一种监测钢筋腐蚀的光纤光栅传感器的研究

钢筋腐蚀是导致钢筋混凝土结构耐久性劣化的最重要因素之一。钢筋腐蚀将导致钢筋体积大大增加,混凝土保护层开裂、剥落,结构承载力下降,甚至倒塌。基于光纤布拉格光栅应变传感器的原理,根据钢筋腐蚀体积膨胀,提出了一种新的钢筋腐蚀光纤光栅传感器及温度补偿方法。传感器构造是在两根紧靠的钢筋中心附近粘贴光纤光栅,由于钢筋腐蚀体积膨胀,钢筋直径增加将转变成布拉格光纤光栅的应变,从而实现对钢筋腐蚀程度及速率的监测。传感器的监测原理是设置一个钢筋腐蚀光纤光栅传感器来监测由于钢筋腐蚀和温度变化引起的光栅应变,同时单独设置一个不锈钢光纤光栅传感器来测量温度引起的光栅应变。这两个光纤光栅传感器的应变监测,可分离出钢筋由于腐蚀所引起的体积变化。在混凝土结构中埋入封装的传感器,通过监测光纤光栅波长的漂移可以直接测量钢筋腐蚀程度,而且不受腐蚀因素的影响,可用于混凝土结构中钢筋腐蚀的早期监测。最后通过实验标定了钢筋腐蚀率与光栅波长位移的关系。     

基于光纤布拉格光栅传感器的光纤光栅智能夹层试验研究

传感元件与复合材料的一体化是智能结构研究的最终目标之一。设计一种具有自诊断功能的标准化、模块化光纤智能夹层系统,正是实现这种一体化最有潜力的技术途径。采用聚酰亚胺薄膜制作了基于光纤布拉格光栅（FBG）传感器的光纤光栅智能夹层,对智能夹层中光纤布拉格光栅传感器的应变、温度特性进行了标定试验,并建立了基于光纤布拉格光栅传感器光纤光栅智能夹层的应变、温度测量模型。试验表明,智能夹层内布拉格光栅波长偏移与应变、温度之间具有良好的线性关系。不过在温度测量时,必须考虑被埋人结构的热膨胀效应。利用光纤光栅智能夹层内光纤布拉格光栅传感器网络和先进信息处理技术,可以建立结构损伤主动、在线和实时监测系统。     

可分离温度影响的FBG应变测量方法

光纤布拉格光栅在通信和传感领域具有广泛的应用。利用光纤布拉格光栅中心波长的偏移，可以测量温度和应变等多种物理量，但必须解决光栅对温度和应变的交叉敏感问题。该文简要分析了光纤光栅作为传感器的基本原理及其优点，设计了利用参考光栅法分离温度影响以及利用掺铒光纤的自发发射放大特性分离温度影响的2种应变测量方法。最后，介绍了一种利用倾斜光纤光栅的主模和边模对布拉格光栅中心波长的偏移进行解调的方法，该方法成功地分离了温度对应变测量的影响。     

动态激励下的FBG应变传感器原位校准方法

针对光纤光栅应变传感器测量桥梁结构动态应变值的准确性问题,提出了一种动态激励下的光纤光栅应变传感器的校准方法。采用等强度悬臂梁模拟桥梁结构,在等强度悬臂梁末端瞬间悬挂不同重量的砝码来模拟桥梁上汽车产生的动态激励。以电阻应变片作为参考传感器,光纤光栅应变传感器作为待校准传感器,将这两个传感器的测量数据序列进行比对。针对传感器的测量数据序列出现的时间错位问题,采用互相关算法对参考传感器和待校准传感器的测量数据进行数据匹配。在光纤光栅应变传感器有初始值的情况下进行测量值校准的研究。实验结果表明,该方法有效解决了测量数据序列的时间错位问题,实现了光纤光栅应变传感器的动态校准,采用不同重量的砝码作为激励源对校准结果没有影响,1529 nm和1547 nm波长的光纤光栅应变传感器灵敏度校准系数与静态标定结果基本一致。     

光纤布拉格光栅与空芯光纤多模干涉混合型温度应变双参量传感器

针对光纤应变传感器由于温度敏感而引入的测量问题,提出了一种基于光纤布拉格光栅和空芯光纤多模干涉效应的混合型温度-应变双参量传感器。该传感器由两根单模光纤与一段内径小于单模光纤纤芯直径的空芯光纤熔接制成,其中一根单模光纤的光纤端面附近预刻一组光纤布拉格光栅。空芯光纤长度为厘米量级,光波以多模形式在空芯光纤侧壁中传播。结合光纤布拉格光栅和空芯光纤多模干涉效应对温度和应变的不同响应灵敏度,通过求解双参数耦合矩阵同时获取温度和应变两个参量,并有效解决了单个传感器在温度或应变测量时的温度-应变交叉敏感性问题。采用中心波长为1 550.172 nm的光纤布拉格光栅与一段长为2.5 cm、内径为5μm的空芯光纤制备了相应的传感器,并进行了温度和应变测试。结果表明,光纤布拉格光栅和空芯光纤的温度灵敏度分别达到10.530 6 pm/℃和1.802 1 pm/℃,应变灵敏度分别达到0.720 7 pm/με和1.243 2 pm/με。     

单光纤光栅波谱展宽温度压力同时区分测量

报道了利用单光纤布拉格光栅反射波带宽展宽技术实现温度与压力同时区分测量的新方案。通过聚合物材料将光栅粘接于双孔悬臂梁非均匀应变区 ,在压力作用下悬臂梁带动光栅发生非均匀应变 ,使布拉格反射波波长漂移的同时带宽展宽 ,而温度变化仅引起反射波波长漂移。在 2 0～ 10 0℃和 0～ 7.8N的温度和压力测量范围内 ,温度测量精度± 1.1℃ ,压力测量精度± 0 .18N ,布拉格反射波中心波长漂移量和带宽展宽量随温度和压力的变化呈良好的线性关系 ,线性度均高于 99.6 %。多次测量表明 ,此方案的展宽波形稳定 ,重复性好。     

用光纤光栅传感器测量外压力的动态调制方法

为了提高光纤布拉格光栅压力传感器的精度和降低系统成本，提出一种使用光纤双布拉格光栅测定压力的测量方法，即在外界压力作用下，传感光纤布拉格光栅反射波长的飘移被转变成在交变力策动下发生弯曲的等强度悬臂梁调制的扫描光栅的反射光脉冲间隔的变化。实验结果表明：光纤布拉格光栅反射波长漂移的测量范围为0～3nm，波长测量的不确定度为1pm；压力传感器的量程为0～6MPa时，压力的测量不确定度为0.005MPa。     

光纤布拉格光栅传感器应变传递双向耦合分析

粘贴于受弯基体表面的光纤布拉格光栅传感器测量应变与基体真实应变之间存在误差,因此研究光纤布拉格光栅传感器的变形机理、分析测量应变与真实应变之间的关系是目前的研究热点.首先研究光纤布拉格光栅传感器与基体之间的相互作用机理,然后,利用有限元解、实验值和理论解进行对比验证,并分析产生误差的原因.最后,通过参数分析研究弹性模量、厚度、粘结长度等参数对光纤布拉格光栅传感器测量效果的影响.结果表明有限元解、实验值和理论解具有相同的变化趋势,有限元解与理论解的误差在2%以内,测量值与理论解的误差在7%以内.平均应变传递率随着基体弹性模量的增大、粘结长度的增长而逐渐增大,随粘结层弹性模量的减小、粘结层厚度的增大而逐渐减小.该理论对应用于受弯基体应变测量的光纤布拉格光栅传感器的设计具有一定的指导意义.     

非本征型法布里-珀罗干涉仪光纤布拉格光栅应变温度传感器及其应用

介绍了光纤布拉格光栅非本征型法布里珀罗干涉仪集成复用传感器的结构、应变和温度同时监测的原理 ;观察到光纤布拉格光栅反射谱和非本征型法布里珀罗干涉仪干涉谱间的串扰 ,用 3dB带宽平均波长法减小了该串扰 ,提高了测量精度 ;将该传感器应用于三维编织复合材料的应变及温度同时监测。实验结果表明温度精度为± 1℃ ,应变精度为± 2 0 μ ,可满足实际应用的要求     

基于阵列波导光栅的智能服装人体测温解调系统研究

研究并实现了一种应用于智能服装中人体温度测量的阵列波导光栅解调系统。分析了系统的解调原理,搭建了光纤布拉格光栅解调实验平台,采用了强度法解调出光纤光栅的布拉格波长,完成了光纤光栅传感器串联前后解调的实验。结果表明,系统对光纤布拉格光栅的布拉格波长的解调具有高线性度,波长测量精度可达0.001 nm,光纤布拉格光栅传感器间串扰所造成的解调误差为0.000 5 nm,人体温度的测量误差为±0.16 ℃。该解调系统精度高、串扰低,可适用于智能服装中人体温度的测量。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.