电泳式He-Sr+复合激光特性研究

设计制作了7 mm内径和38 cm有效激励长度的电泳式He-Sr 激光管,采用修饰Blumlein电路,通过纵向高重复率脉冲放电激励,实现了一价锶离子复合激光430.5 nm和R-M跃迁激光1.03μm的同时振荡,其中复合激光占主要成分.测量分析了复合激光输出功率与工作参量(脉冲频率,充电电源电压和氦压)的关系曲线.获得了最大激光功率819mW和56mW/cm3功率密度的实验结果.     

电泳式He-Sr+复合激光特性研究

设计制作了7mm内径和38cm有效激励长度的电泳式He-Sr⁺激光管,采用修饰Blumlein电路，通过纵向高重复率脉冲放电激励,实现了一价锶离子复合激光430.5nm和R-M跃迁激光1.03μm的同时振荡，其中复合激光占主要成分.测量分析了复合激光输出功率与工作参量(脉冲频率，充电电源电压和氦压)的关系曲线.获得了最大激光功率819mW和56mW/cm³功率密度的实验结果.     

碱土金属蒸气中两种不同机理的高重复率脉冲激光交替振荡现象

通过在钙、锶金属蒸气中的高重复率脉冲放电,发现钙离子和锶离子的自终止跃迁激光脉冲和碰撞辐射复合激光脉冲交替振荡的实验现象,在分析了它们激励机理异同的基础上进行了初步的实验对比研究. 关键词： 激光脉冲 交替振荡     

锶离子R—M跃迁激光和复合激光的参量研究

在9mm内径和42cm电极间距的石英放电管中，用氦气为缓冲气体，通过纵向快脉冲放电激励，对锶离子红外R—M跃迁激光和蓝色复合激光进行了系统的参量研究.分析和解释了两种谐振腔时各激光谱线输出功率与工作参量（氦压，频率和充电电源电压）的关系曲线，观察和讨论了对应的光电脉冲波形，获得了一组较好的工作参数. 关键词： 脉冲放电激励 锶离子 R—M跃迁激光 复合激光 光电脉冲波形     

锶蒸气中原子激光与离子激光的同时振荡

通过锶蒸气中的高频脉冲放电,实现了锶原子6.45μm自终止跃迁激光和锶离子1.03μm/1.09μm自终止跃迁激光的同时振荡.其中6.45μm激光最大激光平均功率为273mW.在对比实验的基础上分析和讨论了主要工作参数对这两组激光输出影响的差异.     

高重复率脉冲放电金属蒸气激光中电泳对金属蒸气分布的影响

建立了一个理论模型描述了高重复率脉冲放电金属蒸气激光中的电泳动力学过程.得到了稳态和瞬态时金属蒸气密度扩散方程的解析表达式.分别计算了高重复率脉冲放电的He-Sr⁺和He-Cd⁺激光在不同时刻金属蒸气密度的轴向分布过程.结果表明，在放电开始后约2s内即可在阴极区建立起相当均匀的轴向金属蒸气密度分布，从而确保了电泳式金属蒸气激光的稳定输出特性. 关键词： 电泳 高重复率脉冲放电 轴向金属蒸气分布 金属蒸气激光     

锶蒸气中原子激光与离子激光的同时振荡

通过锶蒸气中的高频脉冲放电,实现了锶原子6.45*!μm自终止跃迁激光和锶离子1.03*!μm/1.09*!μm自终止跃迁激光的同时振荡.其中6.45*!μm激光最大激光平均功率为273*!mW.在对比实验的基础上分析和讨论了主要工作参数对这两组激光输出影响的差异.     

Sr离子自终止和复合激光交替振荡的动力学模型

建立了一个反映高重复率脉冲放电激励的Sr离子自终止激光和复合激光交替振荡的动力学模型，得到了与实测光电脉冲波形相一致的模拟结果.给出了He-Sr放电等离子中长寿命粒子、激光上下能级粒子数密度和电子温度随时间的演化过程.分析了两种激光交替振荡的发射过程、脉冲宽度特性和粒子数反转机理，认为在放电早期和余辉期电子温度的急剧升高和降低是Sr离子自终止和复合激光实现交替振荡的关键所在. 关键词： 自终止激光 复合激光 交替振荡 动力学模型     

Sr原子M-M跃迁激光的动力学模型

建立了一个反映高频脉冲放电激励的Sr原子M-M跃迁激光的动力学模型，阐明了各激光谱线上能级的主要抽运途径：其中301μm上能级是在放电脉冲早期通过更高能级的自发辐射和激光跃迁得到布居，而另3条谱线的上能级主要是通过余辉期一价Sr离子和电子的碰撞复合以及He和三重态Sr原子的混和碰撞实现布居.定量的计算结果与实验测量结果相一致，圆满解释了各种光脉冲的时间延迟关系. 关键词： 锶原子激光 M-M跃迁 动力学模型     

锶蒸气M-M跃迁激光

通过在锶蒸气和氦混合气体中的高重复率脉冲放电,同时获得了锶原子4条谱线的激光振荡,它们对应于复三能级4d·³D_3,2,1与5p·³P⁰_2,1,0之间的多谱线跃迁,其波长分别为292μm,301μm,269μm和260μm.除了301μm激光外,均为首次报道.激光平均功率合计约10mW,相互之间的强度比为5∶4∶4∶1.在分析了相关能级特征和实验现象的基础上,对其作用机理进行了初步的探讨,建议将其分 关键词： 锶蒸气激光 自终止 M-M跃迁     

Output characteristics of a cataphoresis He–Sr recombination laser

A cataphoresis discharge tube of 7 mm inner diameter and 38 cm active length was designed and made for the He–Sr⁺ laser. The cataphoretic input of uniform distribution of strontium vapor concentrations along the active region was realized by the cataphoresis effect and the slow flowing (0.5 nl/h) of helium buffer gas. The strontium ionic recombination laser at 430.5 nm and the R–M transition laser at 1.03 μm were obtained with the modified Blumlein circuit by high-frequency longitudinal pulsed discharge. The laser components are concentrated on the 430.5 nm wavelength. Dependences of working parameters such as the pulse frequency, the supply voltage, and the helium pressure on laser output characteristics were measured and discussed. The maximum laser output power of 819 mW and specific power of 56 mW/cm³ were obtained, respectively.     

Characteristics of a Cataphoresis He-Ca+ Recombination Laser

A cataphoretic input of calcium vapour into the active volume of pulsed He-Ca^＋ laser is designed and made. The recombination laser at 373.3 nm and the R-M transition laser at 854.6 nm are achieved experimentally with modified Blumlein circuit by high-frequency longitudinal pulsed discharge. The dependences of work parameters such as the pulse frequency, the power supply voltage and the helium pressure on laser output characteristics at 373.3nm line are measured and discussed. The maximum laser output power of 136mW and the specific power of 5.9 m W/cm^3 are obtained, respectively.     

504 nm blue-green laser based on sum-frequency mixing of diode pumped Nd<Superscript>3+</Superscript> lasers

We report for the first time a continuous-wave (CW) blue-green radiation at 504 nm by intracavity sum-frequency generation of 946 nm Nd:YAG laser and 1080 nm Nd:YAlO₃ (Nd:YAP) laser. Using type-I critical phase matching LiB₃O₅ (LBO) crystal, 504 nm blue-green laser was obtained by 946 and 1080 nm intra-cavity sum-frequency mixing, and output power of 215 mW was demonstrated. At the output power level of 215 mW, the output power stability is better than 4.7% and laser beam quality M² factor is 1.21.     

Diode-pumped Nd:CaYAlO<Subscript>4</Subscript>-KTP intracavity-doubled green laser at 540 nm

It is reported that efficient continuous-wave (CW) green laser generation at 540 nm in a KTP crystal at type-II phase matching direction performed with a diode-pumped Nd:CaYAlO₄ laser. With incident pump power of 18.2 W, output power of 324 mW at 540 nm has been obtained using a 5 mm-long KTP crystal. At the output power level of 324 mW, the output stability is better than 2.8%. The beam quality M ² values were equal to 1.34 and 1.22 in X and Y directions, respectively.     

Diode-pumped Nd:YCOB self-frequency-doubling red laser at 666 nm

It is reported that efficient continuous-wave (CW) self-frequency-doubling red laser at 666 nm performed with a diode-pumped Nd³⁺:YCa₄O(BO₃)₃ (Nd:YCOB) laser. With a diode pump power of 14.3 W, TEM₀₀ mode red laser at 666 nm of 570 mW is obtained. At the output power level of 570 mW, the output stability is better than 3.5%. The beam quality M² value is about 1.25. To the best of our knowledge, this is the highest power laser at 666 nm generated by self-frequency doubling of a diode pumped Nd:YCOB laser.     

All-solid-state Yb:KYW-LBO blue-green laser at 500 nm

It is reported that efficient continuous-wave (CW) blue-green laser generation at 500 nm in a LBO crystal at type-I phase matching direction performed with a Ti:sapphire laser-pumped Yb:KYW laser. With incident pump power of 8.7 W, output power of 138 mW at 500 nm has been obtained using a 10 mm-long LBO crystal. At the output power level of 138 mW, the blue-green output stability is better than 2.8%. The blue-green beam quality M ² values were equal to 1.25 and 1.18 in X and Y directions, respectively.     

Diode-pumped continuous-wave Nd<Superscript>3+</Superscript>:YAlO<Subscript>3</Subscript> intracavity-doubled red laser

It is reported that efficient continuous-wave (CW) red laser generation at 670 nm in a LBO crystal at type-I phase matching direction performed with a diode-pumped Nd³⁺:YAlO₃ (Nd:YAP) laser. With incident pump power of 15.6 W, output power of 273 mW at 670 nm has been obtained using a 10 mm-long LBO crystal. At the output power level of 273 mW, the output stability is better than 3.7%.     

A cw uv copper hollow cathode laser in the 260 nm region

A cw uv copper hollow cathode laser is described, which could be operated for a longer time duration with an output power of 7 mW in the 260 nm region. A double-cathode configuration with a protection for the mirrors from metal-vapour deposition is presented. Characteristics of the laser output power, the spontaneous emission, and the ion densities in the negative glow were measured as depending on the discharge current, the neon gas pressure, and the size of the cathode slit. The observed saturation of the laser output power at high discharge current (1 A/cm²) and the optimum slot size are discussed.     

Intracavity sum-frequency generation of CW blue light in Nd:LuVO<Subscript>4</Subscript> laser

We report for the first time a continuous-wave (CW) blue laser emission by sum-frequency mixing in Nd:LuVO₄ crystal. Using type-I critical phase-matching (CPM) LBO crystal, a blue laser at 493 nm is obtained by 1066 and 916 nm intracavity sum-frequency mixing. The maximum laser output power of 520 mW is obtained when an incident pump laser of 18.2 W is used. At the output power level of 520 mW, the output stability is better than 2.8%. The beam quality M ² value is are about 1.22 and 1.31 in both horizontal and vertical dimensions respectively.     

Diode-Pumped Nd:CNGG-LBO CW sum-frequency mixing blue-green laser at 497 nm

We report for the first time a continuous-wave (CW) blue-green laser emission by sum-frequency mixing in Nd:CNGG crystal. Using type-I critical phase-matching LBO crystal, a blue-green laser at 497 nm is obtained by 1061 and 935 nm intracavity sum-frequency mixing. The maximum laser output power of 232 mW is obtained when an incident pump laser of 18.2 W is used. At the output power level of 232 mW, the output stability is better than 3.67%. The beam quality M ² value is are about 1.26 and 1.38 in both horizontal and vertical dimensions respectively.