nimonic 263 alloy for various laser processing parameters using a fibre-optic delivered 400 W Nd:YAG laser. The principal findings are a large proportion of the spatter (approx. > 70%) was deposited due to the initial laser pulses (before beam breakthrough) required to drill a through-hole. Short pulse widths, low peak powers and high pulse frequencies generated smaller spatter deposition areas. At high pulse frequencies, the spatter distribution/thickness can be altered as a result of laser-ejected material interaction. Focal plane positions between −0.5 and +1.5 mm produced relatively similar spatter areas of about 14 mm². As a result of the reduction in the material removed per pulse, a longer focal length of 160 mm generated smaller areas of spatter deposition in comparison to a shorter focal length of 120 mm. In addition, a generic relationship between the spatter area and d_entrance/d_exit with increasing total laser energy has been established.     

Entwicklung leistungsfähiger Stickstofflaser mit abgeschmolzenem Laserrohr

For an increase of the laser pulse energy from longitudinally excited multiple electrodes tubes, experiments and model calculations have been accomplished. A variation of the electrode spacing in the laser tube has shown, that a maximum pulse energy could be achieved with about 40 mm electrode spacing. If barium titanat capacitors with a dielectric constant of 10000 in the pulse forming unit were applied, a voltage pulse transform occured enabling an increase of the laser power up to 50%. With a sealed off operated laser tube of 100 cm active length, a laser peak power of 600 kW and a pulse duration of 10 ns could be achieved. A tube with 200 cm active length generated a pulse power of 1.2 MW. The decrease of laser pulse energy with increasing pulse repetition rate can be explained by the decrease of impulse breakdown voltage. For an increase of the lifetime of laser tubes, appropriate technologies for the production of the tube have been developed.     

随机高斯型相位板的束匀滑特性

 针对激光系统对光束匀滑的需求,设计了高斯型连续相位板,并对其远场特性进行了研究。分别计算了相干长度为39,30,10和3 mm的高斯相位板远场光斑分布,结果显示相位板自身相关长度是决定远场能量分布的重要因素,当相干长度大于10 mm时,由于不满足各态历经条件,远场光斑分布能量分散。当相干长度小于10 mm后,由于满足各态历经条件,远场光斑能量将接近理想的高斯分布特性。通过数值计算模拟了相干长度为3 mm的连续相位板对畸变光束进行匀滑处理的过程,演示了束匀滑处理结果。通过比较匀滑前后远场光斑的能量分布,显示了畸变光束通过连续相位板后远场光斑能量分布变化情况,通过相位板后,光斑形状明显接近理想高斯分布情况。     

The Experimental Study of a 100W Copper Vapor Laser

ＴｈｅＥｘｐｅｒｉｍｅｎｔａｌＳｔｕｄｙｏｆａ１００ＷＣｏｐｐｅｒＶａｐｏｒＬａｓｅｒＣＨＥＮＬｉｎＴＡＯＹｏｎｇｘｉａｎＹＩＮＸｉａｎｈｕａＷＡＮＧＲｅｎｗｅｎ（ＳｈａｎｇｈａｉＩｎｓｔｉｔｕｔｅｏｆＯｐｔｉｃｓａｎｄＦｉｎｅＭｅｃｈａｎｉｃｓ，Ｃ...     

A guided wave monolithic resonator ruby fiber laser

Single crystal ruby fibers, cooled with liquid nitrogen, have been operated as end pumped lasers. The fiber laser is a guided wave device with a length of 15 mm and a mean diameter of 60 μm. The laser resonator structure is monolithic, consisting of an aluminium mirror coated on one fiber end face and an uncoated opposite end face serving as an output coupler. Using an argon ion laser pump source, cw output powers of several mW were obtained.