大气压甲烷针-板放电等离子体中粒子密度和反应路径的数值模拟

甲烷针-板放电与重油加氢耦合形成甲烷转化重油加氢,可实现重油高效加氢并增产高附加值低碳烯烃,有实践应用前景和科学研究意义.建立二维流体模型,对大气压甲烷针-板放电等离子体进行数值模拟,得到电场强度、电子温度和粒子密度的空间与轴向分布,总结反应产额并提炼生成各种带电和中性粒子的关键路径.模拟结果表明,CH_3~+和CH_4~+密度与电场强度和电子温度的轴向演化接近且密切相关;CH_5~+和C_2H_5~+密度沿轴向先增大后减小;CH_3与H密度的空间和轴向分布几乎相同;CH_2,C_2H_4与C_2H_5的粒子密度分布在靠近阴极的区域内明显不同而在正柱区内较为相像;电子与CH_4发生电子碰撞电离生成的CH_3~+和CH_4~+,CH_3~+和CH_4~+分别与CH_4发生分子碰撞解离生成C_2H_5~+和CH_5~+;电子与CH_4间的电子碰撞分解是生成CH_3,CH_2,CH和H的主导反应;CH_2与CH_4和电子与C_2H_4发生的反应分别是生成C_2H_4和C_2H_2的关键路径;电子与CH_4间的电子碰撞分解反应和CH_2与CH_4发生的反应的产额各占H_2总产额的52.15%和47.85%.     

潘宁源放电的全三维电磁粒子模拟/蒙特卡罗碰撞数值算法研究

深入研究潘宁放电的物理机制, 研制了全三维高品质算法粒子模拟软件(PIC), 设计并添加了相应物理情景的蒙特卡罗碰撞模块(MCC), 并对电子、氢分子离子(H₂⁺)、氢正离子(H⁺)、氢三正离子(H₃⁺)同时进行了跟踪, 成功研制了全三维电磁PIC/MCC数值算法. 结合国内研究较热的潘宁放电模型, 对该算法进行模拟验证. 模拟结果显示: 采用有效的滤波算法能抑制电磁数值噪声, 电子能量呈麦克斯韦分布, 由于电子的径向漂移和加速导致离子源顶端H₂⁺产量较大. 关键词： 潘宁离子源 高品质算法 粒子模拟/蒙特卡罗     

Superconductivity in Alkali-Doped C60

There ark three kinds of effective attractive interaction between C₆₀^2- and "nearly free" electron in A₃C₆₀: 1) the strong short-range attraction between the low energy unoccupied orbital of C₆₀^2- ions and the "nearly free" electrons; 2) the potential barrier due to large angular momentum of t_1u orbital; 3) the A⁺ crystal field forced "nearly free" electrons in C₆₀^2- neighborhood. All effective attraction coupling with the A⁺ optical modes and the vibration modes of C₆₀ mass center produces a strong electron-phonon interaction. It plays a principal role for A₃C₆₀ superconductivity. Based upon this mechanism critical temperature and other properties of superconductivity state can be explained by means of the BCS theory.     

��������Ƶ���Ƶ������Ϸŵ�������������ıȽ�

开发了氢气甚高频(60MHz)容性耦合放电的PIC/MC模型.在模型中考虑了带电粒子(e,H+,H2+,H3+)与H2的21种碰撞反应过程,模拟了氢气甚高频放电射频电场和电势分布以及电子和氢离子(H+,H2+,H3+)粒子密度和平均能量分布,并与频率为13.56MHz的放电结果进行了比较.结果表明,相对于频率13.56MHz的放电,氢气甚高频放电等离子体电势增高,导致两电极附近的电场增强;另外,两鞘层厚度变窄并且电子和H3+离子平均能量减小,其总密度却增加.H3+离子为氢气甚高频放电空间的主要离子,H2+离子密度比H3+离子小约2～3个数量级.     

Study of the electron damage of the MgO(100)-D2O system by ESD

An electron-stimulated desorption (ESD) study of electron damage of a D₂O layer adsorbed on the MgO(100) surface at room temperature is presented. After exposing the surface to D₂O, the surface spectrum shows the main ESD component to be D⁺ ions, with lower intensity signals corresponding to O⁺ and OD⁺ ions. When the surface is simultaneously exposed to heavy water and electron bombardment, there is a rapid initial increase of the D⁺ intensity accompanied by a decrease of the intensity of the O⁺ ions. Electron damage of the surface after exposing to D₂O produces a significant decrease of the D⁺ intensity, while the O⁺ and OD⁺ intensities decrease more slowly. Heavy water adsorption does not change the form of the ion kinetic energy distribution of the O⁺ ions with electron dose, except for a decrease in intensity. Electron damage increases the intensity of the ion kinetic energy distribution of D⁺ again without changing its shape. These experiments show that heavy water adsorption under electron bombardment does not induce any chemistry of the adsorbed species, but enhances the fragmentation rate of the OD species which, in turn, increases the yield of D⁺ ions. Values of total desorption cross-sections for the three ions species are reported.     

多相氧载体CoO-MgO和氧分子作用的ESR研究

用ESK研究多相氧载体CoO-MgO表面上氧的吸附作用,发现在77-150K温度范围内表面Co²⁺离子和O₂的结合是可逆的,吸附产生Co³⁺-O₂^-自由基加合物有超精细结构的ESR谱;当温度增加,吸附态O₂^-自由基发生转移并稳定在Mg²⁺离子上形成Mg²⁺-O₂^-自由基,文中着重讨论Co³⁺-O₂^-自由基的电子结构和成键本质,认为自由基是通过自旋成对的方式形成的,由于σ-л键作用引起的自旋极化以及由于电子离域作用而引起的偶极作用与ESR制的超精细结构线产生有关。     

Electron localization of linear symmetric molecular ion H_3~(2+)

Electron localization in the dissociation of the symmetric linear molecular ion H_3~(2+) is investigated. The numerical simulation shows that the electron localization distribution is dependent on the central frequency and peak electric field amplitude of the external ultrashort ultraviolet laser pulse. When the electrons of the ground state are excited onto the 2pσ~2Σ_u~+ by a one-photon process, most electrons of the dissociation states are localized at the protons on both sides symmetrically. Almost no electron is stabilized at the middle proton due to the odd symmetry of the wave function. With the increase of the frequency of the external ultraviolet laser pulse, the electron localization ratio of the middle proton increases, for more electrons of the ground state are excited onto the higher 3pσ~2Σ_u~+ ustate. 50.9% electrons of all the dissociation events can be captured by the middle Coulomb potential well through optimizing the central frequency and peak electric field amplitude of the ultraviolet laser pulse. Besides, a direct current(DC) electric field can be utilized to control the electron motions of the dissociation states after the excitation of an ultraviolet laser pulse, and 68.8% electrons of the dissociation states can be controlled into the middle proton.     

Anharmonic V–V pumping and asymmetric electron-elementary excitation interaction in emission and absorption of O2(Δg) in the crystalline phases of oxygen

Three luminescence bands in the yellow and red spectral region, which are related to the ¹Δ_g¹Δ_g→³Σ_g^{− 3}Σ_g⁻ double electronic transition of O₂, have been investigated in the , β, and γ phase of solid oxygen. The temperature dependence of the intensity of the yellow band is strongly influenced by emission from higher vibrational levels of O₂(¹Δ_g), which are populated by anharmonic V–V pumping. The broken mirror symmetry of the luminescence and absorption bands in the phase of solid O₂ points to an interaction between the electrons and the elementary excitations of the crystal, which is different in the ground and excited electronic states, e.g., a quadratic electron–phonon interaction.     

Work function changes and surface chemistry of oxygen, hydrogen, and carbon on indium tin oxide

The surface chemistry of indium tin oxide (ITO) has been investigated with Auger electron spectroscopy (AES) and high resolution electron energy loss spectroscopy (HREELS). A vibrating Kelvin probe (KP) with a graphite reference was used to monitor the absolute work function (Φ) of ITO as a function of chemical modification. The ITO was exposed in situ to molecular hydrogen (H₂), hot-filament-activated oxygen (O₂^*), and hot-filament-activated deuterium (D₂^*). The initial Φ of ITO was determined to be 5.2 eV, and surface chemical changes had strong effects on this value, as seen by KP. Exposure of clean ITO to O₂^* increased Φ to 5.6 eV, but the increase was short-lived. The changes in Φ over time were correlated with the uptake of carbon impurities in ultra high vacuum (UHV), as monitored by AES.

The HREELS of ITO revealed significant hydrocarbon impurities. Chemical reduction of ITO produced a metallic surface and dehydrogenated the adsorbed hydrocarbons. Both re-oxidation of metallic ITO and oxidation of clean ITO temporarily removed adventitious carbon from the surface, but oxidized ITO adsorbed an even larger quantity of carbon over time.     

Intrinsic luminescence centers in γ- and θ-alumina nanoparticles

In this study, we investigate the photoluminescence(PL) properties of γ and θ-alumina nanoparticles synthesized by the chemical wet method followed by annealing. The obtained experimental results indicate the presence of some favorable near ultraviolet(NUV)-orange luminescent centers for usage in various luminescence applications, such as oxygen vacancies(F, F~+_2, F~(2+)_2, and F_2centers), OH related defects, cation interstitial centers, and some new luminescence bands attributed to trapped-hole centers or donor–acceptor centers. The energy states of each defect are discussed in detail. The defects mentioned could alter the electronic structure by producing some energy states in the band gap that result in the optical absorption in the middle ultraviolet(MUV) region. Spectra show that photoionazation of F and F_2 centers plays a crucial role in providing either free electrons for the conduction band, or the photoconversions of aggregated oxygen vacancies into each other, or mobile electrons for electrons-holes recombination process by the Shockley–Read–Hall(SRH)mechanism.     

闪烁晶体的发光研究进展

概述了近年来闪烁体发光研究的进展,主要介绍用于未来高能物理实验的新型闪烁体发光机理研究,选取我们在研BaF₂,BaF₂:RE,CeF₃以及PbWO₄中的一些新进展。重点谈及三点:(1)在BaF₂的“价带^→芯带”跃迁发光研究基础上进行稀土(Gd³⁺-Eu³⁺)掺杂时观察到的量子剪裁以及对多光子发光的新思考;(2)CeF₃晶体发光的级联能量传递中,Ce³⁺(290nm发射带)与缺陷发光中心(340nm发射带)间能量传递及其传递效率的温度依赖;(3)PbWO₄晶体的发光中心研究中,提出以“WO₄^-2+O_i”绿光中心替代“WO³+F”中心观点的依据。同时也简介了医用闪烁体的最新进展。     

The adsorption of oxygen on Pd1/W(110)

The behavior of oxygen on Pd₁/W(110) has been investigated from 25 to 200 K by thermal desorption, UPS, XPS, and work function measurements. At 25 K only dioxygen species are present. A weakly bound O₂layer, containing O₂/Pd = 0.31 or 4.4 × 10¹⁴ O₂ molecules/cm² is desorbed at 35 K, leaving a coverage of O₂/Pd = 0.35 or 5 × 10¹⁴ O₂ molecules/cm². Heating to 200 K results in desorption of molecular O₂ as well as conversion to O, with O/Pd = 0.3. The molecular states, except the very weakly bound one, have high dipole moments with electron transfer to O₂, and thus correspond to Superoxide and peroxide species. These have UPS spectra quite different from physisorbed O₂. At 90 K adsorption is still mostly molecular with a sticking coefficient s near unity. At 200 K, adsorption is atomic with an initial s₀ = 0.8. This must be contrasted with Cu₁/W(110) where s₀ is unity even at 300 K. The difference can be explained by the much better size match of Pd and W, than Cu and W which makes it easier for Cu to take up momentum of impinging O₂ molecules.

The behavior of oxygen on Pd₁/W(110) is very similar to that on bulk Pd(111), suggesting that for oxygen the former surface resembles bulk Pd. This is not so for CO adsorption which is much weaker on Pd₁/W(110) than on bulk Pd. The reasons for this difference are not presently understood.     

Surface enhancement of molecular ion H_2~+ yield in a 2.45-GHz electron–cyclotron resonance ion source

High current hydrogen molecular ion beam is obtained with a specially designed stainless steel liner permanent magnet2.45-GHz electron–cyclotron resonance(ECR) ion source(PMECR II) at Peking University(PKU). To further understand the physics of the hydrogen generation process inside a plasma chamber, theoretical and experimental investigations on the liner material of the plasma chamber in different running conditions are carried out. Several kinds of materials, stainless steel(SS), tantalum(Ta), quartz, and aluminum(Al) are selected in our study. Experimental results show that stainless steel and tantalum are much better than others in H~+_2 generation. During the experiment, an increasing trend in H~+_2 fraction is observed with stainless steel liner after O_2 discharge inside the ion source. Surface analyses show that the roughness change on the surface after O_2 discharge may be responsible for this phenomenon. After these studies, the pure current of H~+_2 ions can reach 42.3 mA with a fraction of 52.9%. More details are presented in this paper.     

Shell-model calculations with Woods-Saxon wave functions in O and Ca

Two-particle states of ¹⁸O and ⁴²Ca are calculated within the shell model. The nuclear cores are represented by Woods-Saxon potentials, and for the residual interaction, central forces of Yukawa and Gaussian types are used. The wave functions for the low-lying states except for the O₂⁺ and 2₂⁺ states in ⁴²Ca are obtained, and the calculated energy spectra are in good agreement with experiments. Also E2 transitions are calculated and compared with experimental results.     

激光诱导氮气等离子体时间分辨光谱研究及温度和电子密度测量

激光诱导击穿光谱(LIBS)作为一种重要的分析手段被广泛应用于材料分析、环境监测等领域.特别是随着大气污染问题的日趋严重,基于LIBS的大气污染在线监测分析技术快速发展,氮气等离子体特性的时间演化规律对研究激光诱导大气等离子体动力学和发展大气污染监测的LIBS技术具有重要意义.而温度和电子数密度作为表征等离子体状态最重要的参数,直接影响着等离子体形成、膨胀和退化中的动力学过程以及等离子体中的能量传输效率.本文利用等离子体时间分辨光谱,研究了连续背景辐射、分子谱线强度及信背比(分子谱线与连续背景辐射的比值)在等离子体演化过程中的变化规律,结果显示连续背景辐射寿命在700 ns左右,N_2~+(B~2Σ_u~+-X~2Σ_g~+,v:0-0)跃迁谱线强度在12—15μs范围内达到最大值,信背比随时间呈现上升、稳定的趋势,因此利用N+2分子离子第一负带系(B~2Σ_u~+-X~2Σ_g~+)研究等离子体温度的观测窗口应选择在10—25μs之间;基于双原子光谱理论,通过拟合实测光谱和仿真光谱研究了大气压下激光诱导氮气等离子体温度随时间的演化趋势,由于辐射损耗远小于碰撞作用,在10—28μs内等离子体温度从约10000 K按指数衰减到约6000 K;在准确测定仪器展宽线型的基础上,利用Nelder-Mead单纯形算法,研究了N原子746.831 nm谱线的Stark展宽和位移随时间的演化趋势,计算了等离子体中电子数密度随时间在10~(17)—10~(16)cm~(-3)量级间衰减,通过分析发现造成等离子体中电子数衰减的主要机理是三体碰撞复合.     

Eu2+在磷酸镧中的发光及Ce3+→Eu2+的能量传递

采用高温固相反应合成了LaPO₄:Eu²⁺和LaPO₄:Ce³⁺,Eu²⁺样品,报道了Eu²⁺在LaPO₄中的发光性质和Ce³⁺→Eu²⁺的能量传递现象。文中探讨了Ce³⁺→Eu²⁺的能量传递机理,根据Dexter电多极相互作用的理论证明其为偶极子偶极子相互作用的共振能量传递。     

Electron localization of H_2~+ in a dc electric field

A dc electric field is utilized to steer the electron motion after the molecular ion H_2~+ is excited by an ultrashort ultraviolet laser pulse. The numerical simulation shows that the electron localization distribution and the dissociation control ratio are dependent on the polarization direction and amplitude of the dc electric field. Most electrons of the dissociation state move opposite to the dc electric field and stabilize at the dressed-up potential well, for the dressed-down well is occupied by the electrons of the 1 sσ_g state.     

Adsorption and angle-resolved electron-stimulated desorption of CCl4 on Ru(0001)

The adsorption and electron-stimulated desorption of CCl₄ on Ru(0001) have been studied at 100 K using a variety of surface analytical techniques, including thermal desorption spectroscopy, Auger electron spectroscopy, low-energy ion scattering, and mass and angle-resolved electron-stimulated desorption (ESDIAD). CC1₄ is found to dissociate partially for fractional monolayer coverages, and to adsorb molecularly above a coverage of 13%. Upon electron bombardment, Cl⁺ ions are found to desorb with their angular distribution directed along the surface normal; this implies that CC1₄ orients with one C-C1 bond normal to the surface. The total yield of Cl⁺ increases linearly with increasing molecular CC1₄ coverage up to one monolayer, which implies that Cl⁺ stems mainly from molecular CCl₄ and that interadsorbate quenching is not significantly affecting the desorption yield. Beyond a coverage of 1 ML, the Cl⁺ yield continues to increase, and starts leveling off after 2 ML. We estimate the yield from a thick layer of CCl⁴ to be of the order of 3 × 10⁻⁸ ions/electron. The angular distribution of the desorbing Cl⁺ ions widens with increasing CCl₄ exposure. Besides Cl⁺, higher mass fragments of CCl₄, such as CCl⁺, CCl₂⁺ and CCl₃⁺ are also found to desorb from multilayers upon electron bombardment.     

Ionic oxygen species formed in the presence of lithium, potassium and cesium

Various thick oxidized Li, K and Cs layers have been analysed. The O²⁻, O₂²⁻ and O₂⁻ ions have been characterized through the multiplet structures of their valence-band spectra. Furthermore, the energy separations between the O 1s core levels and the O 2p valence levels were seen to take some given values for each oxygen species. This provides a new way to unambiguously identify these species. In addition, the above energy separations compare rather well to the free ion values, thus allowing discussion on the representation of the oxygen ions which are formed in the presence of alkali metals in terms of a point-charge model.