Multi-wavelength generation using a bismuth-based EDF and Brillouin effect in a linear cavity configuration

The generation of a multiple wavelength source using a bismuth-based erbium-doped fiber (Bi-EDF) in a linear cavity configuration is demonstrated. The configuration uses a pair of optical circulators at the input and output ends of the cavity to form a resonator for multi-wavelength generation in conjunction with optical couplers to inject the Brillouin pump (BP) and to tap the output at the two ends. The Brillouin erbium fiber laser (BEFL) comb with a 2.15 m of Bi-EDF has a wavelength spacing of 0.09 nm and operates in long-wavelength (L-) band region. A stable output laser comb of 50 lines is obtained at a BP of 1568.2 nm and 5 dBm and two 1480 nm pumps at 120 mW. The injected BP wavelength and power as well as the 1480 nm pump powers have a great effect on the number of lines and output power of the BEFL. This configuration is compact due to the use of the significantly shorter Bi-EDF as the linear gain medium, and can be made more compact by replacing the single-mode fiber with highly non-linear fibers such as holey fibers.     

Bismuth-based erbium-doped fiber as a gain medium for L-band amplification and Brillouin fiber laser

Bismuth-based erbium-doped fiber (Bi-EDF) is demonstrated as an alternative medium for optical amplification and nonlinear applications. The bismuth glass host provides the opportunity to be doped heavily with erbium ions to allow a compact optical amplifier design. The bismuth-based erbium-doped fiber amplifier (Bi-EDFA) is demonstrated to operate at wavelength region from 1570 to 1620 nm using only a 215 cm long of gain medium. The maximum gain of 15.8 dB is obtained at signal wavelength of 1610 nm with the corresponding noise figure of about 6.3 dB. A multi-wavelength laser comb is also demonstrated using a stimulated Brillouin scattering in the 215 cm long Bi-EDF assisted by the 1480 nm pumping. The laser generates more than 40 lines of optical comb with a line spacing of approximately 0.08 at 1612.5 nm region using 152 mW of 1480 nm pump power.     

铋基掺铒光纤放大器中放大自发辐射处理研究

分别设计了一个带光隔离器和一个带光环形器的复合型宽带铋基掺铒光纤放大器(Bi-EDFA),理论上研究了Bi-EDFA中对于后向传输放大自发辐射(ASE)的处理对放大器性能的影响。研究表明,在C+L波段多波长信号同时输入情形下,通过在铋基掺铒光纤中插入一个光隔离器抑制后向传输的ASE,可以提高放大器各波长信号增益,降低噪声系数。利用一个光环形器引导后向传输的ASE去泵浦一段未抽运的低掺杂铋基掺铒光纤,可以显著地提高放大器长波段信号增益,而噪声系数只是略有增加,理论研究与报道的实验结果达到了比较好的一致。研究结果对于新型宽带Bi-EDFA的设计和应用具有一定实际指导意义。     

Generation of multi-wavelength erbium-doped fiber laser by using MoSe_2 thin film as nonlinear medium and stabilizer

We experimentally demonstrate the application of MoSe2 thin film as a nonlinear medium and stabilizer to generate a multi-wavelength erbium-doped fiber laser. The cooperation of a photonic crystal fiber and a polari?zation-dependent isolator induces unstable multi-wavelength oscillations based on the nonlinear polarization rotation effect. A MoSe2 thin film is further incorporated into the cavity to achieve a stable multi-wavelength.The laser generates 7 lasings with a constant spacing of 0.47 nm at a pump power of 250 mW. The multi?wavelength erbium-doped fiber laser is stable with power fluctuations of less than 5 dB over 30 min.     

基于半导体光放大器的可调谐多波长光纤激光器

报道了一种新型环形腔可调谐多波长光纤激光器，腔内以半导体光放大器为增益介质，利用高双折射光纤构成的高双折射环形镜的滤波特性，在室温下，获得了基本符合ITU-T标准100GHz的17个波长以上的稳定多波长输出.各信道峰值功率差小于6 dB，线宽小于0.102 nm，信噪比大于25 dB.通过调节高双折射环形镜内的偏振控制器状态实现了这一组波长整体在50GHz范围内连续可调谐.并利用实验方法，对该光纤激光器应用于掺铒光纤放大器对多信道放大性能测试的可行性进行了初步探讨.     

Broadly tunable multiwavelength fiber laser with bismuth-oxide EDF using large effective area fiber

A multiwavelength laser comb using 2.49 m Bismuth-oxide erbium-doped fiber (Bi-EDF) with different lengths of large effective area fiber (LEAF) in a ring cavity configuration is realized. The Bi-EDF is used as the linear gain medium and LEAF is used as the non-linear gain medium for stimulated Brillouin scattering. Out of the four different lengths, the longest length of 25 km LEAF exhibits the widest tuning range of 44 nm (1576 to 1620 nm) in the L-band at 264 mW pump power and 5 mW Brillouin pump power. In addition, a total of 15 output channels are achieved with total average output power of −8 dBm from this laser structure. All Brillouin Stokes signals exhibit high peak power of above −20 dBm per signal and their optical signal-to-noise ratio of greater than 15 dB.     

Multi-wavelength erbium-doped fiber laser using four-wave mixing effect in doped fiber

We demonstrate a multi-wavelength erbium-doped fiber laser (EDFL) using erbium gain and four-wave mixing (FWM) effect in a piece of erbium-doped fiber (EDF) with high erbium ion concentration. The EDF has a pump absorption rate of 24.6 dB/m at 979 nm and is bi-directionally pumped by 980-nm laser diodes. FWM effect redistributes the energy of different oscillating lines and causes multi-wavelength operation. The laser generates more than 22 lines of optical comb with a line spacing of approximately 0.10 nm at the 1569-nm region using only 1.5-m-long EDF.     

室温下稳定的多波长掺铒光纤激光器的研究

通过在线形谐振腔中引入一段缠绕在压电陶瓷上的单模光纤作为正弦相位调制器,使得激射波长的损耗不固定,抑制由于掺铒光纤的均匀展宽效应引起的模式竞争,从而避免了在室温下不稳定的单波长激射,实现了多波长掺铒光纤激光器的稳定输出。为了获得平坦的多波长输出,在谐振腔里使用了一个损耗峰位于1530nm处的长周期光纤光栅,以获得较为平坦的增益谱。通过两个3dB耦合器制成的反射型梳状滤波器的滤波作用,实验中观察到稳定的多波长激射,相邻波长间隔约为0．45nm。中心9个波长的输出功率平坦度为10dB,边模抑制比大于25dB。     

A unidirectional room temperature multi-wavelength fiber ring laser without isolator

A simplified ring cavity for achieving a unidirectional room temperature multi-wavelength erbium-doped fiber ring laser without optical isolator is demonstrated. The fiber ring cavity is built in such a way that the optical fields propagating in two directions suffer different losses caused by one sampled fiber Bragg grating. Furthermore, simultaneous multi-wavelength lasing with 0.8-nm intervals is demonstrated with sinusoidal phase modulation just before the sampled fiber Bragg grating to prevent single-wavelength lasing and unstable wavelength oscillation.     

Waveband switchable multi-wavelength erbium-doped fiber ring laser based on wavelength-dependent polarization rotation mechanism

A waveband switchable multi-wavelength erbium-doped fiber ring laser based on wavelength-dependent polarization rotation mechanism and birefringence-based in-line comb filter is proposed and demonstrated. The two lasing wavebands, around 1530 and 1560 nm region, can be efficiently switched by simply rotating the polarization controllers (PCs). The channel spacing is 0.4 nm which was determined by the length of polarization maintain fiber (PMF) used in the experiment. The experimental results show that the waveband switchable is an intrinsic feature of multi-wavelength fiber ring lasers by incorporating a passive polarizer in the laser cavity.     

An Enhanced Bismuth-Based Brillouin/Erbium Fiber Laser with Linear Cavity Configuration

A multi-wavelength Brillouin/erbium-doped fiber laser (BEFL) which operates in 1594 nm region is demonstrated using a 215 cm long Bismuth-based EDF and SMF. Two optical circulators were used at the output ends of the system to form a linear cavity to produce a cascaded Brillouin Stokes and anti-Stokes. A stable output laser comb of more than 20 lines was obtained with a spacing of approximately 0.089 nm at a Brillouin pump power of 4 dBm and two 1,480-nm pumps at powers of 100 mW. The number of lines is relatively higher compared with the ring cavity BEFL.     

基于增益光纤长度优化的双波长运转掺铒光纤锁模激光器

构建了可自启动的双波长运转掺铒光纤锁模激光器.通过优化增益光纤长度,利用掺铒光纤在1530nm附近的再吸收效应调节激光器的增益谱,使激光器在1530nm和1560nm附近具有相同的增益强度.实验中采用31cm掺铒光纤作为增益光纤,以透射式半导体可饱和吸收体作为锁模器件,实现了自启动双波长锁模运转.激光器锁模输出重复频率为58.01MHz,信噪比为58.2dB,最高输出功率为4.8mW.锁模输出的光谱在1532.4nm和1552.3nm处具有两个强度接近的谱峰,谱峰间距约为20nm.该激光器无需手动调节即可实现双波长运转,更便于实际使用.     

Multi-wavelength bismuth-based erbium-doped fiber laser based on four-wave mixing effect in photonic crystal fiber

A stable multi-wavelength erbium-doped fiber laser based on four-wave mixing (FWM) in a photonic crystal fiber (PCF) is demonstrated in this paper. The phase matching condition for four-wave mixing in the photonic crystal fiber has been enhanced using a seed signal and a polarisation controller to control the states of polarisation in the ring laser cavity. At a maximum pump power of 1480 nm, 5 lines are observed with nearly 2.15 nm spacing between the lines, and with a signal to noise ratio of more than 20 dB. The number of channels and wavelength spacing can be controlled by varying the output coupler ratio.     

A tunable multi-wavelength Brillouin–erbium fiber laser with fourfold Brillouin frequency spacing

We have experimentally demonstrated a tunable multi-wavelength Brillouin–erbium fiber laser with over 40 GHz spacing utilizing two cascaded double Brillouin-frequency-spacing cavities. In this laser configuration, two segments of 25 km-long single-mode fibers are used as Brillouin gain medium in each ring cavity, and a segment of 8 m-long erbium-doped fiber with 980 nm pump is employed to amplify Brillouin pump (BP). At BP wavelength of 1550 nm, BP power of 8.3 dBm (6.8 mW) and the maximum 980 nm pump power of 27.78 dBm (600 mW), seven output channels with fourfold Brillouin-frequency spacing, and the tuning range of 15 nm from 1545 to 1560 nm are achieved. The proposed multi-wavelength Brillouin–erbium fiber laser has wide applications, such as in microwave signal generation and optical communications.     

Tunable multi-wavelength fiber laser based on a polarization-maintaining erbium-doped fiber and a polarization controller

A stable and tunable multi-wavelength fiber laser with a polarization-maintaining erbium-doped fiber (PM-EDF) and a polarization controller (PC) is proposed and demonstrated. A homemade PM-EDF incorporated in the ring cavity is used as the gain medium. Simultaneous multi-wavelength oscillation is achieved at room temperature. The theory of the PM-EDF and PC to suppress the wavelength competition is described in detail. The 3 dB bandwidth is less than 0.01 nm. The power fluctuation and wavelength shift are measured to be less than 0.5 dB and 0.05 nm over 32 min. The wavelength tuning between single-, double-, triple-, and four-wavelength is realized.     

Performance of a wavelength-tunable erbium-doped fiber laser using a Sagnac interferometer

We experimentally demonstrate a wavelength-tunable erbium-doped fiber laser that is composed of a ring cavity and a single-mode fiber Sagnac interferometer in a new and simple arrangement. We find that the fiber laser output wavelength is tunable by adjusting the filter effect of the Sagnac fiber loop through a fiber polarization controller set there. The quasi-single-wavelength continuously tunable laser outputs could be achieved within some wavelength range. The multi-wavelength laser outputs could also be observed under some appropriate settings of the polarization controller. A theoretical demonstration of the wavelength tunability about the transmission-type Sagnac loop filter has also been achieved using the Jones calculus theory.     

大功率高效率掺铒超荧光光纤光源及其应用

采用光纤反射环镜和双程后向结构,得到了最大输出功率30.6 mW、光光转换效率42.0%的大功率、高效率全光纤掺铒超荧光光源（SFS）.利用串接光纤光栅（FBG）和光纤型F-P腔,对其进行光谱分割,得到了稳定的多波长输出.实验结果和探讨对光谱分割多波长光源的研制具有指导意义.     

Investigation on stimulated Brillouin scattering characteristics in a highly doped Bismuth-based Erbium-doped fiber

Stimulated Brillouin scattering (SBS) characteristics in a 49 cm long highly doped Bismuth-based Erbium doped fiber (Bi-EDF) is investigated in the ring and linear cavity configurations. At Brillouin pump (BP) power of 6 dBm, the Brillouin laser peak power of the optimized ring Brillouin Erbium fiber laser (BEFL) is obtained at 23 dB higher than the peak power of the conventional linear cavity at an up shifted wavelength of 0.08 nm. This Bi-EDF ring cavity operates at nearly 1563 nm wavelength region, which is up-shifted by 0.08 nm from the Brillouin pump wavelength with the side mode suppression ratios (SMSR) of 29 and 23 dB in the forward and backward directions, respectively.     

Switchable multi-wavelength erbium-doped fiber laser based on a four-mode FBG

We propose a switchable multi-wavelength erbium-doped fiber laser based on a four-mode fiber Bragg grating(FBG). The four-mode FBG is fabricated in a hydrogen pre-loaded fiber by the phase mask method, which can support four linearly polarized modes around 1550 nm. The five operation wavelengths are at 1547.5, 1546.8,1546.0, 1545.1, and 1544.2 nm, respectively. Through adjusting the polarization state and the lateral offset coupling in cavity, the laser can be switched into the operation state of single, dual, or triple wavelengths. The proposed laser has the advantages of simple configuration, stable operation, and easy adjustment.     

基于多波长类噪声脉冲的掺铒光纤激光器

报道了一种基于多波长类噪声脉冲的被动锁模掺铒光纤激光器。采用980 nm半导体激光器作为泵浦源，2.5 m长的掺铒光纤作为增益介质。锁模机制为非线性放大环形镜(NALM)。通过自相关迹证明输出脉冲为类噪声脉冲。该类噪声脉冲的光谱3 dB带宽可达17.2 nm，边模抑制比为47.7 dB，重复频率为5.434 MHz，单脉冲能量为7.9 nJ。为了实现平坦的多波长输出，在NALM结构中加入Sagnac环干涉仪，获得了最大波长数为5的平坦多波长类噪声脉冲，平坦度为1.995。