一体化光纤滤除器和端帽实现20 kW激光输出北大核心CSCD

在高功率光纤激光系统中,包层光滤除器能将光纤中包层光滤除以保证输出激光光束质量,光纤端帽通过对输出激光扩束降低输出光纤端面的光功率密度,从而保护光纤端面不受损坏,两者都是高功率光纤激光系统稳定运行的重要核心器件。将包层光滤除器和光纤端帽进行一体化设计,制备了一体化高功率光纤包层光滤除器和光纤端帽并分别应用于20 kW合束系统和单纤系统中,输出功率达到20 kW时,端帽的最高温度约为40℃,温升速率约为0.8℃/kW。     

多芯片半导体激光器光纤耦合设计

应用ZEMAX光学设计软件模拟了一种多芯片半导体激光器光纤耦合模块,将12支808nm单芯片半导体激光器输出光束耦合进数值孔径0.22、纤芯直径105μm的光纤中,每支半导体激光器功率10 W,光纤输出端面功率达到116.84W,光纤耦合效率达到97.36%,亮度达到8.88MW/(cm2·sr)。通过ZEMAX和ORIGIN软件分析了光纤对接出现误差以及单芯片半导体激光器安装出现误差时对光纤耦合效率的影响,得出误差对光纤耦合效率影响的严重程度从大到小分别为垂轴误差、轴向误差、角向误差。     

Top-hat beam Tm<Superscript>3+</Superscript>-doped fiber laser using an intracavity abrupt taper

The top-hat beam clad-pumped Tm³⁺-doped fiber laser was realized simply using an intracavity multi-mode abrupt taper. The ratio of the flat-top diameter to the spot diameter reaches 53%, with a small intensity variation less than 6%, and the top-hat beam’s half-divergence angle is only 5.3°. The fiber laser has a maximal output power of 5 W with slope efficiency of 39.7%, pumped by the 792 nm diode laser (LD). The abrupt taper is directly made on the multi-mode double-clad Tm³⁺-doped fiber near the fiber laser output end with the 0.45 ratio of taper waist diameter to fiber clad diameter, and this fiber end 4% Fresnel reflection is used to be the output coupler. The fiber laser’s high reflective coupler is an intracore multi-mode FBG, which is directly written into the multi-mode Tm³⁺-doped fiber core using femtosecond laser and phase mask, at the other fiber end. The abrupt taper has no obviously influence on the fiber laser output power, and the output laser spectrum.     

端面泵浦掺Yb3+双包层光纤激光器

从双包层光纤激光器的速率方程出发，得到了光纤中泵浦光与激光的功率分布、输出功率与泵浦功率的关系、腔镜反射率及光纤长度对输出功率的影响。研究结果表明：输出激光功率与光纤长度及后腔镜反射率有很强的依赖关系，存在一个输出功率最大的最佳光纤长度。后腔镜反射率越大，输出激光功率越小；当光纤长度较短时，在输出端放置反射镜使泵浦光高反射，可以提高输出功率和效率。通过对端面泵浦掺Yb3+双包层光纤激光器进行理论分析和实验研究，得到输出激光的中心波长为1088.3nm，斜率效率为33.7%，最大输出功率为1.75W。     

Intermodal interference induced significant frequency modulation to amplitude modulation conversion in a broadband large-mode-area fiber laser

The conversion of the FM-to-AM effect induced by intermodal interference in the broadband large-mode-area (LMA) fiber laser was first investigated theoretically and experimentally. The numerical simulation results show that the spectrum transfer functions are different at different positions of the LMA fiber end face owing to the intermodal interference, so the output broadband pulses are different. We attain the similar results in the experiment when measuring the output pulse with the single mode fiber sampling oscilloscope. Whereas there is no amplitude modulation for the output pulse when measured by the bulk detector owing to the orthogonal characteristic of the eigenmodes.     

Laser machining of micro-lenses on the end face of single-mode optical fibers

Focussing of the output beam of optical fibers is required in a variety of applications. We present a laser micro-machining technique for the fabrication of micro-lenses directly on the end face of single-mode silica fibers using a F₂-laser processing station. A uniform ablation spot is projected onto the fiber end face and steered along a trajectory of overlapping concentric circles. The lens profile is controlled by the spot size, the number of circles in the trajectory, and the scanning speed. Strong 157 nm absorption by the silica glass facilitates precise structuring without micro-crack formation in both cases. The surface quality of the fiber-lenses is characterized by AFM and SEM and reveals ∼ 100 nm rms roughness with good control of the surface profile. Optical beam profiling indicates the possibility for creating spot sizes of 1/5 the core diameter at the fiber output. PACS 42.81.Wg     

High efficient Tm3+ doped double cladding silica fiber laser with an intracavity biconical taper

A high efficient LD (laser diode) pumped Tm³⁺ doped double clad silica fiber laser with an intravacity biconical taper was reported. A biconical taper located ～3 cm from the output end of the fiber laser was fabricated by heating and stretching method with a length 1.5 cm and waist diameter ～20 µm. The slope efficiency was 49.8% with respected to the launched pump power, and the maximum output power was 1.97 W. Pre and post output laser power ratio was ～10. This fiber laser was compared with other three biconical tapered fiber lasers (the same fiber with different tapers) and a uniform geometry fiber laser. With intracavity biconical tapers, fiber lasers’ thresholds were ～1 W higher than the fiber laser without the taper (1.97 W). The pump end’s slope efficiencies of fiber lasers with tapers were 3–5% in contrast with 37.6% of the uniform one. After tapered, the pre and post laser power ratios were much higher than the un-tapered one’s, but not changed much with the launched pump power.     

Infrared-laser delivery system based on polymer-coated hollow fibers

Infrared Er : YAG laser delivery systems based on hollow fibers with an internal polymer layer has been developed. The system consists of a hollow fiber as the delivery medium, a launching coupler for effective coupling between the laser beam and the fiber, and a sealed hollow-fiber tip attached at the output end of the fiber. Fabrication process of the fiber and attachment of the delivery system is reported.     

多芯光纤激光器中共相位模式功率的提高

 以七芯光纤激光器为例，提出一种提高多芯光纤激光器总输出光功率中共相位模式所占比例的方法，即把多芯光纤激光器作为种子光源，输出信号光再经过多芯光纤放大器进行放大。基于速率方程组对激光器和放大器中的模式竞争进行了数值分析。计算表明：激光器输出端与放大器输入端之间距离存在一个最佳值，以使得放大器输出信号中低阶模式功率占总输出功率的比例最低，可以下降到小于1%。研究表明：级联放大系统可以有效增强共相位模式同时抑制低阶模式，比传统的塔耳博特腔激光器具有更好的光束质量。     

真空条件下激光诱导光纤损伤特性研究

实验研究并分析了调Q Nd:YAG 脉冲激光诱导光纤损伤特性.设计了在真空条件下全石英光纤传输1064 nm 脉冲激光实验.通过将激光注入光纤端面气压降低到10—100 Pa, 光纤端面击穿阈值提高到大气环境下的185 倍.结合光纤端面损伤形貌分析可知,光纤端面损伤主要是由于激光驻波场和烧蚀共同作用的结果,光纤端面或内部大量的缺陷降低了光纤抗激光损伤的能力.在真空条件下由于光纤端面光学击穿阈值的提高,激光诱导光纤损伤特性又表现出了另外一种损伤模式——光纤初始输入段损伤.它发生在光纤输入段附 关键词： 激光损伤 光束传输 真空 石英光纤     

窄线宽掺Yb3+双包层光纤激光器研究

 与通常的双包层光纤激光器不同，光纤前端面与二色镜拉开一个小的距离，构成了Fabry-Perot滤波器。理论分析了Fabry-Perot滤波器效应。通过调节光纤前端面与二色镜之间的距离，实现了掺Yb³⁺双包层光纤激光器的窄线宽激光输出，中心波长为1 082.79 nm，谱线宽度为0.14 nm，斜率效率为20%，最大输出功率为0.62 W。     

Generation of a compact high-power high-efficiency normal-dispersion pumping supercontinuum in silica photonic crystal fiber pumped with a 1064-nm picosecond pulse

Broadband normal dispersion pumping supercontinuum （SC） generation in silica photonic crystal fiber （PCF） is investigated in this paper. A 1064-nm picosecond fiber laser is used to pump silica PCF for the SC generation. The length of PCF is optimized for the most efficient stimulated Raman scattering process in the picosecond pump pulse region. The first stimulated Raman Stokes peak is located in the anomalous dispersion regime of the PCF and near the zero dispersion wavelength; thus the SC generation process can benefit from both a normal dispersion pumping scheme and an anomalous dispersion pumping scheme. The 51.7-W SC spanning from about 700 nm to beyond 1700 nm is generated with an all-fiber configuration, and the pump-to-SC conversion efficiency is up to 90%. In order to avoid the output fiber end face damage and increase the stability of the system, an improved output solution for the high power SC is proposed in our experiment. This high-efficiency near-infrared SC source is very suitable for applications in which average output power and spectral power density are firstly desirable.     

Output power improvement in an Yb-doped fiber laser with an additional unpumped Yb-doped fiber

Master oscillator power amplifier (MOPA) technology has been widely used in high-power or ultrashort-pulse fiber laser systems because the shape of the laser pulse can be easily adjusted. Usually, the first amplification stage of a 1064 nm fiber laser uses the core-pumped Yb-doped fiber amplifier (YDFA); however, the gain or output power is limited owing to the strong amplifier spontaneous emission (ASE) in the 1030 nm band. This paper presents the improved output power in an YDFA by inserting an additional unpumped Yb-doped fiber, which absorbs the lost backward ASE emitted from the pump end. We achieved an output power increase of more than 10% in a low-power signal, and the increase in output power decreased as the signal power increased. Moreover, the insertion of an additional unpumped Yb-doped fiber restricted the unwanted 1030 nm lasing in a low-power signal.     

掺Yb3+双包层光纤激光器的数值分析

 对掺Yb³⁺双包层光纤激光器不同参数情况下的输出功率和增益分布进行了数值模拟，分析了一端泵浦和双端泵浦方式下输出特性的差异，激光沿光纤长度方向的分布，输出功率与光纤长度、腔镜反射率及泵浦功率的关系。结果显示：两端泵浦较一端泵浦增益更加平坦，输出功率也稍高；当泵浦光波长为975nm时，输出激光功率对光纤长度更为敏感，最佳光纤长度相对于泵浦光波长为915nm时短且转化效率高；在大功率长光纤的情况下，光纤有损耗时输出功率随输出腔镜反射率的增加单调地减小，无损耗时输出功率不随输出腔镜反射率变化。     

Local-cooled watt-level Nd-doped phosphate single-mode fiber laser

Efficient and stable continuous-wave (CW) laser operation at 1053 nm in a Nd-doped phosphate single-mode fiber (Nd:PSMF) has been demonstrated experimentally. The fiber laser consisted of a 21 cm Nd:PSMF placed in a F-P cavity formed by high reflector butt-coupled to coupling end of the fiber and Fresnel reflection of the other end facet. An output power of 1.42 W and a slope efficiency of 34.1% (18.4%) with respect to absorbed pump power (incident pump power) were obtained with 808 nm diode pumping. An increment as much as 9.7 and 15.0% in slope efficiency of the input coupling efficiency and the output power, respectively, were obtained by using a local-cooling design provided by watered sealing the coupling point. The repeatable results indicate that the design, featuring fluid sealing the coupling point of the fiber laser, which was capable of offering an effective alleviation of thermal effects and an elevation of the quality of the laser cavity, could be expected to be a convenient and effective scheme to improve the performance characteristics of the non-silica fiber lasers and the high power fiber lasers, generally in free-space coupling configuration.     

Characterization of an Intra-Cavity Pumped P2O5-Doped Silica Raman Fiber Laser

We examine the characteristics of a P₂O₅-doped Raman fiber laser pumped by a double-clad ytterbium-doped fiber laser in an intra-cavity configuration. The double-clad fiber laser consists of two high reflection fiber Bragg gratings at 1092 nm, with an active length of 17 m, where the output grating is located at the end of the 400m P₂O₅-doped fiber. The Raman cavity is formed by a 1278-nm-high reflection fiber Bragg grating spliced to the double-clad fiber, and a 50% output coupler. The maximum conversion efficiency at 1278 nm with respect to the input pump power at 915 nm was 26.9%.     

基于单透镜的空间光-单模光纤耦合方法

将自由空间光耦合进单模光纤产生超连续谱的实验中,空间光与单模光纤的耦合效率是其中的一个关键问题。常采用的单透镜或显微物镜进行耦合存在耦合效率低、调整难度大、端面易损伤等问题。提出了先将自由空间的光耦合进纤芯尺寸较大的单模光纤,然后将纤芯较大的单模光纤和纤芯较小的单模光纤进行熔接。实验结果表明,改进的耦合系统耦合效率大大提高,达到60%以上,且调整难度降低,光纤端面的损伤概率降低,大大提高了超连续谱产生的效率。     

单端面透射模式长周期光栅的设计和测试

本文设计了一种单端面长周期光栅透射模式折射率传感器。首先,将2×2单模光纤耦合器输入端的一个光纤接头与光源相连接、输出端的两个光纤接头分别与光谱分析仪和长周期光栅的一个光纤接头相连接。然后,在包含长周期光栅的光纤另一个端面溅射反射银膜。最后,以一系列不同折射率的甘油水溶液为待测液体介质研究了直接透射模式与单端面镀银膜模式下长周期光栅的响应光谱的异同。实验结果表明:单端面镀银膜的长周期光栅的响应光谱仍然以透射谱的形式出现。对于同一种液体,单端面镀银膜的长周期光栅与直接透射模式的长周期光栅的响应光谱有着近乎相同的谐振波长值,但它们的光损耗存在一定的差异。在0~80%的甘油溶液中,直接透射模式下的光损耗从-12.92 dB变为-16.28 dB,再逐渐变到-13.22 dB;单端面镀银膜模式下的光损耗从-13.13 dB变为-13.74 dB,再逐渐变到-11.45dB。与直接透射模式相比,单端面镀银膜的长周期光栅的相对光损耗与甘油浓度的线性关系更加良好。本研究设计的长周期光栅测量系统采用单端面探头的方式检测环境介质,因而在测量中操作更加灵活方便,非常适合于远距离、恶劣环境或深层液体环境中的折射率测量。     

10-W cladding-pumped fiber laser with single transverse mode output

A Yb-doped double-clad fiber laser is demonstrated with a measured power output of 10.6 W and a fundamental spatial mode. The optical-to-optical conversion efficiency is 44% and the slope efficiency is 86% closed to quantum efficiency of optical conversion. In our laser system, a D-shape (340 μm/400 μm) inner cladding Yb-doped fiber is used as the gain material within the Fabry-Perot cavity. Multimode diode pump radiation is injected into the cladding through an end facet of the composite fiber.     

双包层光纤光栅选频双包层光纤激光器

双包层光纤激光器中多采用法布里珀罗(F-P)线形腔结构,谐振腔为一只二向色镜和光纤端面菲涅耳反射镜(反射率约为4％)构成,这属于一种有缺陷的腔结构,其稳定性不好,产生激光的波长很难得到有效控制,后腔镜不能精确选择激光器的输出波长,激光器的输出谱线较宽。在某些对激光波长有明确要求的应用中,该结构会受到限制。采用布拉格光纤光栅作腔镜,利用其窄带滤波特性,可以得到窄线宽的激光输出,目前报道的作为腔镜的布拉格光纤光栅为在单包层光敏光纤上制作而成,然后分别将不同反射率的光纤光栅与双包层增益光纤熔接,这给腔镜与双包层光纤之间带来很大的耦合损耗,影响了激光器的功率输出。该文报道了用相位掩模法在双包层光纤芯上写入了布拉格光纤光栅,并把此光纤光栅做为后腔镜．对长度为10m、20m的D形掺Yb^3 双包层光纤激光器进行实验研究,在1058nm附近得到稳定的窄线宽激光输出,3dB带宽为0．329nm。激光器最大输出功率为570mW。最后对实验结果进行了理论分析。