萤石结构TiO2的电子结构和光学性质

利用第一性原理计算了立方相萤石TiO₂的晶胞参数，能带结构和电子态密度.结果显示萤石TiO₂属于间接带隙半导体材料，其间接禁带宽度(Γ→X)E_g为2.07eV，比常见的金红石和锐钛矿TiO₂的禁带宽度窄.为了更清楚地了解萤石的光学性质，利用Kramers-Kronig色散关系，分别对萤石和金红石TiO₂的复介电常数、吸收率等参数进行了计算，并将二者结果做了     

Sr和Ba替代对Eu掺杂Ca2.955Si2O7的结构和发光特性的影响研究

利用固相反应法制备了Sr和Ba替代的Ca_2.955-xM_xSi₂O₇: 0.045Eu²⁺ (M= Sr, Ba, x= 0.1-0.5)系列荧光粉, 利用较大离子半径的Sr和Ba元素替代Eu掺杂Ca_2.955-xM_xSi₂O₇ 中的Ca元素,研究Sr和Ba替代对样品结构和发光特性的影响. X射线衍射测试结果表明,少量Sr和Ba替代不会改变基质的晶体结构, 样品仍然为单斜晶系.未替代前, Ca_2.955Si₂O₇: 0.045Eu²⁺ 样品的发射峰在574 nm左右,随着Sr含量的增加,样品的发射峰发生蓝移; 而Ba含量在x= 0.1-0.4时不会引起发射峰位置的移动, 但x= 0.5样品的发射峰发生蓝移.同等含量的Sr和Ba部分替代样品中的Ca元素, Ba替代样品的光谱强度较强.     

射频磁控溅射法制备SnO2:Sb薄膜的结构和光致发光性质研究

采用射频磁控溅射法在玻璃衬底上制备出锑掺杂的氧化锡（SnO2₂:Sb）薄膜.制 备薄膜是具有纯氧化锡四方金红石结构的多晶膜薄，晶粒生长的择优取向为［110］.室温下光致发光测量结果表明，在392nm附近存在强的紫外-紫光发射.研究了不同氧分压对薄膜结构及发光性质的影响，并对SnO2₂:Sb的光致发光机制进行了探索性研究.     

Photocatalytic Activity of N-doped TiO2 Photocatalysts Prepared from the Molecular Precursor (NH4)2TiO(C2O4)2

用不同温度控制分解草酸氧钛铵制备N掺杂TiO₂光催化剂．利用XRD、IR、热分析、N₂吸-脱附等温线、XPS、紫外可见漫反射光谱和SEM表征了N-TiO₂光催化剂的结构．400～600 oC焙烧的N-TiO₂光催化剂为纯锐钛矿相,而700 oC焙烧的N-TiO₂光催化剂为锐钛矿和金红石混合相．N掺杂在TiO₂的间隙位使锐钛矿相TiO₂带隙变窄．在光降解甲基橙的反应中,600和400 oC焙烧的N-TiO₂催化剂分别在紫外光和全波长光照射下有最好活性;700 oC焙烧的N-TiO₂催化剂无论在紫外光和全波长光下都表现出最好的比活性,即最高的光量子效率,这可以归因于700 oC焙烧的N-TiO₂光催化剂良好的结晶程度和锐钛矿-金红石异相结的存在．     

Eu2+, Cr3+共掺杂的MAl12O19 (M=Ca, Sr, Ba) 的发光性质及能量传递

三基色荧光粉中, 红色荧光粉性能较差, 为获得性能优良的红色荧光粉, 本文采用高温固相法合成了Eu²⁺, Cr³⁺单掺杂及共掺杂的碱土金属多铝酸盐MAl₁₂O₁₉ (M =Ca, Sr, Ba) 发光体. 实验表明, 在以上三种基质中均存在Eu²⁺→Cr³⁺的能量传递, 利用能量传递可以有效将Eu²⁺的蓝光或绿光转换为红光. 三种碱土金属多铝酸盐基质的晶体结构相似,但Eu²⁺, Cr³⁺发光受晶体场影响,导致在不同的基质中Eu²⁺, Cr³⁺间能量传递效率不同.通过光谱分析及能量传递效率计算发现, 相同掺杂浓度下,CaAl₁₂O₁₉中Eu²⁺→Cr³⁺的能量传递效率最高,SrAl₁₂O₁₉次之, BaAl₁₂O₁₉最低.红光转换率在CaAl₁₂O₁₉中最高.     

第一性原理计算高压下金红石TiO2的结构不稳定性及热学性质

采用第一性原理计算研究了金红石TiO₂结构在高压下的不稳定性及热力学性质. 计算的高压下结构参数和零压的声子色散曲线与实验数据十分吻合. 进一步模拟了在不同压力下的声子曲线,在压力下,声子曲线不断软化,?点附近的振动频率不断减小直至虚频,意味着结构的不稳定,根据计算的不同压力下的弹性常数获得了其力学不稳定性,结果表明金红石结构TiO₂在压力高于17.7 GPa时变得不稳定. 根据准谐近似,获得了金红石TiO₂结构的热力学性质,计算结果与现有     

富勒烯掺杂NPB空穴传输层的有机电致发光器件

报道了不同掺杂浓度NPB：C₆₀（富勒烯）作为空穴传输层对有机电致发光器件性能的影响.采用真空热蒸镀方法,制作了ITO/ NPB：C₆₀ （x % ）/Alq₃/LiF/Mg:Ag结构的四种有机电致发光器件.当NPB：C₆₀的掺杂浓度是15％时,器件的启亮电压是4 V,最大亮度是11000 cd/m².然而,当NPB：C₆₀的掺杂浓度是20％时,器件的最大亮度降     

蓝宝石衬底SnO2:Sb薄膜的制备及结构和光致发光性质

用射频磁控溅射法在蓝宝石(0001)衬底上制备出锑掺杂的氧化锡(SnO₂:Sb)薄膜.对制备薄膜的结构和发光性质进行了研究.制备样品为多晶薄膜，具有纯SnO₂的四方金红石结构.室温条件下对样品进行光致发光测量，在334 nm附近观测到紫外发射峰，并对SnO₂:Sb的光致发光机制进行了研究.     

过渡金属(Fe,Co,Ni,Zn)掺杂金红石TiO2的电子结构和光学性质

采用基于密度泛函理论的第一性原理方法对未掺杂以及不同浓度过渡金属Fe,Co,Ni,Zn掺杂金红石TiO₂的超晶胞体系进行了几何优化,并讨论了其晶格常数,电子能带结构和光学性质.研究结果表明:掺杂前后的晶格参数与实验值偏差在3.6%以下;适量的过渡金属掺杂不但影响体系能带结构,拓宽光吸收范围,而且扮演着俘获电子的重要角色,有利于光生电子-空穴对的有效分离以及增强光吸收能力;Fe,Co,Ni,Zn最佳理论掺杂体系分别为Ti_0.75Fe_0.25O₂,Ti_0.75Co_0.25O₂,Ti_0.75Ni_0.25O₂,Ti_0.83Zn_0.17O₂;Fe,Co,Ni3d态分裂为t_2g和e_g态,分别贡献于价带高能级和导带低能级部分,促进了电子-空穴对的生成,从而可提高TiO₂的光催化性能;Zn3d态电子成对填满轨道,不易被激发,故光催化活性无明显提高.     

氮气退火对二氧化钛薄膜光学性能的影响

 提出了一种利用离子注入和后续退火制备氮掺杂TiO₂薄膜的方法。首先在室温下向石英玻璃中注入Ti离子,随后在氮气中退火到900 ℃,从而制备了氮掺杂的玻璃基TiO₂薄膜。SRIM2006程序模拟和卢瑟福背散射谱（RBS）研究表明注入离子从样品表面开始呈高斯分布,实验结果和模拟结果吻合很好。X射线光电子能谱（XPS）研究结果表明注入态样品中形成了金属Ti和TiO₂,900 ℃退火后金属Ti转变成TiO₂,同时N原子替代少量的晶格O原子形成了O－Ti－N化合物。紫外-可见吸收光谱（UV-Vis）结果显示,当退火温度至500 ℃时,在吸收光谱中开始出现TiO₂的吸收边,随退火温度升高到900 ℃,由于O－Ti－N化合物形成,TiO₂的吸收边从3.98 eV红移到3.30 eV,TiO₂吸收边末端延伸到可见光区,在可见光区的吸收强度明显增加。     

Analysis of hydrogen adsorption in the bulk and on the surface of magnesium nanoparticles

The stability of magnesium hydride (MgH _x ) nanoparticles (x = 0.5, …, 2) is investigated using ab initio calculations. It is shown that for a nanoparticle diameter of D ～ 5 nm, the internal pressure becomes lower than 3 kbar; for this reason, the structure of hydride nanoparticles coincides with the structure of this hydride in crystalline form. It is found that the phase of partly saturated MgH _x hydrides (x < 2) must decompose into the phase of pure hcp magnesium and the α phase of MgH₂. The frequencies of jumps of hydrogen atoms within the hcp phase of magnesium and in the α phase of MgH₂ are calculated; it is shown that slow diffusion of hydrogen in magnesium is due to the large height of potential barriers for motion of hydrogen within MgH₂. To attain high diffusion rates, the structures of Mg₅₃Sc and Mg₅₃Ti crystals and their hydrides are calculated. It is found that the frequency of jumps of H atoms in Mg₅₃ScH₁₀₈ near the Sc atoms does not noticeably change as compared to the frequency of jumps in the α phase of MgH₂, while the frequency of jumps in Mg₅₃TiH₁₀₈ near Ti atoms is higher by approximately a factor of 2.5 × 10⁶. This means that diffusion in manganese hydride with small admixtures of titanium atoms must be considerably eased. Chemical dissociation of hydrogen molecules on the (0001) surface of hcp magnesium, on the given surface with adjoined individual Ti atoms, and on the surface of a one-layer titanium cluster on the given surface of magnesium is investigated. It is found that dissociation of hydrogen at solitary titanium atoms, as well as on the surface of a Ti cluster, is facilitated to a considerable extent as compared to pure magnesium. This should also sharply increase the hydrogen adsorption rate in magnesium nanoparticles.     

萤石结构TiO2的电子结构和光学性质

利用第一性原理计算了立方相萤石TiO₂的晶胞参数,能带结构和电子态密度.结果显示萤石TiO₂属于间接带隙半导体材料,其间接禁带宽度(Γ→X)E_g为2.07eV,比常见的金红石和锐钛矿TiO₂的禁带宽度窄.为了更清楚地了解萤石的光学性质,利用Kramers-Kronig色散关系,分别对萤石和金红石TiO₂的复介电常数、吸收率等参数进行了计算,并将二者结果做了 关键词： 2')" href="#">萤石结构TiO₂ 密度泛函理论 能带结构 光学性质     

Structural, magnetic and electronic structure studies of Mn doped TiO2 thin films

We report structural, magnetic and electronic structure study of Mn doped TiO₂ thin films grown using pulsed laser deposition method. The films were characterized using X-ray diffraction (XRD), dc magnetization, X-ray magnetic circular dichroism (XMCD) and near edge X-ray absorption fine structure (NEXAFS) spectroscopy measurements. XRD results indicate that films exhibit single phase nature with rutile structure and exclude the secondary phase related to Mn metal cluster or any oxide phase of Mn. Magnetization studies reveal that both the films (3% and 5% Mn doped TiO₂) exhibit room temperature ferromagnetism and saturation magnetization increases with increase in concentration of Mn doping. The spectral features of XMCD at Mn L_3,2 edge show that Mn²⁺ ions contribute to the ferromagnetism. NEXAFS spectra measured at O K edge show a strong hybridization between Mn, Ti 3d and O 2p orbitals. NEXAFS spectra measured at Mn and Ti L_3,2 edge show that Mn exist in +2 valence state, whereas, Ti is in +4 state in Mn doped TiO₂ films.     

Étude par rmn de la localisation et des mouvements des protons dans les hydrures MgH2 et Mg2NiH4

Wide line and pulsed NMR studies are reported for MgH₂; and Mg₂NiH₄ hydrides at 79 and 30 MHz in the temperature range between 100 and 500 K. Line shape data confirm a rutile type structure for MgH₂, and lead to the evaluation that 97% of the hydrogen is present in this phase, the remainder being in solid solution MgH_x, (x<0.04).Mg₂NiH₄ shows a Gaussian line, whose peak-to-peak width decreases from 6.16 to 4.28 G in the range 320–365 K. From 365 to 480 K the spectrum shows a second, narrower, line (0.85 G), implying that approximately 7% of the protons have migrated from their initial position to energetically less stable sites. The thermal behaviour of the T₁ and T₂ relaxation times shows a dramatic variation in the 320–370 K temperature range in connection with the change of the proton localization. Relaxation mechanisms can be attributed mainly to conduction electron-nucleus interactions. With rising temperature, diffusion mechanisms are also involved. A diffusion activation energy of about 0.35 eV has been determined, with a diffusion coefficient 3.45 × 10^?8 < D < 4.6 × 10^?8 cm²/s.     

Ba0.5Sr0.5TiO3有序构型的第一性原理研究

采用第一性原理计算了Ba_0.5Sr_0.5TiO₃三种有序构型的晶格结构和对应的电子结构,晶格结构的详细分析结果表明BST{100}有序构型为四方相,Ti-O八面体中Ti原子和Ba-Sr平面上的O原子沿[100]方向分别偏心位移0.040 Å和0.065 Å,八面体畸变导致反平行自发极化出现,构型处于反铁电态. BST{110}构型也是四方相,并且(110)和(1 关键词： 钛酸锶钡 第一性原理 有序结构 铁电性     

Energetics and electronic properties of Mg7TMH16 (TM=Sc, Ti, V, Y, Zr, Nb): An ab initio study

First-principles calculations have been performed on the face-centered cubic (FCC) magnesium-transition metal (TM) hydrides Mg₇TMH₁₆ (TM=Sc, Ti, V, Y, Zr, Nb). The cohesive energies are calculated to analyze the stability, and the obtained enthalpies of formation for hydrides Mg₇TMH₁₆ have been used to investigate the possible pathways of formation reaction. The calculated enthalpy changes show that the decomposition temperatures of Mg₇TMH₁₆ are lower than that of MgH₂. The electronic densities of states reveal that all the hydrides studied here exhibit metallic characteristics. The bonding nature of Mg₇TMH₁₆ is investigated, showing stronger covalent bonding between TM and H than between Mg and H.     

Mg-TM-H (TM=Sc,Ti, V,Y, Zr,Nb)晶体形成能力和电子性能

基于密度泛函理论的第一性原理的Vienna Ab initio Simulation Package (VASP)软件系统研究了Mg₇TMH₁₆ (TM=Sc, Ti, V, Y, Zr, Nb)的晶体结构和电子性能. 分析了结合能和形成焓,计算得到的结合能显示Mg₇TiH₁₆和Mg₇NbH₁₆的稳定性最强,形成焓的变化表明Mg₇TMH₁₆具有比MgH₂更低的分解温度,电子态密度显示Mg₇TMH₁₆表现出明显的金属特性. 关键词： 第一原理 7TMH₁₆ (TM=Sc,Ti,V,Y,Zr,Nb)')" href="#">Mg₇TMH₁₆ (TM=Sc,Ti,V,Y,Zr,Nb) 结合能 形成焓     

The impact of ambient gas on the magnetic properties of Ti40Zr40Ni20 powders during mechanical alloying

Ti₄₀Zr₄₀Ni₂₀ in the form of elemental powders was mechanically alloyed in a planetary ball-mill under argon and hydrogen atmospheres at an acceleration of 55 m s^?2 for different time intervals. The samples were analyzed by X-ray diffraction (XRD), vibrating-sample magnetometry (VSM) and scanning electron microscopy (SEM), which revealed the large impact of the ambient gas, i.e. argon and hydrogen, on the magnetic properties, morphology and structure. Namely, during mechanical alloying in argon the saturation magnetization decreased due to the modification of the Ni d-states upon alloying with paramagnetic Ti and Zr, whereas in hydrogen the Ni d-states remained largely unmodified, since the formation of TiH₂ and ZrH₂ was faster than the alloying with the ferromagnetic nickel. However, after 40 h we obtained a mixture of nanocrystalline Ni and ZrH₂/TiH₂ hydrides, which in equilibrium contained 1.55 mass% of hydrogen. In the case of argon we determined welding of the Ti₄₀Zr₄₀Ni₂₀ amorphous particles, whereas in hydrogen such a process was suppressed by the brittle ZrH₂/TiH₂ hydrides. In addition, we revealed that the mechanical alloying of pure Ni powder for 100 h in argon does not affect its magnetic properties.     

Mechanically alloyed metal hydride systems

Mechanosynthesis of metal hydrides is a new field in which important progress has been reported. In this paper, we present recent developments in mechanosynthesis of magnesium-based hydrides for storage applications. The effect of intense milling on magnesium and magnesium hydrides is presented. The influence of various additives on hydrogen-sorption properties is discussed with special emphasis on nanocomposite MgH₂+5 at. % V, where hydrogen-storage characteristics, cycling properties and the mechanism of hydrogen desorption are presented. The production of novel nanocrystalline porous structures by mechanical alloying followed by a leaching technique is discussed. Hot ball-milling, as a new method for rapid synthesis of alloys, is also presented. Finally, two other methods of production of metal hydrides are discussed. One is reactive milling where metal hydrides are synthesized by mechanical alloying under hydrogen pressure, while the other is milling elemental hydrides to produce complex hydrides. Received: 15 August 2000 / Accepted: 6 November 2000 / Published online: 9 February 2001