H_3PW_(12)O_(40)/MCM-48的制备及其光催化降解农药(英文)

以介孔分子筛MCM-48为载体,采用水热法制备了负载磷钨酸H3PW12O40(HPW)的多金属氧酸盐催化剂HPW/MCM-48。利用傅里叶变换红外光谱(FT-IR)、小角度X射线粉末衍射(XRD)、氮气吸附检测和高分辨透射电子显微镜(HRTEM)对其结构进行了表征,并以农药吡虫啉和百草枯为对象,考察了所制备的HPW/MCM-48的光催化降解活性。结果表明,采用水热法制备的催化剂保持了MCM-48的介孔分子筛结构和HPW的Keggin结构,比表面积783.35m2·g-1,孔体积1.46cm3·g-1,平均孔径2.76nm,相比于母体HPW,HPW/MCM-48的比表面积大大增加;在365nm紫外光下反应14h后,20mg剂量HPW/MCM-48催化剂能使50mL,10mg·L-1吡虫啉和百草枯的降解率分别达57.38%和63.79%,而HPW对两种农药的降解率在25%左右,空白组降解率均低于5%,说明负载后HPW对两农药的降解活性显著增强。动力学考察表明,HPW/MCM-48对农药降解过程符合一级动力学方程,对吡虫啉和百草枯这两种农药的降解速率常数Ka分别为0.089和0.117h,半衰期t1/2为7.8和5.9h。     

多酸-介孔分子筛复合材料的制备、表征及光催化活性

采用浸渍法将具有光催化活性的多金属氧酸盐(polyoxometalate,POM)磷钨酸和硅钨酸负载到介孔分子筛MCM-41,制备了H3PW12O40/MCM-41和H4SiW12O40/MCM-41两种复合材料,以红外光谱(FT-IR)、X射线衍射(XRD)、N2吸附、高分辨透射电镜(HRTEM)等分析手段对所合成的多酸-分子筛复合材料进行了表征,并以农药百草枯的光催化降解考察了复合材料的光催化活性。所合成的复合材料同时保留了母体多酸的Keggin特征结构和载体MCM-41分子筛均匀的六方孔道结构,比表面积超过200m2.g-1。用于农药百草枯的光催化降解实验表明,两种复合材料均具有较高的光催化活性。在365nm紫外光辐照下,以H3PW12O40/MCM-41和H4SiW12O40/MCM-41为催化剂催化反应14h后,百草枯(10mg.L-1)的降解转化率分别达到92.0%和87.6%,反应符合一级化学动力学模型,半衰期分别为3.7和4.6h。     

ZnO/MCM-41复合材料的制备及其光谱性质

以硅酸钠(NaSiO3·9H2O)为硅源,三甲基十六烷基溴化铵(CTAB)为模板剂在碱性条件下水热合成介孔分子筛MCM-41,然后以其为主体,采用锌盐浸渍-灼烧的方法.在介孔分子筛MCM-41上负载了氧化锌(ZnO)纳米微粒,并通过扫描电子显微镜,红外光谱(1R).紫外可见吸收光谱(UV-Vis),N2-吸附脱附和荧光光谱等手段对产品进行了系列表征.结果表明,分子筛平均直径约为1.7μm,对不同温度下灼烧后得到的ZnO/MCM-41组装体的光谱性质进行研究表明介孔分子筛MCM-41的尺寸所限,制备出的ZnO粒子粒径小于2 nm.量子尺寸效应使得ZnO/MCM-41组装体中的ZnO纳米粒子的紫外可见吸收光谱及荧光光谱均发生蓝移.通过红外光谱分析得知ZnO负载到MCM-41上并没有改变介孔分子筛原有的骨架结构.     

(纳米MCM-41)-CdS主-客体复合材料的制备及光学性质

以水热法制备了纳米微粒MCM-41分子筛，通过离子交换法将Cd(II)交换到分子筛中，然后采用硫代乙酰胺作硫化氢前驱体对(MCM-41)-Cd进行硫化，制备出主-客体复合材料(MCM-41)-CdS．化学分析表明，客体成功地组装到分子筛中．粉末X射线衍射结果表明，组装过程并未破坏所制备的主-客体材料中分子筛的骨架，分子筛骨架完整且结晶度仍然很高．红外光谱表明所制备材料骨架保持完好．低温N2吸附-解吸附研究表明，相对于MCM-41分子筛主体所制备的复合材料孔体积、孔尺寸及比表面积降低，表明客体在分子筛孔道内组装成功．制备的主-客体复合材料固体扩散漫反射吸收光谱相对于CdS体相呈现某些蓝移，说明客体处于分子筛孔道内，也表明分子筛主体对纳米硫化镉客体表现出明显的立体限域效应．(纳米MCM-41)-CdS及(微米MCM-41)-CdS样品呈现明显发光．     

荧光光谱法研究左氧氟沙星与MCM-41的相互作用

采用微波辅助水热法制备介孔分子筛MCM-41,并用浸渍法将左氧氟沙星(LVFX)组装在MCM-41均一的六方形孔道中,制备出新型载药复合物LVFX/MCM-41。用粉末X射线衍射(XRD)、低温氮吸附、傅里叶变换红外光谱(FTIR)及差热-热重(TGA-DTA)分析对MCM-41以及LVFX/ MCM-41复合物进行表征,合成的介孔分子筛MCM-41的孔径为2.382 nm,比表面积为1 015 m2·g-1。对MCM-41、LVFX/MCM-41、LVFX(固态)及LVFX(溶液)的荧光光谱研究结果显示,LVFX/MCM-41的荧光光谱比组装前发生明显红移,表明MCM-41孔道内表面的羟基和LVFX形成氢键,羟基上的电子云向LVFX分子上的吸电子基团转移;同时MCM-41和LVFX之间形成新环,使电子云能在更大的环上移动,药物分子的共轭体系扩大,荧光光谱峰红移。MCM-41与左氧氟沙星之间强的相互作用为研发以MCM-41为载体的新型释药系统提供了理论依据。     

HPA/MCM-48对水溶性染料的光催化降解

采用浸渍法制备了MCM-48分子筛负载硅钨酸催化剂(HPA/MCM-48),通过红外光谱的方法对试样进行了表征;以紫外灯为光源,研究了HPA/MCM-48对亚甲基蓝、甲基紫、罗丹明B等3种水溶液的光催化脱色性能;讨论了催化剂用量、反应时间等因素对甲基紫降解效果的影响。实验结果表明HPA/MCM-48对染料的最佳催化条件为,10mg/L染料在紫外灯照射下,催化剂用量1.67g/L,光照时间2h;其对甲基紫的降解效果优于对亚甲基蓝和罗丹明B。     

Ni_2P/介孔分子筛催化剂的原位漫反射红外光谱研究

以介孔分子筛MCM-41,MCM-48,SBA-15,SBA-16为载体,硝酸镍为镍源,磷酸氢二铵为磷源,通过浸渍法制备了含有磷化镍前体的介孔分子筛样品,然后在氢气气氛中进行程序升温还原,得到了磷化镍/介孔分子筛催化剂.采用原位漫反射红外光谱法,用CO作为探针分子,对样品的吸附特征进行了研究.结果表明,在介孔分子筛表面CO存在着较弱的物理吸附.在Ni2P/MCM-41催化剂样品表面有四种CO的吸附态:(1)在2055cm-1处形成的Ni(CO)4物种的吸附,(2)在2 091cm-1处的配位不饱和Niδ(0<δ<1)物种上的吸附,(3)在2 127 cm-1处的Ni+物种上的吸附,(4)在2 198～2 202 cm-1范围内的P物种上的吸附.在Ni2P/MCM-48,Ni2P/SBA-15,Ni2P/SBAZ-16催化剂样品表面有二种CO的吸附态:在2 051～2 055cm-1处的Ni(CO)4吸附和在2 093～2 096 cm-1处的配位不饱和Niδ+(0<δ<1)物种上的吸附.     

超声波酸性体系下MCM-41的合成及表征

以十六烷基三甲基溴化铵(CTAB)为模板剂,正硅酸乙酯(TEOS)为硅源,以超声波为辅助手段于酸性介质中制备出了MCM-41介孔分子筛,采用XRD、TEM、FTIR等手段对样品进行了分析表征.结果表明,所合成样品具备MCM-41所特有的六方排列的一维孔道结构和较高的有序度,所合成的MCM-41平均粒径为11nm,孔径约为2.7nm.     

生物油催化裂解转化制取三苯

通过不同孔特征的分子筛(HZSM-5、HY沸石和MCM-41)实现生物油催化转化为三苯(苯、甲苯和对甲苯). 基于三苯的产率和选择性,芳香化合物逐次降低顺序为: HZSM-5>MCM-41>HY沸石.用HZSM-5催化裂解生物油产生芳香化合物的最大产率为33.1%,选择性为86.4%. 研究了反应条件对生物油催化裂解的影响,结合催化剂表征结果,讨论了催化剂的结构与性能之间的关系.     

用不同类型的分子筛催化剂催化转化生物油制烯烃

研究了用一系列不同类型的分子筛催化剂催化转化制取低碳烯烃的过程,测试的催化剂包括HZSM-5、MCM-41、SAPO- 34和Y型分子筛．按照低碳烯烃的绝对收率和选择性,催化剂的活性排序为：HZSM-5>SAPO-34>MCM-41>Y型分子筛．研究表明,使用HZSM-5分子筛催化剂,获得的生物油最大低碳烯烃收率约为0.22 kg/(kg生物油),低碳烯烃的选择性约为50%,且生物油几乎实现完全转化．同时还研究了反应条件对生物油制低碳烯烃的影响．为了弄清催化剂结构与和低碳烯烃形成之间的关系,对相关催化剂进行了详细表征,对生物油热裂解和催化裂解过程进行了详细比较．     

Synthesis of multi-wall carbon nanotubes by the pyrolysis of ethanol on Fe/MCM-41 mesoporous molecular sieves

Ordered hexagonal arrangement MCM-41 mesoporous molecular sieves were synthesized by the traditional hydrothermal method, and Fe-loaded MCM-41 mesoporous molecular sieves (Fe/MCM-41) were prepared by the wet impregnation method. Their mesoporous structures were testified by X-ray diffraction (XRD) and the N₂ physical adsorption technique. Carbon nanotubes (CNTs) were synthesized by the chemical vapor deposition (CVD) method via the pyrolysis of ethanol at atmospheric pressure using Fe/MCM-41 as a catalytic template. The effect of different reaction temperatures ranging from 600 to 800 ^°C on the formation of CNTs was investigated. The resulting carbon materials were characterized by various physicochemical techniques such as transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), and Raman spectroscopy. The results show that multi-wall carbon nanotubes (MWCNTs) with an internal diameter of ca. 7.7 nm and an external diameter of ca. 16.9 nm were successfully obtained by the pyrolysis of ethanol at 800 ^°C utilizing Fe/MCM-41 as a catalytic template.     

Microwave synthesis and textural property of europium substituted mesoporous molecular sieves

Using cetyltrimethyl ammonium bromide (CTAB) as the template and sodium silicate as the silicon source, the MCM-41 mesoporous molecular sieves with Eu incorporated in the framework were synthesized under microwave irradiation condition and the influence of the Si/Eu molar ratio on the crystalline structure, textural properties and the long-range ordering of the resulting sample was investigated by various physicochemical techniques such as X-ray diffraction (XRD), transmission electron microscope (TEM), diffuse reflectance ultraviolet-visible spectroscopy (UV-vis), thermal gravimetric-differential scanning calorimeter (TG-DSC) and N₂ physical adsorption. The results of N₂ adsorption and XRD reveal that the synthesized sample has the ordered hexagonal mesoporous structure. UV-vis spectra provide the strong evidences that most of europium ions were incorporated into the framework of the MCM-41 sample. The crystalline structure, textural properties and mesoporous ordering of the resultant mesoporous materials are related to the amount of europium incorporation. Small amount europium incorporated into the silica-based MCM-41 does not strongly modify the structure of mesoporous molecular sieve. An increase of the Eu content in sample led to reduction of the specific surface area and the deterioration of the long-range ordering.     

Effect of the Si/Ce molar ratio on the textural properties of rare earth element cerium incorporated mesoporous molecular sieves obtained room temperature

Rare earth Ce-incorporated MCM-41 mesoporous molecular sieves (CeMCM-41) were synthesized via a direct and nonhydrothermal method at room temperature from sodium silicate and ammonium cerium (IV) nitrate as raw materials. Cetyltrimethyl ammonium bromide (CTAB) was used as a template. The resultant samples were characterized by means of powder X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FT-IR), diffuse reflectance ultraviolet–visible spectroscopy (UV–vis) and N₂ physical adsorption, respectively. The effect of the Si/Ce molar ratio on the crystalline structure and textural properties of CeMCM-41 was also investigated. The experimental results show that ordered CeMCM-41 mesoporous molecular sieves were successfully synthesized at room temperature and the resultant mesoporous materials have specific surface areas in the range of 594–1369 m²/g and average pore sizes in the range of ca. 2.5–2.8 nm. It has been found that the structural properties are strongly related to the amounts of cerium incorporation. When the cerium content increased in the samples, the intensity of the peak (1 0 0) was gradually reduced, and the surface area and structural regularity were diminished.     

Impact of nanoconfinement on the diisopropylammonium chloride (C6H16ClN) organic ferroelectric

The dielectric studies of diisopropylammonium chloride (DIPAC) nanoparticles embedded into opal and MCM-41 silica matrices are presented. It is shown that the ferroelectric phase transition shifts to low temperatures and broadens for DIPAC within the opal pores compared to bulk. The thermal hysteresis of the transition increases under opal nanoconfinement. No anomalies of the permittivity relevant to the ferroelectric transition are observed for DIPAC within the MCM-41 molecular sieves likely due to formation of the amorphous phase.     

Dielectric properties of mixed NaNO2-KNO3 ferroelectrics in nanoporous silicate matrices

Physics of the Solid State - Results of dielectric studies of MCM-41 molecular sieves with mesoporous channels (37.0 and 24.3 Å in size) loaded with the ferroelectric (NaNO2)1 ? x (KNO3)...     

Hydrocarbon oxidation catalyzed by vanadium polyoxometalate supported on mesoporous MCM-41 under ultrasonic irradiation

Vanadium polyoxometalate (PVMo) supported on mesoporous MCM-41, MCM-41-NH(2), as efficient and heterogeneous catalysts, with large surface area, for hydrocarbon oxidation with hydrogen peroxide is reported. Oxidation of the alkenes and alkanes gave product selectivities, which are similar to those observed for corresponding homogeneous catalyst. PVMo-MCM was prepared by introduction of PVMo into the mesoporous molecule sieves of MCM-41 by impregnation and adsorption techniques. The samples were characterized by X-ray diffraction (XRD), thermal gravimetric-differential thermal analysis (TG-DTA), FT-IR, scanning electron microscopy (SEM), UV-Vis and cyclic voltametry (CV). Ultrasonic irradiation has a particular effect on MCM-41 structural uniformity and reduced the reaction times and improved the product yields. In addition, the solid catalysts could be recovered and reused several times without loss of its activity.     

Dielectric and NMR Studies of the superionic conductor AgI embedded in mesoporous silicate matrices

This paper reports on the results of studies of small particles of the superionic conductor AgI embedded in MCM-41 and SBA-15 molecular sieves with different sizes of pores (channels). The studies are performed by the dielectric and nuclear magnetic resonance techniques. The temperature of the superionic phase transition is shown to increase monotonically with decreasing pore size. The enthalpy of activation of the ion motion in β-AgI in restricted geometry is determined. It is shown that introduction of AgI into pores does not noticeably affect its structure.     

MAS NMR studies of nanoporous matrices filled with sodium nitrite

The sodium nitrite NaNO2 incorporated into MCM-41 molecular sieves with pore sizes of 20, 26, and 37 Å has been investigated by 23Na magic-angle spinning NMR spectroscopy. It has been demonstrated that the structure of the crystalline phase of the nitrite in a confined geometry is similar to the structure of bulk nitrite NaNO2. The direct proof of the diffuse melting of sodium nitrite in the pores has been obtained. The NMR signal of the molten sodium nitrite phase has been observed at temperatures close to the completion of the melting.