空腔流动的大涡模拟及气动噪声控制

大涡模拟(LES)和三维的Ffowcs Williams-Hawkings声学比拟方法相结合,研究空腔过流的一种噪声控制措施.空腔的底板/后墙使用多孔壁板,因此流体可以穿透空腔壁面,多孔效果使用Darcy压力-速度关系模拟.声源流场由LES计算,声辐射和远声场由声学比拟获得.结果表明,这种措施有效地减弱了空腔内的压力脉动和远场声辐射,低频脉动Rossiter模数对应的波动幅值被有效抑制,声源中偶极子占优项大幅度减小,从而抑制了声辐射.     

利用大型通用程序求解声学问题

本文介绍了利用有限元通用程序求解声学问题的声学——固体力学比拟法。该方法允许使用固体单元来模拟声介质。结合二维声空腔的模态分析和排气消声单元的传递损失计算说明了该方法的应用。给出了边界条件的处理方法及声粒子速度的计算公式。     

矢量气动声学的理论研究进展及应用

气动声学的声比拟理论以密度、声压等标量为波动算子变量,建立非齐次波动方程,描述流体运动及与边界作用诱发声音的辐射,但标量无法直接描述声能量的传播过程和途径.在流体力学研究中,标量用于描述当前当地的物质状态,而矢量用于描述质量和能量的传输.借鉴上述思想,开展了矢量气动声学的研究,概述矢量气动声学的理论研究进展及应用,主要包括:（1）以声粒子速度为变量,采用声比拟理论的思想直接从Navier-Stokes方程出发推导建立了气动声学的矢量波动方程及两种频域解;（2）综合利用声压和声粒子速度的积分解,直接求解声源周围的瞬时和有功声强矢量场,直观显示声能量的传播途径,应用于旋转声源辐射声能量的传播分析,揭示了亚音速旋转声源辐射声能量的3种传播模式:螺旋模式、声学黑洞模式和R-A模式;（3）采用球谐级数展开方法建立旋转点/紧凑声源辐射噪声的声压和声粒子速度的频域解析解,在此基础上推导了声功率谱的频域解析解,建立了识别旋转叶片声源在空间域和频域分布特征的方法;（4）综合利用矢量气动声学方法和等效源方法,显示声源和散射边界周围声强矢量场的分布特征和能量传播途径,直接揭示了阻抗边界主要的吸声位置以及直接计算得到阻抗边界的吸收声功率.      

弧形锯齿进口导流罩对轴流风扇性能的影响

本文应用LES/FW-H方法,研究了在导流罩入口采用弧形锯齿结构的半开式轴流风扇的气动声学性能。研究结果表明,采用弧形锯齿进口的周向非等宽导流罩可减小叶尖涡影响区域,降低叶尖涡强度。导流罩进口结构的变化对叶尖涡涡心轨迹有一定影响,弧形锯齿进口导流罩使得叶尖涡轨迹更远离轴心,随着弧形锯齿数目的增加,其叶尖涡轨迹越远离轴心。半开式轴流风扇的总噪声和导流罩的声辐射特性密切相关,采用弧形锯齿进口导流罩可降低风扇气动噪声,其中出口轴线方向可降低3 dB以上,且在一定范围内随着弧形锯齿数目的增加降噪程度越明显。     

基于转捩模型及声比拟方法的高精度圆柱分离涡/涡致噪声模拟

基于七阶加权紧致非线性格式(WCNS-E8T7),结合延迟分离涡模拟(DDES)和Ffowcs WilliamsHawkings声比拟方法,对亚临界雷诺数下单圆柱、圆柱-翼型的分离涡/涡致噪声问题进行了数值模拟.针对亚临界雷诺数下圆柱尾迹中的转捩问题,发展了基于γ-Reθ模型高精度转捩-延迟分离涡模拟(Tran-DDES)方法,并与传统基于全湍流剪切应力输运(SST)模型的高精度DDES方法进行了对比.单圆柱模拟结果表明:传统SST-DDES方法会造成平均流场的回流区增大,压差阻力偏小等问题;而添加转捩模型的Tran-DDES方法与实验符合得很好.圆柱尾迹中添加翼型后,翼型对圆柱附近流场产生影响,使SST-DDES方法造成的圆柱后回流区偏大的问题减弱,并与Tran-DDES模拟结果差异变小.但在脉动量预测以及脉动产生的噪声预测方面, Tran-DDES方法仍与实验符合得更好.     

微孔共振腔吸声机理的直接数值模拟研究

声衬是由大量的微孔共振腔按一定规则排列组成,由于微孔共振腔的小尺寸和流动的复杂性,采用实验和理论方法难以观测其内部及附近的复杂流动情况.本文采用计算气动声学方法对不同频率和声强声波入射下的二维微孔共振腔的吸声过程进行了直接数值模拟.结果表明: (1)腔口处粘性耗散和涡脱落现象是其吸声的书要形式;(2)在不同的频率和声强入射下,微孔共振腔的吸声过程表现出三种不同的模式,分别为无涡脱落、规则涡脱落和不规则涡脱落;(3)微孔共振腔的吸声性能在入射波为共振腔固有频率时最好.     

格子Boltzmann方法应用于气动声学研究

应用格子Boltzmann方法(LBM)对不同类型的气动声学问题进行数值研究.通过模拟一维平面声波和二维点源声波的传播,得到沿传播方向的声压脉动,其振荡幅值和衰减趋势与理论值相吻合.其次进行声波衍射和干涉现象的数值模拟.最后,模拟处于流场中运动声源辐射声场的多普勒效应.模拟结果说明LBM方法能较好地模拟低马赫数下的声学问题,包括声压脉动的传播,声波的波动特性以及流动与声波间的相互作用.     

贯流风扇气动声场数值模拟及分析

针对贯流风扇气动噪声传播特性,采用基于非结构网格的CE/SE算法对其气动流场进行数值模拟,并模拟了气动噪声的传播.湍流模拟采用大涡模型,搭接式滑移网格模型处理动静干涉.噪声传播采用完全欧拉方程作为控制方程,远场采用无反射边界条件.将使用该方法得到的远场噪声频谱与实验数据进行对比分析,结果表明与实验测量得到宽带频谱不同,采用大涡模拟湍流模型进行声源模拟时,会加强部分离散频率上的声级,从而产生误差.     

含空腔的功能梯度声学覆盖层水下吸声特性

针对传统的声学覆盖层吸声频带窄的问题,基于功能梯度材料的特点提出了一种含空腔结构的水下功能梯度声学覆盖层结构,引入梯度有限元法建立了功能梯度型声学覆盖层的水下声学计算模型,研究了功能梯度声学覆盖层结构的水下吸声特性。与传统的功能梯度结构声学建模方法相比,在保证计算精度和计算效率的基础上,文中所建立的功能梯度结构声学计算模型可适用于更复杂的功能梯度声学结构声学性能评估。研究结果表明,功能梯度声学覆盖层能够有效改善中高频段的吸声性能,获得较好的宽频吸声效果。此外,空腔形状采用锥型空腔结构或者组合型空腔结构可以有效地拓宽功能梯度声学覆盖层的吸声频带。      

基于主动声学超材料的圆柱声隐身斗篷设计研究

基于多层复合材料结构的二维声隐身斗篷设计思想, 利用主动隔膜声学空腔有效密度可以任意控制这一特性, 设计了主动声学超材料下的无限长圆柱声隐身斗篷. 给出了主动隔膜声学空腔单元的声电元件类比模拟电路图和具体的有效密度控制方法. 进行了主动声学超材料声隐身斗篷的结构建模, 并对平面入射波入射下此圆柱隐身斗篷周围声压分布场进行仿真计算. 结果表明, 平面波在一定频率范围内可以毫无阻碍地透过圆柱斗篷, 似乎不存在这种障碍物, 达到声隐身效果. 同时, 计算了主动声材料斗篷下总散射截面随频率变化曲线, 研究了此斗篷隐身效果随频率的变化特性. 本文从主动控制角度探讨实验实现隐身斗篷的技术问题, 有望给声隐身斗篷实验设计提供一条新的技术途径.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.