液态五元Zr57Cu20Al10Ni8Ti5合金的微观结构演变与非晶形成机制

利用电磁悬浮无容器处理技术实现了液态五元Zr₅₇Cu₂₀Al₁₀Ni₈Ti₅合金的深过冷与快速凝固,同时通过分子动力学模拟计算揭示了非晶形成的微观机制.实验发现,凝固组织具有明显的核-壳结构特征,核区为非晶相,壳区主要由ZrCu, Zr₂Cu和Zr₈Cu₅晶体相组成.非晶体积分数随合金过冷度的升高逐渐增大,当达到实验最大过冷度300 K (0.26T_L)时,非晶体积分数增至81.3%.由此导出完全非晶凝固所需临界过冷度为334 K. TEM分析显示,过冷度增大并接近临界过冷度时,合金凝固组织中晶体相主要为Zr₈Cu₅相,而ZrCu和Zr₂Cu相的生长被抑制.在达到临界过冷度后,过冷液相的凝固路径由Zr₈Cu₅结晶生长转变为非晶凝固.此外,合金的晶体壳中存在少量的晶间非晶相,而非晶核中...     

铸锭凝固组织对相应非晶合金晶化过程中二十面体准晶相形成动力学的影响

通过在真空电弧熔炼炉内对合金铸锭进行反复熔炼处理，获得到了凝固组织不同的Zr₆₅Al_7.5Cu_12.5Ni₁₀Ag₅合金铸锭.在相同的制备条件下，由凝固组织不同的合金铸锭通过吸铸法制备得到了薄片非晶合金.利用差示扫描量热法(DSC)对非晶合金的晶化动力学进行了分析.x射线衍射谱表明，在Zr₆₅Al_7.5Cu_12.5Ni₁₀Ag₅非晶合金晶化过程中，二十面体准晶相(I相)作为初生相析出.Kissinger分析结果表明，合金铸锭的凝固组织细化，相对应的非晶合金发生晶化时，I相形成与分解的有效激活能都增大，说明非晶合金及析出的I相的热稳定性都提高.从结构的遗传性角度就合金铸锭凝固组织对相应非晶合金晶化过程中二十面体准晶相的形成动力学的影响进行了讨论. 关键词： 二十面体准晶相 晶化动力学 凝固组织     

压痕塑性变形诱导非晶合金的晶化

利用透射电镜研究了Zr₆₅Al_7.5Ni₁₀Cu_12.5Ag₅非晶合金的Vickers压痕内微观结构的变化. 结果发现，压痕塑性变形诱导非晶合金发生了晶化，在压头棱角下面的区域内有尺寸大于1 μm的晶体析出. 选区电子衍射分析表明，该析出相是稳定的CuZr₂或NiZr₂四方晶体，而没有析出该非晶合金在加热过程中的初生相二十面体准晶相,说明非晶合金的机械稳定性与热稳定性是有区别的. 打压痕过程中的温度升高是可以忽略的，本工作进一步证实了塑性变形诱导非晶合金晶化的主要动力是粘性流动而非局部热效应. 关键词： 非晶合金 塑性变形 粘性流动 局部热效应     

Zr60Al15Ni25大块非晶合金晶化动力学研究

通过等温示差扫描量热法研究了Zr₆₀Al₁₅Ni₂₅大块非 晶合金的晶化动力学.实验结果表明，晶化过程的孕育期很短，即使在743 K这样低的温度下也不过0.52 min，而放热峰宽（反应整个晶化过程进行的时间）却随退火温度的降低明显增大，这说明了结晶过程是一个晶核长大控制的过程.Avrami指数表明在不同的退火温度，该合金的晶化机制发生了变化.晶化机制的变化是由于合金原子在不同温度下的扩散能力相差很大所致. 关键词： 晶化动力学 60Al₁₅Ni₂₅大块非晶合金')" href="#">Zr₆₀Al₁₅Ni₂₅大块非晶合金 示差扫 描量热法（DSC）     

注入Mo 在Zr57Nb5Cu15.4Ni12.6Al10非晶合金中的扩散

通过二次离子质谱仪（SIMS）研究了Mo在Zr₅₇Nb₅Cu_15.4Ni_12.6Al₁₀非晶合金中的扩散，并计算出其扩散激活能Q和前置系数D₀分别为1.95 eV和1.13×10^-5m²s^-1.根据Stokes-Einstern关系式研究了玻璃转变温度以下593—673 K之间Zr₅₇Nb 关键词： 扩散 离子注入 二次离子质谱（SIMS） 黏滞特性     

压力对Zr46.75Ti8.25Cu7.5Ni10Be27.5大块非晶合金玻璃转变和晶化动力学的影响

利用X射线衍射和差示扫描量热分析研究了高温高压下Zr_46.75Ti_8.25Cu_7.5Ni₁₀Be_27.5大块非晶合金的玻璃转变和晶化行为，结果发现压力降低了该大块非晶合金中的自由体积、热焓和晶化激活能. 关键词： 大块非晶合金 高压 差示扫描量热分析 玻璃转变     

用原位x射线小角散射研究块体非晶合金Zr55Cu30Al10 Ni5的结构弛豫

应用同步辐射x射线小角散射法在原位对块体非晶合金Zr₅₅Cu₃₀Al ₁₀Ni₅在等温退火过程中的微结构变化进行研究.实验表明：在等温退火过程中电子 密度涨落反映了晶化之前的结构弛豫过程；在一定的退火温度下、随退火时间的增加，拓扑短程序弛豫与化学短程序弛豫之间存在一个电子密度均匀化的过程；导致这两种弛豫过程转变的退火时间与退火温度有关，温度越高，所需的退火时间越短. 关键词： 原位x射线小角散射 块体非晶合金 等温退火 结构弛豫     

非晶Fe73.5Cu1Nb3Si13.5B9合金激光纳米化的超精细结构研究

在CO₂激光功率为50—300W、扫描速度为20mm/s、激光散光斑为20mm照射条件下 ，诱导非 晶Fe_735Cu₁Nb₃Si_135B9带中发生结构重组，产生定量纳米α-F e(Si)晶相形成双相组织结构材料. 利用穆斯堡尔谱研究了非晶Fe_735C u₁Nb₃Si_135B₉合金激光纳米化的 超精细结构. 实验结果表明，激光诱导非晶 Fe_735Cu₁Nb₃Si_135B ₉纳米化后，其超精细磁场的分布随 着激光功率变 化由单峰向双峰变化，在高功率辐照时， 出现了双峰分布，并且峰位向高场移动. 高激光 功率辐照非晶Fe_735Cu₁Nb₃Si_{135B9合金纳米晶化相有四种超精细结 构，即2个超精细磁场较小的初晶相和2个超精细磁场较大的纳米晶化相. 其中超精细磁场较 大(17—25MA/m)的α-Fe(Si)相为DO3结构. 关键词： 激光 纳米晶α-Fe（Si) 735}Cu₁Nb< sub>3Si_135B₉')" href="#">非晶Fe_735Cu₁Nb< sub>3Si_135B₉ 超精细结构 超精细磁场     

Zr-Cu-Ni-Al-Nb大块非晶合金的晶化行为、力学性能及电化学腐蚀行为的研究

利用水冷铜模铸造法成功制备了Zr_65-xCu_17.5Al_7.5Ni ₁₀Nb_x (x=0，2，5)大块非晶合金. X射线衍射、热分析研究结果表 明，Nb的添加显著改变了非晶合金的晶化行为，促进了二十面体准晶相的形成. 各合金的准 静态压缩实验表明，Nb的适量添加有利于提高大块非晶合金的强度和塑性. 其中x=5的大块 非晶合金的抗压强度σ_b和塑性应变量ε_p 关键词： Zr基大块非晶合金 晶化行为 力学性能 耐腐蚀性能     

纳米超微晶Fe73.5Cu1Mo3Si13.5B9合金显微结构和磁性的研究

对纳米晶Fe_73.5Cu₁Mo₃Si_13.5B₉合金的原始制备态和各退火态样品进行了室温Mossbauer谱研究,结果表明晶化态的合金存在α-Fe(Si)微晶相和晶界的非晶相。晶相和非晶相内场和面积随退火温度的变化是退火时Cu,Mo,B等成分的扩散和在各相中的再分配引起的。最佳磁性能对应非晶相中的铁量占合金铁总量的30％左右,超微晶合金的双相无规各向异性模型表明,一定量的非晶相对保持纳米晶优异的软 关键词：     

三元Co_(79)Zr_(18)Cr_3合金中高矫顽力

通过在Co_(82)Zr_(18)合金中添加过渡族元素Cr的方法,利用快淬工艺,制备出了Co_(82-x)Zr_(18)Cr_x(x=0,2,3,4)快淬合金薄带,利用磁性测量、X光衍射、热磁分析、扫描电子显微镜,对其磁性能、相组成、微结构进行了研究,实验结果表明,在Co_(82)Zr_(18)合金中添加少量的Cr可以使其矫顽力(iHc)显著提高,其中,Co_(79)Zr_(18)Cr_3快淬薄带经600℃退火处理后iHc=6.5 kOe.相分析发现,600℃退火后的Co_(79)Zr_(18)Cr_3快淬薄带由单一Co_(11)Zr_2相组成,Cr原子进入到了Co_(11)Zr_2相的晶格之中替换了原子半径相对较小的Co原子,这导致了Co_(11)Zr_2居里温度(T_C)的降低却使其磁晶各向异性场(Ha)显著提高;另一方面,通过微结构研究发现,未退火的Co_(79)Zr_(18)Cr_3快淬薄带由50—80 nm的等轴晶粒组成,经600℃退火后,其晶粒形态并未发生改变然而晶粒尺寸却增长到400—500nm。     

Study of the interfacial structure and chemistry of CVD κ-Al2O3/TiC multilayer coatings

This article describes the interfacial regions in CVD grown TiC/κ-Al₂O₃ multilayers. A number of microanalytical techniques were used including HREM, EDX and EELS. Occasionally, the first 50 nm of the alumina layers deposited on the intermediate TiC layers grew as a cubic alumina, heavily faulted, containing small amounts of sulphur (S), maybe as a stabiliser. The presence of slightly rounded TiC (111) facets may act as preferred nucleation sites for the cubic Al₂O₃ phase, with a ‘cube on cube’ orientation relationship. In this way the nucleation of κ-Al₂O₃ is less favourable. After some tens of nanometres the cubic phase cannot be stabilised any longer and the layer continues to grow as κ-Al₂O₃. A number of observations point towards the reaction zone (RZ) being η- and/or γ-Al₂O₃. The diffraction work and the FFT analysis of the HREM images show that the RZ is an fcc phase with a=7.9 Å, which matches with η- and γ-Al₂O₃. The EELS Al fine structure indicate more tetrahedral Al ions than in κ-Al₂O₃, as in η- and γ-Al₂O₃. The RZ contains small amounts of S, as has been reported for γ-Al₂O₃. Due to the structural similarities between η- and γ-Al₂O₃ it was not possible to determine which of these cubic phases is present in the RZ.     

Structural and magnetic characterization of Co67Fe4Ni2Si15B12

 Soft magnetic properties of Co-based amorphous alloy of the composition Co₆₇Fe₄Ni₂Si₁₅B₁₂ have been investigated by isothermal heat treatment up to the conventional crystallization temperature. In the as-cast condition the Curie temperature of the sample is 272 °C and saturation magnetization is 74 emu/g. Magnetic properties undergo variation depending on the heat treatment temperature. For the heat treatment temperatures of around 420 and 490 °C, superior soft magnetic properties are obtained. For both the temperatures initial permeability, μ′ reaches value up to ten times the value of permeability in the as-received samples. Annealing effect on giant magneto-impedance has been observed for the current-driving frequencies of 4.5 and 6 MHz. Field dependence of magneto-impedance shows hysteresis at low field, which is related to the changes in the magnetization process of the sample.     

A STUDY OF THE CRYSTALLIZATION OF AMORPHOUS Cu60Zr40 ALLOY

The crystallization of the amorphous Cu₆₀Zr₄₀ alloy has been studied by differential scanning calorimetry (DSC), scanning Auger microprobe (SAM) and transmission electron microscopy (TEM). The DSC trace showed that the sample exhibited a glass transition at 750 K and a strong exothermic effect beginning from 782 K. An enrichment of the element Zr and significant oxygen contamination in a zone near the surface to a depth of about 10 nm were revealed by SAM in the analysis of surface competition and depth profiles of the Cu₆₀Zr₄₀ sample. Also, the change of concentration ratio of Ca to Zr in amorphous matrix at the clean Cu₆₀Zr₄₀ surface as a function of annealing temperature was examined in detail, and it was found that the concentration of Zr at the surface is slightly higher than that in the bulk until 780K and that the concentration ratio of Cu to Zr in matrix has an abrupt increase in the temperature range of 780-800K. The observations by high resolution TEM revealed the appearance of cluster-like regions of approximately 1.5-2.0 nm in size just before crystallization and they distributed randomly throughout the sample. This phenomenon is analogous to the results obtained using field ion microscopy (FIM) by the present authors. The microstructural changes of the sample daring heating show the gradual crystallization of the amorphous matrix.     

ZnSb掺杂的Ge2Sb2Te5薄膜的相变性能研究

本文采用双靶(ZnSb靶和Ge₂Sb₂Te₅靶)共溅射制备了系列ZnSb掺杂的Ge₂Sb₂Te₅(GST)薄膜. 利用X射线衍射、透射电子显微镜、原位等温/变温电阻测量、X射线光电子能谱等测试研究了薄膜样品的非晶形态、电学及原子成键特性. 利用等温原位电阻测试表明ZnSb掺杂的Ge₂Sb₂Te₅薄膜具有更高的结晶温度. 采用Arrhenius 公式计算发现ZnSb掺杂的Ge₂Sb₂Te₅薄膜的十年数据保持温度均高于传统的Ge₂Sb₂Te₅薄膜的88.9℃. 薄膜在200, 250, 300和350℃ 下退火后的X射线衍射图谱表明ZnSb的掺杂抑制了Ge₂Sb₂Te₅薄膜从fcc态到hex态的转变. 通过对薄膜的光电子能谱和透射电镜分析可知Zn, Sb, Te原子之间键进行重组, 形成Zn–Sb 和Zn–Te 键, 且构成非晶物质存在于晶体周围. 采用相变静态检测仪测试样品的相变行为发现ZnSb掺杂的Ge₂Sb₂Te₅薄膜具有更快的结晶速度. 特别是(ZnSb)_24.3(Ge₂Sb₂Te₅)_75.7薄膜, 其结晶温度达到250℃, 十年数据保持温度达到130.1℃, 并且在70 mW激光脉冲功率下晶化时间仅～64 ns, 远快于传统Ge₂Sb₂Te₅薄膜的晶化时间～280 ns. 以上结果表明(ZnSb)_24.3(Ge₂Sb₂Te₅)_75.7薄膜是一种热稳定性好且结晶速度快的相变存储材料.     

Magnetic phase transition in (Fe,Mn)65Ni35 alloys

Magnetization measurements on the Fe₆₀Mn₅Ni₃₅ and Fe₅₀Mn₁₅Ni₃₅ alloy samples were carried out in the temperature range 80T300 K and in magnetic fields up to 8 kOe. The Fe₆₀Mn₅Ni₃₅ was found to order ferromagnetically with a Curie temperature, T_c, above 300 K. From the temperature dependence of the spontaneous magnetization, M_s, it was concluded that the magnetic behavior of Fe₆₀Mn₅Ni₃₅ follows Wohlfarth theory of weak itinerant ferromagnet. The Fe₅₀Mn₁₅Ni₃₅ sample exhibits a magnetic phase transition from ferromagnetism to paramagnetism at T_c=242 K. The critical amplitudes and critical exponents (β, γ and δ) have been determined by using Arrott plots, Kouvel–Fisher method and scaling plots of the reduced magnetization and reduced magnetic field. The values of β, γ and δ are discussed and compared with the results obtained for various theoretical models and also with the experimentally determined values for related systems obtained by others.     

Origin of cathodic degradation and new phase formation at the La0.9Sr0.1MnO3/YSZ interface

New phase formation at the La_0.9Sr_0.1MnO₃/YSZ interface and its effects on the cathodic performances were studied at 900 °C in air. The resistance caused by the interfacial product layer kept increasing with time to reach up to 40% of the total resistance after 500 h. The interfacial product was identified as La₂Zr₂O₇ by XRD measurement. The electrical conductivity of La₂Zr₂O₇ (2.4 × 10⁻⁵ S cm⁻¹ at 1000 °C), measured by AC impedance and current interruption methods, was 4 to 7 orders of magnitude smaller than those of La_0.9Sr_0.1MnO₃ electrode or YSZ electrolyte. Either the electronic conductivity or the electrochemical O₂ reduction activity of La₂Zr₂O₇ was negligible. Combining these results, a conclusion was made that the cathodic degradation comes mainly from the growth of interfacial product layer and its contribution to the cell resistance increment is ohmic in nature.     

Properties of rubidium nitrate in ion-conducting RbNO3-Al2O3 nanocomposites

Properties of RbNO₃ in (1 − x)RbNO₃-xAl₂O₃ nanocomposites were studied by X-ray powder diffraction, electron diffraction, conductivity measurements, infrared and Raman spectroscopy, and differential scanning calorimetry. All the experimental techniques used indicate the presence of an amorphous RbNO₃ layer at the RbNO₃---Al₂O₃ interface in addition to a crystalline RbNO₃ phase. Its concentration was determined from the phase transition enthalpies. The amorphous layer thickness estimated by means of a simple brick-wall model is 4 nm.     

铀在Nd_2Zr_2O_7烧绿石中的固溶量及重离子辐照效应

Nd_2Zr_2O_7烧绿石因其稳定的物理化学性质和辐照稳定性可以作为高放废物中锕系核素的固化基材.通过溶胶凝胶—喷雾热解—高温烧结方法制备了含铀的Nd_2Zr_2O_7烧绿石固化体;开展了Nd_2Zr_2O_7和Nd_(1.9)U_(0.1)Zr_2O_7固化体的重离子辐照实验,辐照剂量为1 dpa和3 dpa;利用X射线衍射和Raman光谱对固化体结构进行了分析.研究发现铀在Nd_2Zr_2O_7烧绿石体系的固溶量仅为10 at%,高价态铀掺杂导致固化体结构向无序化转变.重离子辐照实验表明, Nd_2Zr_2O_7烧绿石基材具有较高的抗辐照稳定性;而Nd_(1.9)U_(0.1)Zr_2O_7在较低辐照剂量下,固化体烧绿石体系结构破坏,重离子辐照诱导固化体结构转变为更加无序化的萤石结构.低固溶量和抗辐照能力减弱主要是由于锕系核素烧绿石固化体的结构无序化所致.     

Substrate dependent growth studies of MgB2 films by electrocrystallization

The comparative study of MgB₂ film growth on Al₂O₃ and glass substrate by electrocrystallization technique is discussed. The precursor magnesium films were deposited by vacuum evaporation method. These magnesium films were then used as electrode for the growth of MgB₂ films by electrocrystallization. The structural, morphological and superconducting properties of the electrocrystallized MgB₂ films on Al₂O₃ substrate were examined by using XRD, SEM and electrical resistivity measurement techniques and compared with that of MgB₂ films grown on glass substrate. The films deposited on Al₂O₃ substrates showed enhanced crystallinity and relatively higher T_c value compared to films deposited on glass substrates.