金属玻璃Pd79.5Ni4Si16.5结晶化过程的慢正电子束研究

首次用单能慢正电子束研究金属玻璃的晶化过程.测量了金属玻璃Pd_79.5Ni₄Si_16.5淬火态、结构弛豫和结晶化状态样品的正电子湮没辐射多普勒展宽能谱与正电子入射能量的函数关系,结果表明,淬态金属玻璃Pd_79.5Ni₄Si_16.5中存在大量的空位型缺陷,其结晶化过程最先开始于表面层.单能慢正电子束是研究金属玻璃晶化过程的有效手段.     

中频磁脉冲处理Fe52Co34Hf7B6Cu1非晶合金的正电子湮没研究

对熔体急冷法制备的非晶合金 Fe₅₂Co₃₄Hf₇B₆Cu₁ 进行了不同频率的中频磁脉冲处理, 用透射电子显微镜、穆斯堡尔谱、正电子湮没寿命谱等方法研究了处 理前后试样的微观结构及结构缺陷变化. 结果表明,经中频磁脉冲处理后,样品发生了部分纳米晶化, 晶化量随磁脉冲频率增加而增加, 当磁脉冲频率为2000 Hz时, 晶化量达33.1%; 在淬态非晶样品中, 正电子在类单空位中的湮没寿命τ₁为150.5 ps, 强度 I₁为77.7%, 在微孔洞中的湮没寿命τ₂为349.7 ps,强度I₂为22.3%; 随磁脉冲频率的增加, τ₁, τ₂值呈现减小的变化趋势, 与淬态非晶相比, I₁有所增加, I₂下降, τ₁, τ₂的平均值τ大幅降低.     

非晶合金Fe73.5Cu1Nb3Si13.5B9的激波晶化及其特征

 研究了非晶合金Fe_73.5Cu₁Nb₃Si_13.5B₉（FINEMET）的激波晶化。与退火晶化比较,激波晶化具有一系列鲜明特征,这些特征是固态下扩散性相变理论难以解释的,有深刻的物理内涵。     

Fe78B13Si9、(Fe0.99Mo0.01)78B13Si9非晶合金的激波晶化实验研究

 研究了Fe₇₈B₁₃Si₉、(Fe_0.99Mo_0.01)₇₈B₁₃Si₉非晶合金的激波晶化行为。激波是由氢-氧爆炸产生的。实验结果表明：激波能使非晶合金在微秒时间内晶化,晶化主相为α-Fe基固溶体,次晶化相为Fe₃Si,且观察到α-Fe基因溶体晶格常数变小。用DTA分析进一步证实：激波晶化是比较完全的,晶化相相当稳定。     

Sr和Ba替代对Eu掺杂Ca2.955Si2O7的结构和发光特性的影响研究

利用固相反应法制备了Sr和Ba替代的Ca_2.955-xM_xSi₂O₇: 0.045Eu²⁺ (M= Sr, Ba, x= 0.1-0.5)系列荧光粉, 利用较大离子半径的Sr和Ba元素替代Eu掺杂Ca_2.955-xM_xSi₂O₇ 中的Ca元素,研究Sr和Ba替代对样品结构和发光特性的影响. X射线衍射测试结果表明,少量Sr和Ba替代不会改变基质的晶体结构, 样品仍然为单斜晶系.未替代前, Ca_2.955Si₂O₇: 0.045Eu²⁺ 样品的发射峰在574 nm左右,随着Sr含量的增加,样品的发射峰发生蓝移; 而Ba含量在x= 0.1-0.4时不会引起发射峰位置的移动, 但x= 0.5样品的发射峰发生蓝移.同等含量的Sr和Ba部分替代样品中的Ca元素, Ba替代样品的光谱强度较强.     

高压处理对Cu75.15Al24.85合金组织与电阻率的影响

本文借助金相显微镜, XRD, SEM和DSC等手段对Cu_75.15Al_24.85合金经1-5 GPa压力, 750℃保温15 min处理前后的组织结构进行了分析,并用电阻率测试仪对合金的 电阻率进行测试,以此探讨了高压处理对Cu_75.15Al_24.85合金组织与电阻率的影响. 结果表明:高压处理能细化Cu_75.15Al_24.85合金的组织,增大合金的电阻率, 当压力为3 GPa时,该合金获得的组织最细小,电阻率最大.     

Si1-xGex合金半导体中CiCs和CiOi缺陷随Ge含量的变化

采用从头计算(ab initio)的方法对Si和Si_1-xGe_x合金半导体材料中C_iC_s缺陷的性质进行探讨，同时也对比调查了C_iO_i缺陷在Si和Si_1-xGe_x合金中的性质. 在不同Ge含量的Si_1-xGe_{x相似文献}   

Si3N4的晶体化和ZrN/Si3N4纳米多层膜的超硬效应

研究了Si₃N₄层在ZrN/Si₃N₄纳米多层膜中的晶化现象及其对多层膜微结构与力学性能的影响. 一系列不同Si₃N₄层厚度的ZrN/Si₃N₄纳米多层膜通过反应磁控溅射法制备. 利用X射线衍射仪、高分辨透射电子显微镜和微力学探针表征了多层膜的微结构和力学性能. 结果表明，由于受到ZrN调制层晶体结构的模板作用，溅射条件下以非晶态存在的Si₃N₄层在其厚度小于0.9 nm时被强制晶化为NaCl结构的赝晶体，ZrN/Si₃N₄纳米多层膜形成共格外延生长的柱状晶，并相应地产生硬度升高的超硬效应. Si₃N₄随层厚的进一步增加又转变为非晶态，多层膜的共格生长结构因而受到破坏，其硬度也随之降低.     

Y对Fe-Si-B 合金非晶形成能力及软磁性能的影响

本文通过铜模吸铸法和单辊甩带法分别制备出一系列楔形试样和非晶条带试样, 系统研究了稀土金属Y对Fe₇₈Si₉B₁₃合金非晶形成能力及其软磁性能的影响. 结果表明, 少量Y取代 Fe-Si-B 非晶合金中的Fe 可大大提高该合金的非晶形成能力并促进过冷液相区的产生. 当Y含量为3 at.%时, 合金具有最大的非晶形成能力, 其临界厚度为313 μm, 相应的非晶过冷液相区宽度达到65 K. 该系列非晶合金具有优良的软磁性能, 其矫顽力(H_c)均低于200 A/m, Y含量为1 at.%时, 饱和磁感应强度(B_s) 达到最大值1.67 T.     

应变Ge/Si1-xGex 价带色散模型

基于k·p微扰理论, 通过引入应变哈密顿量作为微扰, 建立了双轴应变Ge/Si_1-xGe_x价带色散关系模型. 模型适于任意晶向弛豫Si_1-xGe_x虚衬底上的应变Ge价带结构, 通过该模型可获得任意k方向应变Ge的价带结构和空穴有效质量. 模型的Matlab模拟结果显示, 应变Ge/Si_1-xGe_x价带带边空穴有效质量随Ge组分的增加而减小, 其各向异性比弛豫Ge更加显著. 本文研究成果对Si基应变Ge MOS器件及集成电路的沟道应力与晶向的设计有参考价值.     

Ultraviolet photoelectron spectroscopy of Pd-Si glasses

In order to determine systematic changes in the density of states with alloy composition, photoelectron spectra at hv=21.2 eV were measured for several amorphous alloys based on the well-known Pd-Si glass system. Three binary alloys with 15, 20, and 25 at. % Si, two ternaries, Pd₈₀ Si₁₇ Cu₃ and Pd₈₀ Si₁₄ Cu₆, and polycrystalline Pd were analyzed. Compared to Pd, both the density of states at the Fermi energy and the d-band width are reduced in the glasses. The d-bands display an overall shift of 0.4 eV over the range of alloy compositions studied. Partial agreement with recent density of states calculations was obtained.     

Solidification mechanism transition of liquid Co–Cu–Ni ternary alloy

We report a solidification mechanism transition of liquid ternary Co₄₅Cu₄₅Ni₁₀ alloy when it solidifies at a critical undercooling of about 344 K. When undercooling at ΔT<344 K, the solidification process is characterized by primary S (Co) dendritic growth and a subsequent peritectic transition. The dendritic growth velocity of S (Co) dendrite increases with the rise of undercooling. However, once ΔT>344 K, the solidification velocity decreases with the increase of undercooling. In this case, liquid/liquid phase separation takes place prior to solidification. The minor L₂ (Cu) droplets hinder the motion of the solidification front, and a monotectic transition may occur in the major L₁ phase. These facts caused by metastable phase separation are responsible for the slow growth at high undercoolings.     

中子辐照对Pd80Si20与Pd77.5Cu6Si16.5非晶态合金结构的影响

本工作用X射线衍射技术示差扫描量热法(DSC)和内耗测量等手段研究金属-类金属非晶态合金Pd₈₀Si₂₀和Pd_77.5Cu₆Si_16.5中子辐照前后的微观结构变化。结果表明,辐照在两种样品的对关联函数g(r)以及径向分布函数RDF(r)上都引起明显的变化;辐照后样品的晶化温度和晶化热有所提高,结构变得更加无序,Pd₈₀Si₂₀非晶态合金的内耗在T关键词：     

On the level of mechanical loss in metallic glasses

Metallic glass samples with compositions Zr₆₅Al_7.5Cu_27.5 and Pd₇₇Cu₆Si₁₇, for which loss factors of up to 10^-2 have been reported, are reinvestigated with an electrostatic vibrating cantilever technique that detects dissipation factors tan δ as low as 10^-4. It is found that tan δ ≈ 4×10^-4 is a typical value for these alloys well below T _g , suggesting that previous results were limited by instrumental resolution. While aging the glasses increases their elastic moduli considerably, the measured loss factor is affected only marginally by thermal history.     

Structural phase transitions in Pd0.8 Si0.2 and Pd0.75 Si0.20 Ag0.05 alloys observed by pac

The phase transition in the alloys Pd_0.8 Si_0.2 and Pd_0.75 Si_0.20 Ag_0.05 have been investigated through the quadrupole interaction of¹¹¹Cd impurities. The quadrupole interactions were measured by means of the TDPAC technique from room temperature up to about 870 K. The variation of the quadrupole interaction with temperature in the alloy PdSiAg shows aT ^3/2 dependence below and above 629 K, with coefficientsB=5.43(25)·10⁻⁵ K^−3/2 andB=3.70(15)·10⁻⁵ K^−3/2, respectively. This demonstrates that the alloy undergoes a phase transition around 629 K. The existence of two electric field gradients observed in the alloy PdSi,V _zz (1)=3.47(54)·10¹⁷ V/cm² andV _zz (2)=2.29(36)·10¹⁷ V/cm², indicates that there are two different¹¹¹Cd sites. The corresponding fractionsf ₁ andf ₂ strongly depend on temperature. Below 520 K, most¹¹¹Cd nuclei are subject to the higher EFGV _zz (1) (f ₁≈70%), whereas above 520 Kf ₁ falls rapidly to zero andV _zz (2) becomes dominant. The temperature dependences of thef ₁ andf ₂ reveal a picture of the phase transition between the two crystal structures.     

Mössbauer study of microstructure of new soft magnetic microcrystalline Fe78.1Cu1.2Nb3.2Si12.5B10.0 alloy

The microstructure of microcrystalline Fe_78.1Cu_1.2Nb_3.2Si_12.5 B₁₀ alloy was examined by Mossbauer effect. The experimental results have shown that the microstructure of the alloy is composed of about 70% the ordered phase Fe_75+ySi_25−y, 26% amorphous phase as grain boundaries and a little paramagnetic phase. y in Fe_75+ySi_25−y has preliminaryly determined to be in the range of 5–7.     

深过冷Ag-Cu-Ge三元共晶合金的相组成与凝固特征

在Ag_38.5Cu_33.4Ge_28.1三元共晶合金的深过冷实验中，获得的最大过冷度为175 K(0.22T_E). XRD分析表明，不同过冷条件下其共晶组织均由(Ag),(Ge)和η(Cu₃Ge)三相组成. 在小过冷条件下，三个共晶相协同生长，凝固组织粗大.随着过冷度的增大，共晶组织明显细化，(Ge)相与其他两相分离，以初生相方式生长，而(Ag)相与η相始终呈二相层片共晶方式共生生长. 当过冷度超过80 K时，初生相(Ge)由小过冷时的块状转变为具有小面相特征的枝晶方式生长. 部分小面相(Ge)枝晶出现规则的花状，花瓣数介于5—8之间，并且过冷度越大(Ge)相越容易分瓣. 花状(Ge)枝晶的晶体表面为{111}晶面簇，择优生长方向为〈100〉晶向族. 关键词： 三元共晶 晶体形核 深过冷 快速凝固     

Thermopower of some amorphous transition metal-alloys

Measurements of the thermopower for amorphous alloys are reported in the temperature range 77K to 320K. The alloys examined are Cu₅₀Ti₅₀, Pd₈₀Si₂₀, Pd₃₀Zr₇₀ and Cu₄₀Zr₆₀. The data are compared with values of similar systems, as far as available. In addition we analyse the temperature coefficient of the thermopower, applying a model, based on the Ziman formulation of the transport properties.     

Influence of stress and temperature on damping behavior of amorphous Pd77.5Cu6.0Si16.5 below Tg

In this work we analyzed the mechanical damping behavior of amorphous Pd_77.5Cu_6.0Si_16.5 below the glass transition temperature (T _g) with creep/recovery measurements. Here a correlation between temperature stimulation and external stress is found in an exponential, multiplicative way. This demonstrates that not only is the yield stress of the material influenced by temperature variation (mechanical melting) but also the secondary relaxation is modified under stress and temperature.     

静高压下Cu-Si块状纳米合金的制备与表征

 用压淬的方法，在6 GPa静高压下，以200 K/s的冷却速率冷却熔融状态的Cu₇₀Si₃₀合金，制备出块状Cu-Si纳米合金．X射线衍射和透射电子显微镜分析表明：该纳米合金由γ-Cu₅Si和一未知相组成，未知相为简单立方晶体，晶格常数α₀=0.853 5 nm，其热力学状态为亚稳态。并对静高压下块状纳米合金的形成机理进行了探讨。