Al2O3绝缘层的AlGaN/GaN MOSHEMT器件研究

在研制AlGaN/GaN HEMT器件的基础上,采用ALD法制备了Al₂O₃ AlGaN/GaN MOSHEMT器件.通过X射线光电子能谱测试表明在AlGaN/GaN异质结材料上成功淀积了Al₂O₃薄膜.根据对HEMT和MOSHEMT器件肖特基电容、器件输出以及转移特性的测试进行分析发现：所制备的Al₂O₃薄膜与AlGaN外延层间界面态密度较小,因而MOSHEMT器件呈现出较 关键词： 2O₃')" href="#">Al₂O₃ ALD GaN MOSHEMT     

Performance of La2O3/InAlN/GaN metal—oxide—semiconductor high electron mobility transistors

We report on the performance of La2O3/InAlN/GaN metal-oxide-semiconductor high electron mobility transistors(MOSHEMTs) and InAlN/GaN high electron mobility transistors(HEMTs).The MOSHEMT presents a maximum drain current of 961 mA/mm at Vgs = 4 V and a maximum transconductance of 130 mS/mm compared with 710 mA/mm at Vgs = 1 V and 131 mS/mm for the HEMT device,while the gate leakage current in the reverse direction could be reduced by four orders of magnitude.Compared with the HEMT device of a similar geometry,MOSHEMT presents a large gate voltage swing and negligible current collapse.     

A study on Al2O3 passivation in GaN MOS-HEMT by pulsed stress

This paper studies systematically the drain current collapse in AlGaN/GaN metal-oxide-semiconductor high electron mobility transistors （MOS-HEMTs） by applying pulsed stress to the device. Low-temperature layer of Al2O3 ultrathin film used as both gate dielectric and surface passivation layer was deposited by atomic layer deposition （ALD）. For HEMT, gate turn-on pulses induced large current collapse. However, for MOS-HEMT, no significant current collapse was found in the gate turn-on pulsing mode with different pulse widths, indicating the good passivation effect of ALD Al2O3. A small increase in Id in the drain pulsing mode is due to the relieving of self-heating effect. The comparison of synchronously dynamic pulsed Id - Vds characteristics of HEMT and MOS-HEMT further demonstrated the good passivation effect of ALD Al2O3.     

The electrical characteristics of a 4H-silicon carbide metal-insulator-semiconductor structure with Al2O3 as the gate dielectric

A 4H-silicon carbide metal-insulator-semiconductor structure with ultra-thin Al₂O₃ as the gate dielectric, deposited by atomic layer deposition on the epitaxial layer of a 4H-SiC (0001) 8⁰N-/N+ substrate, has been fabricated. The experimental results indicate that the prepared ultra-thin Al₂O₃ gate dielectric exhibits good physical and electrical characteristics, including a high breakdown electrical field of 25 MV/cm, excellent interface properties (1×10¹⁴ cm^-2) and low gate-leakage current (I_G = 1 × 10^-3 A/cm^-2@E_ox = 8 MV/cm). Analysis of the current conduction mechanism on the deposited Al₂O₃ gate dielectric was also systematically performed. The confirmed conduction mechanisms consisted of Fowler-Nordheim (FN) tunneling, the Frenkel-Poole mechanism, direct tunneling and Schottky emission, and the dominant current conduction mechanism depends on the applied electrical field. When the gate leakage current mechanism is dominated by FN tunneling, the barrier height of SiC/Al₂O₃ is 1.4 eV, which can meet the requirements of silicon carbide metal-insulator-semiconductor transistor devices.     

Ni/Au Schottky gate oxidation and BCB passivation for high-breakdown-voltage AlGaN/GaN HEMT

A new AlGaN/GaN high electron mobility transistor (HEMT) employing Ni/Au Schottky gate oxidation and benzocyclobutene (BCB) passivation is fabricated in order to increase a breakdown voltage and forward drain current. The Ni/Au Schottky gate metal with a thickness of 50/300 nm is oxidized under oxygen ambient at 500 C and the highly resistive NiO is formed at the gate edge. The leakage current of AlGaN/GaN HEMTs is decreased from 4.94 μA to 3.34 nA due to the formation of NiO. The BCB, which has a low dielectric constant, successfully passivates AlGaN/GaN HEMTs by suppressing electron injection into surface states. The BCB passivation layer has a low capacitance, so BCB passivation increases the switching speed of AlGaN/GaN HEMTs compared with silicon nitride passivation, which has a high dielectric constant. The forward drain current of a BCB-passivated device is 199 mA /mm, while that of an unpassivated device is 172 mA /mm due to the increase in two-dimensional electron gas (2DEG) charge.     

The improvement of Al2O3/AlGaN/GaN MISHEMT performance by N2 plasma pretreatment

This paper discusses the effect of N 2 plasma treatment before dielectric deposition on the electrical performance of a Al2O3 /AlGaN/GaN metal-insulator-semiconductor high electron mobility transistor(MISHEMT),with Al2O3 deposited by atomic layer deposition.The results indicated that the gate leakage was decreased two orders of magnitude after the Al2O3 /AlGaN interface was pretreated by N 2 plasma.Furthermore,effects of N 2 plasma pretreatment on the electrical properties of the AlGaN/Al2O3 interface were investigated by x-ray photoelectron spectroscopy measurements and the interface quality between Al2O3 and AlGaN film was improved.     

Characteristics of sandwich-structured Al2O3/HfO2/Al2O3 gate dielectric films on ultra-thin silicon-on-insulator substrates

Sandwich-structure Al₂O₃/HfO₂/Al₂O₃ gate dielectric films were grown on ultra-thin silicon-on-insulator (SOI) substrates by vacuum electron beam evaporation (EB-PVD) method. AFM and TEM observations showed that the films remained amorphous even after post-annealing treatment at 950 °C with smooth surface and clean silicon interface. EDX- and XPS-analysis results revealed no silicate or silicide at the silicon interface. The equivalent oxide thickness was 3 nm and the dielectric constant was around 7.2, as determined by electrical measurements. A fixed charge density of 3 × 10¹⁰ cm⁻² and a leakage current of 5 × 10⁻⁷A/cm² at 2 V gate bias were achieved for Au/gate stack /Si/SiO₂/Si/Au MIS capacitors. Post-annealing treatment was found to effectively reduce trap density, but increase in annealing temperature did not made any significant difference in the electrical performance.     

Sodium beta-alumina thin films as gate dielectrics for A1GaN/GaN metal-insulator-semiconductor high-electron-mobility transistors

<正>Sodium beta-alumina（SBA） is deposited on AlGaN/GaN by using a co-deposition process with sodium and Al₂O₃ as the precursors.The X-ray diffraction（XRD） spectrum reveals that the deposited thin film is amorphous.The binding energy and composition of the deposited thin film,obtained from the X-ray photoelectron spectroscopy（XPS） measurement,are consistent with those of SBA.The dielectric constant of the SBA thin film is about 50.Each of the capacitance-voltage characteristics obtained at five different frequencies shows a high-quality interface between SBA and AlGaN.The interface trap density of metal-insulator-semiconductor high-electron-mobility transistor（MISHEMT） is measured to be（3.5～9.5）×10¹⁰ cm^-2·eV^-1 by the conductance method.The fixed charge density of SBA dielectric is on the order of 2.7×10¹² cm^-2.Compared with the AlGaN/GaN metal-semiconductor heterostructure high-electronmobility transistor（MESHEMT）,the AlGaN/GaN MISHEMT usually has a threshold voltage that shifts negatively. However,the threshold voltage of the AlGaN/GaN MISHEMT using SBA as the gate dielectric shifts positively from—5.5 V to—3.5 V.From XPS results,the surface valence-band maximum（VBM-E_F） of AlGaN is found to decrease from 2.56 eV to 2.25 eV after the SBA thin film deposition.The possible reasons why the threshold voltage of AlGaN/GaN MISHEMT with the SBA gate dielectric shifts positively are the influence of SBA on surface valence-band maximum （VBM-E_F）,the reduction of interface traps and the effects of sodium ions,and/or the fixed charges in SBA on the two-dimensional electron gas（2DEG）.     

Investigation of 4H—SiC metal—insulation—semiconductor structure with Al2O3/SiO2 stacked dielectric

Atomic layer deposited (ALD) Al₂O₃/dry-oxidized ultrathin SiO₂ films as high-k gate dielectric grown on the 8° off-axis 4H-SiC (0001) epitaxial wafers are investigated in this paper. The metal-insulation-semiconductor (MIS) capacitors, respectively with different gate dielectric stacks (Al₂O₃/SiO₂, Al₂O₃, and SiO₂) are fabricated and compared with each other. The I-V measurements show that the Al₂O₃/SiO₂ stack has a high breakdown field ( ≥ 12 MV/cm) comparable to SiO₂, and a relatively low gate leakage current of 1× 10^-7 A/cm² at electric field of 4 MV/cm comparable to Al₂O₃. The 1-MHz high frequency C-V measurements exhibit that the Al₂O₃/SiO₂ stack has a smaller positive flat-band voltage shift and hysteresis voltage, indicating less effective charge and slow-trap density near the interface.     

Room temperature fabrication Oxide TFT with Y2O3 as a gate oxide and Mo contact

In this investigation, an operating voltage as low as 5 V has been achieved for Oxide TFT with Y₂O₃ as a gate oxide and a-IGZO as an active layer. The OTFT has been fabricated at room temperature using RF sputter. The mobility and threshold voltages are 11.3 cm²/V s and 3.4 V for the device with W/L = 0.8, respectively. The annealing at 400 °C in N₂ containing 5% H₂ ambient has been utilized to improve the electrical performance of TFT. The on-off current which is determined by gate dielectric has been observed to be 10⁴. It has also been observed that the dielectric properties of gate oxide deteriorate on annealing. The dielectric constant of Y₂O₃ is observed in the range between 5.1 and 5.4 measured on various devices.     

Al2O3绝缘栅AlGaN/GaN MOS-HEMT器件温度特性研究

采用原子层淀积(ALD)实现了10nm Al₂O₃为栅介质的高性能AlGaN/GaN金属氧化物半导体高电子迁移率晶体管(MOS-HEMT). 通过对MOS-HEMT器件和传统MES-HEMT器件室温特性的对比,验证了新型MOS-HEMT器件饱和电流和泄漏电流的优势. 通过分析MOS-HEMT器件在30—180℃之间特性的变化规律,与国内报道的传统MES-HEMT器件随温度退化程度对比,得出了器件饱和电流和跨导的退化主要是由于输运特性退化造成的,证明栅介质减小了引 关键词： 原子层淀积 AlGaN/GaN MOS-HEMT器件 温度特性     

Characterization of Al2O3 /GaN/AlGaN/GaN metalinsulator-semiconductor high electron mobility transistors with different gate recess depths

In this paper,in order to solve the interface-trap issue and enhance the transconductance induced by high-k dielectric in metal-insulator-semiconductor (MIS) high electron mobility transistors (HEMTs),we demonstrate better performances of recessed-gate Al 2 O 3 MIS-HEMTs which are fabricated by Fluorine-based Si 3 N 4 etching and chlorinebased AlGaN etching with three etching times (15 s,17 s and 19 s).The gate leakage current of MIS-HEMT is about three orders of magnitude lower than that of AlGaN/GaN HEMT.Through the recessed-gate etching,the transconductance increases effectively.When the recessed-gate depth is 1.02 nm,the best interface performance with τ it =(0.20-1.59) μs and D it =(0.55-1.08)×10 12 cm 2 ·eV 1 can be obtained.After chlorine-based etching,the interface trap density reduces considerably without generating any new type of trap.The accumulated chlorine ions and the N vacancies in the AlGaN surface caused by the plasma etching can degrade the breakdown and the high frequency performances of devices.By comparing the characteristics of recessed-gate MIS-HEMTs with different etching times,it is found that a low power chlorine-based plasma etching for a short time (15 s in this paper) can enhance the performances of MIS-HEMTs effectively.     

Al2O3介质层厚度对AlGaN/GaN金属氧化物半导体-高电子迁移率晶体管性能的影响

在蓝宝石衬底上采用原子层淀积法制作了三种不同Al₂O₃介质层厚度的绝缘栅高电子迁移率晶体管.通过对三种器件的栅电容、栅泄漏电流、输出和转移特性的测试表明：随着Al₂O₃介质层厚度的增加,器件的栅控能力逐渐减弱,但是其栅泄漏电流明显降低,击穿电压相应提高.通过分析认为薄的绝缘层能够提供大的栅电容,因此其阈值电压较小,但是绝缘性能较差,并不能很好地抑制栅电流的泄漏;其次随着介质厚度的增加,可以对栅极施加更高的正偏压,因此获 关键词： 2O₃')" href="#">Al₂O₃ 金属氧化物半导体-高电子迁移率晶体管 介质层厚度 钝化     

The electrical properties of dielectric stacks of SiO2 and Al2O3 prepared by atomic layer deposition method

We produced dielectric stacks composed of ALD SiO₂ and ALD Al₂O₃, such as SiO₂/Al₂O₃, Al₂O₃/SiO₂, and SiO₂/Al₂O₃/SiO₂, and measured the leakage currents through the stacks in comparison with those of the single oxide layers. SiO₂/Al₂O₃ shows lowest leakage current for negative bias region below 6.4 V, and Al₂O₃/SiO₂ showed highest current under negative biases below 4.5 V. Two distinct electron conduction regimes are observed for Al₂O₃ and SiO₂/Al₂O₃. Poole-Frenkel emission is dominant at the high-voltage regime for both dielectrics, whereas the direct tunneling through the dielectric is dominant at the low-voltage regime. The calculated transition voltage between two regimes for SiO₂ (6.5 nm)/Al₂O₃ (12.6 nm) is −6.4 V, which agrees well with the experimental observation (−6.1 V). For the same EOT of entire dielectric stack, the transition voltage between two regimes decreases with thinner SiO₂ layer.     

Improved performance of InGaZnO thin-film transistors with Ta2O5/Al2O3 stack deposited using pulsed laser deposition

Ta₂O₅/Al₂O₃ stacked thin film was fabricated as the gate dielectric for low-voltage-driven amorphous indium–gallium–zinc-oxide (IGZO) thin film transistors (TFTs). The Ta₂O₅/Al₂O₃ stacked thin film exhibits a combination of the advantages of Al₂O₃ and Ta₂O₅. The IGZO TFT with Ta₂O₅/Al₂O₃ stack exhibits good performance with large saturation mobility of 26.66 cm² V⁻¹ s⁻¹, high on/off current ratio of 8 × 10⁷, and an ultra-small subthreshold swing (SS) of 78 mV/decade. Such small SS value is even comparable with that of submicrometer single-crystalline Si MOSFET.     

The effect of barrier strain on the reliability of Inx Al1–xN/AlN/GaN heterostructure field‐effect transistors

We report on the reliability of In_x Al_1–xN/AlN/GaN‐based heterostructure field‐effect transistors (HFETs) fabricated on five different wafers with varying indium compositions (0.12 ≤ x ≤ 0.20) encompassing the tensile/compressive strain fields. All of the tested devices underwent high field on‐state stress at 20 V DC drain bias and zero gate bias for five hours. We monitored the drain current and low‐frequency noise (LFN) a priori and a posteriori the stress treatment to quantify device degradation. HFETs suffering tensile strain showed remarkably large degradation which manifested itself with up to 25 dB increase in noise power and up to 72% loss of drain current after stress. On the other hand, devices fabricated on compressively strained structures remained intact after stress, but they had about 30 dB higher pre‐stress noise‐power levels and about 50% lower drain‐current densities to begin with. The results show that the nearly lattice‐matched In_0.17Al_0.83N barrier exhibited very low degradation along with current density remaining high compared with the devices having barriers with lower or higher indium content. Our results suggest that the nearly‐lattice‐matched InAlN can be a good candidate for devices due to its relatively better reliability while maintaining a high current density. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Performance of La₂O₃/InAlN/GaN metal-oxide-semiconductor high electron mobility transistors

We report on the performance of La2O3/InAlN/GaN metal-oxide-semiconductor high electron mobility transistors(MOSHEMTs) and InAlN/GaN high electron mobility transistors(HEMTs).The MOSHEMT presents a maximum drain current of 961 mA/mm at Vgs = 4 V and a maximum transconductance of 130 mS/mm compared with 710 mA/mm at Vgs = 1 V and 131 mS/mm for the HEMT device,while the gate leakage current in the reverse direction could be reduced by four orders of magnitude.Compared with the HEMT device of a similar geometry,MOSHEMT presents a large gate voltage swing and negligible current collapse.     

AlGaN/GaN HEMTs grown on silicon (001) substrates by molecular beam epitaxy

We report the realization of an AlGaN/GaN HEMT on silicon (001) substrate with noticeably better transport and electrical characteristics than previously reported. The heterostructure has been grown by molecular beam epitaxy. The 2D electron gas formed at the AlGaN/GaN interface exhibits a sheet carrier density of 8×10¹² cm⁻² and a Hall mobility of 1800 cm²/V s at room temperature. High electron mobility transistors with a gate length of 4 μm have been processed and DC characteristics have been achieved. A maximum drain current of more than 500 mA/mm and a transconductance g_m of 120 mS/mm have been obtained. These results are promising and open the way for making efficient AlGaN/GaN HEMT devices on Si(001).     

Phase transformation behavior and dielectric characteristics of BaTi1−x(Al1/2Nb1/2)xO3 (0.01≤x≤0.40) ceramics

Microstructure, phase transformation behavior and dielectric properties of BaTi_1−x(Al_1/2Nb_1/2)_xO₃ (0.01≤x≤0.40) ceramics were investigated. A high level of (Al_1/2Nb_1/2)⁴⁺ substitution for Ti⁴⁺ ions was not conducive to the stability of the perovskite structure and resulted in the formation of BaAl₂O₄. As x was increased, lattice constants and unit cell volume decreased, reached a minimum at x=0.10 and then increased. The BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics at room temperature experienced a transformation from ferroelectric to paraelectric phase with increasing (Al_1/2Nb_1/2)⁴⁺ concentration. Meanwhile, permittivity of the BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics was markedly reduced, while Q value was slightly increased. Frequency dispersion of dielectric peak was obviously increased as x was increased from 0.01 to 0.10. It is of great interest that a dielectric abnormity represented by a broad dielectric peak at 200-400 K was observed for the composition with x=0.40.     

High vertical breakdown strength in with low specific on‐resistance AlGaN/AlN/GaN HEMTs on silicon

Off‐state and vertical breakdown characteristics of AlGaN/AlN/GaN high‐electron‐mobility transistors (HEMTs) on high‐resistivity (HR)‐Si substrate were investigated and analysed. Three‐terminal off‐state breakdown (BV_gd) was measured as a function of gate–drain spacing (L_gd). The saturation of BV_gd with L_gd is because of increased gate leakage current. HEMTs with L_gd = 6 µm exhibited a specific on‐resistance R_DS[ON] of 0.45 mΩ cm². The figure of merit (FOM = BV_gd²/R_DS[ON]) is as high as 2.0 × 10⁸ V² Ω^–1 cm^–2, the highest among the reported values for GaN HEMTs on Si substrate. A vertical breakdown of ～1000 V was observed on 1.2 µm thick buffer GaN/AlN grown on Si substrate. The occurrence of high breakdown voltage is due to the high quality of GaN/AlN buffer layers on Si substrate with reduced threading dislocations which has been confirmed by transmission electron microscopy (TEM). This indicates that the AlGaN/AlN/GaN HEMT with 1.2 µm thick GaN/AlN buffer on Si substrate is promising candidate for high‐power and high‐speed switching device applications. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)