化学气相沉积法中SnO2一维纳米结构的控制生长

以Sn和SnO为源材料，化学气相沉积法中通过控制反应物配比及载气中的氧含量等宏观实验条件，实现了SnO₂一维纳米结构的控制生长，成功获得各种不同横向尺度的SnO₂纳米线、纳米带以及直径连续变化的针状纳米结构. 通过扫描电子显微镜、X射线衍射仪对不同实验条件下所制备的样品进行形貌和晶格结构表征，认为高温生长点附近锡与氧的相对含量是控制SnO₂一维纳米结构生长的关键因素；并在此基础上对SnO₂一维纳米结构的生长机理进行了深入的讨论.     

1,2-丙二醇辅助溶胶凝胶法制备NASICON型Li1.3Al0.3Ti1.7(PO4)3固体电解质

通过1,2-丙二醇辅助的溶胶凝胶方法制备了具有NASICON结构的固体锂离子导体Li_1.3Al_0.3Ti_1.7(PO₄)₃,并且通过热重/差热分析、X射线衍射分析、比表面观测、电化学阻抗谱以及计时电流法等对其各方面性能进行了表征. 通过使用1,2-丙二醇辅助方法,未额外添加络合剂,也未对pH值进行调整得到均匀的溶胶前驱体,并且通过在850～950oC不同高温段烧结得到无杂相的具有NASICON结构     

一维Ni0.5Zn0.5Fe2O4/SiO2复合纳米结构的制备及其磁性能

采用溶胶-凝胶法结合静电纺丝技术制备了Ni_0.5Zn_0.5Fe₂O₄/SiO₂复合纳米纤维.利用热重-差热分析、X射线衍射、场发射扫描电镜、高分辨透射电镜和振动样品磁强计研究了前驱体纤维的热分解及相转化过程以及焙烧温度和SiO₂含量对目标纳米纤维的相组成、微观结构、形貌及磁性能的影响.结果表明,在450 ℃焙烧时,立方尖晶石结构已基本形成.随着焙烧温度由450 ℃升高到100     

Gd2O3:Eu3+纳米晶的燃烧合成及光致发光性质

采用柠檬酸作燃烧剂用燃烧合成法制备了Gd₂O₃:Eu³⁺纳米晶.用X射线衍射仪(XRD)、高分辨透射电子显微镜(HRTEM)和荧光分光光度计等对Gd₂O₃:Eu³⁺纳米晶的结构、形貌和发光性能进行了分析.结果表明：不同柠檬酸与稀土离子配比(C/M)制备的样品经800℃ 退火1 h后，均得到了纯立方相的Gd₂O₃:Eu³⁺纳米晶，晶粒尺寸约为30 nm，尺寸分布较窄，其中以C/M=1.0时制备的纳米晶结晶性最好，发光强度最大.Gd₂O₃:Eu³⁺纳米晶主发射峰位置均在612 nm处 (⁵D₀→⁷F₂跃迁)，激发光谱中电荷迁移态发生红移，观察到Gd³⁺向Eu³⁺的有效能量传递.对柠檬酸与稀土离子配比(C/M)对结晶度、发光性质等的影响也进行了分析和讨论.     

压力对纳米CoFe2O4/SiO2复合材料结构的影响

 采用溶胶-凝胶工艺和高温高压实验技术,制备了纳米CoFe₂O₄/SiO₂复合材料。利用X射线衍射仪、扫描电子显微镜和振动样品磁强计,对样品的结构、微观形貌和磁性进行了研究,并对CoFe₂O₄中阳离子的占位情况进行了讨论。结果表明,随着处理压力的升高,样品的晶粒尺寸增大,晶格常数减小,比饱和磁化强度增大。通过计算结果可以推断,压力的升高导致CoFe₂O₄中的部分Fe³⁺从A位移向了B位,而部分Co²⁺则从B位移向了A位。     

Er3+及Er3+/Yb3+掺杂ZrO2-Al2O3的制备及发光性质

采用共沉淀法制备了纳米晶ZrO₂-Al₂O₃∶Er³⁺发光粉体.所制备的粉体室温下具有Er3+离子特征荧光发射,主发射在绿光,其中位于547 nm、560 nm的绿光最强,并得出稀土离子与基质之间有能量传递.对不同煅烧温度下的样品研究表明:因不同温度下所制得的样品晶相不同.研究了纳米晶ZrO2-Al2O3∶Er3+及ZrO₂-Al₂O₃∶Er³⁺/Yb³⁺的上转换发光,并分析了上转换的跃迁机制.发现ZrO₂-Al₂O₃∶Er³⁺的绿光为双光子过程,而ZrO₂-Al₂O₃∶Er³⁺、Yb³⁺的上转换光谱中,红光和绿光也为双光子过程,而极弱的蓝光为三光子过程.讨论了Er³⁺的浓度猝灭现象.最适宜掺杂浓度的原子分数为2%（Er³⁺/Zr⁴⁺）.     

Cu(L-His)2溶液配位结构的X射线吸收精细结构分析

采用X射线吸收精细结构分析(XAFS)方法分析Cu(His)₂复合物的配位模式,通过测定不同pH值下的铜的K边XAFS吸收谱,研究Cu(His)₂第一配位壳层的结构．为了更准确地验证Cu(His)₂配位结构,对组氨酸的羧基和咪唑分别进行了化学修饰．研究结果明确了在不同pH环境下组氨酸的羧基、氨基和咪唑的配位情况．对于争议最大的在生理pH值下组氨酸的配位方式,其结果更支持六配位模式,同时可能有少量的五配位模式配合物平衡存在.     

纳米晶ZrO2:Er3+-Yb3+的制备及其室温上转换发射

用化学共沉淀法制备了ZrO₂:Er³⁺-Yb³⁺纳米晶粉体，所制备的纳米晶粉体具有较强的室温上转换发射和红外发射.研究了样品的晶体结构和上转换发光性质随着Yb³⁺掺杂浓度和煅烧温度的变化关系.通过X射线衍射谱分析发现，经800℃煅烧2h后得到的ZrO₂:Er³⁺-Yb³⁺纳米晶是四方相和单斜相的混合结构，经950℃煅烧2h后得到的样品以单斜相为主，随着Y     

由纳米管和纳米颗粒构成的TiO2膜的制备与机理研究

采用聚苯乙烯小球修饰Ti片表面,并进行阳极氧化,制备出一种由纳米颗粒和纳米管构成的TiO₂膜．通过数值模拟,分析了氧化表面附近的局部电场分布对TiO₂膜形貌的影响．结果表明,覆盖物增强了局部电场,从而加快了O^2-与Ti的反应速率,有利于TiO₂的生长;与此同时,[TiF₆]^6-的扩散受到阻碍,使得TiO₂的溶解速率减慢．可见,覆盖物打破了TiO₂纳米管形成的平衡条件,导致纳米颗粒的生成．此外,通过X射线衍射和Raman光谱的测试分析发现,所制备的TiO₂为锐钛矿结构.     

不同晶相结构和形貌TiO2负载Ru催化剂的CO选择甲烷化

用水热法得到的钛酸纳米纤维前体,通过不同后处理方法合成了多种纳米结构的TiO₂．采用N₂等温吸附和BET比表面、X射线衍射、透射电镜和能量分散X射线分析表征了TiO₂及负载Ru催化剂的微结构,包括比表面、晶相结构和形貌以及Ru纳米颗粒尺寸分布等．对负载Ru催化剂在富氢条件下CO选择甲烷化反应活性测试表明：金红石相TiO₂和TiO₂-B为载体负载的Ru催化剂比锐钛矿相TiO₂负载的Ru催化剂表现出更高的反应性能．其活性区别说明了不同晶相结构和形貌TiO₂载体与Ru纳米颗粒的相互作用存在差异．     

水热法制备不同形貌和结构的BiVO4粉末

采用水热合成法,选择不同比例的起始原料、反应温度、反应时间、pH值和表面活性剂,制备出不同形貌和结构的BiVO₄粉末.采用X射线衍射、透射电子显微镜、扫描电子显微镜、拉曼、傅里叶红外和紫外-可见吸收光谱技术对产物进行分析表征.结果表明,提高n_Bi/n_V或反应液pH值,可得到纯的单斜晶系白钨矿型BiVO₄粉末;水热温度和水热时间的不同则得到不同尺寸和内部结构的BiVO₄粉末.另外,不同表面活性剂的加入则主要影响BiVO₄的微观形貌. 关键词： 4')" href="#">BiVO₄ 水热法 光催化     

网状钼酸铋的可见光催化活性

采用无助剂、无模板的水热法成功合成网状Bi₂MoO₆. pH值对这一形貌的形成起重要作用. 所制备的网状Bi₂MoO₆样品表现出优异的可见光催化活性,其光催化活性比固相法合成的块状Bi₂MoO₆样品高得多.     

Flowerlike PtCl4/Bi2WO6 composite photocatalyst with enhanced visible-light-induced photocatalytic activity

Flowerlike PtCl₄/Bi₂WO₆ composite photocatalyst was successfully synthesized through a simple two-step method involving a template-free hydrothermal process and the following impregnation treatment. The samples were fully characterized by the study of X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis absorption spectra. The results indicated that the doping of Pt species did not affect the crystal structure and the morphology of Bi₂WO₆ photocatalyst, but it had great influences on the photocatalytic activity of Bi₂WO₆ towards rhodamine-B (RhB) degradation. Besides, the Pt species was found to be present as PtCl₄ in the composite samples, and also an optimal Pt species content on the surface of Bi₂WO₆ photocatalyst was discovered with the highest photocatalytic ability. The improved photocatalytic performance could be ascribed to the enhanced interfacial charge transfer and the inhibited recombination of electron-hole pairs. Meanwhile, a possible mechanism for RhB photocatalytic degradation over PtCl₄/Bi₂WO₆ catalyst was also proposed.     

Synthesis and characterization of Ag/BiVO4 composite photocatalyst

Ag/BiVO₄ composite photocatalysts were hydrothermal synthesized and characterized by XRD, SEM, XPS and DRS techniques. Their photocatalytic activities were determined by oxidative decomposition of methyl orange in aqueous solution under visible light irradiation. It revealed that the doped Ag species greatly improved the visible light absorption abilities and morphologies of the composites, and thus lead to enhanced photocatalytic activities compared with that of the pure BiVO₄.     

Synthesis and characteristics of natural zeolite supported Fe-TiO2 photocatalysts

Natural zeolite supported Fe³⁺-TiO₂ photocatalysts were synthesized for the sake of improving the recovery and photocatalytic efficiency of TiO₂. The as-prepared materials were characterized by X-ray diffraction (XRD), fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), ultraviolet-visible diffuse reflection spectroscopy (UV-vis DRS), scanning electron microscopy (SEM) and energy-dispersive X-ray analysis (EDX). Methyl orange was used to estimate the photocatalytic activity of the samples. The results showed that zeolite inhibited the growth of TiO₂ crystallite sizes. The Fe³⁺ concentration played an important role on the microstructure and photocatalytic activity of the samples. The iron ions could diffuse into TiO₂ lattice to the form Fe-O-Ti bond and gave TiO₂ the capacity to absorb light at lower energy levels. The photocatalytic activity of the samples could be enhanced as appropriate dosages of Fe³⁺ were doped.     

从可溶性单源分子前驱体采用溶胶凝胶法制备ZnO/TiO2 纳米复合物

合成了单源分子前驱体Cl₂TiZn(dmae)₄ (dmae为2-二甲基乙醇胺),并以乙醇为溶剂,加入等摩尔量的水对其进行可控水解得ZnO/TiO₂纳米复合凝胶,经pH=9沉淀,在200、400和600 oC 烧结得到不同的产物T₂₀₀、T₄₀₀、T₆₀₀. XRD分析表明未烧结产物为无定形粉末并随着烧结温度升高晶型改善. ZnO呈纤锌矿结构(六方晶系),TiO₂呈板钛矿型结构(正交). BET分析和扫描电镜表明颗粒的大小随着烧结温度的提高而增加. 红外光谱证明Zn-O和Ti-O的特有的振动频率,OH基团烧结后的产物中被去掉. 所有的样品都显示良好的光催化活性, 且T₆₀₀活性最高.     

Comparison of photocatalytic performance of anatase TiO2 prepared by low and high temperature route

Anatase TiO₂ was prepared by a facile sol-gel method at low temperature through tailoring the pH of sol-gel without calcination. As a control, anatase TiO₂ was also synthesized by the conventional sol-gel process, in which calcination at 500 °C was required to transform the amorphous oxide into highly crystalline anatase. As-prepared samples were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL). Their photocatalytic activities were evaluated by degradation of methyl orange under UV light irradiation. On the basis of experiment results, it could be concluded that TiO₂ prepared by low temperature route showed more advantages in small particle size, highly dispersion nature, abundance of surface hydroxyl groups, strong PL signal, and high photocatalytic activity over TiO₂ obtained by the conventional sol-gel process. Furthermore, the reason of the former possessing higher photocatalytic activity was discussed.     

Preparation, structure and photo-catalytic performances of hybrid Bi2SiO5 modified Si nanowire arrays

Bi₂SiO₅ modified Si nanowire array films were fabricated as photo-catalysts via dip-coating Bi(NO₃)₃ on silver-assisted electroless wet chemical etching Si nanowires and subsequently annealing. The structures and morphologies of as-prepared samples are characterized by X-ray diffraction, Fourier transform infrared spectrum, scanning electron microscopy and transmission electron microscopy. The results of photocatalytic experiments indicated that the Bi₂SiO₅ modified Si nanowire arrays benefit the improvement for efficient electron-hole separation and photo-catalytic stability, thereby possessing superior photo-degradation performance. These hybrid nanowire arrays will be promising materials for photo-catalysts and degradation agents.     

铈和磷钨酸共掺杂纳米二氧化钛中空纤维的制备及其光催化活性

以棉花纤维为模板,以钛酸四正丁酯、硝酸铈铵和磷钨酸为原料采用模板法制备了一系列铈和磷钨酸共掺杂的、具有中空纤维结构的TiO₂光催化材料, 利用扫描电子显微镜、X射线衍射、BET和紫外-可见光谱等技术对其形貌、晶体结构及表面结构、光吸收特性等进行了表征. 以苯酚溶液的光催化降解为模型反应,考察了不同掺杂量的样品在紫外和可见光下的光催化性能. 结果表明,用模板法制备的TiO₂纤维材料具有中空结构,共掺杂的TiO₂纤维在紫外和可见光条件下较纯TiO₂纤维和单掺杂TiO₂纤维对苯酚溶液具有更好的光催化降解效果, 且铈和磷钨酸的掺杂量显著影响该纤维材料的催化性能;当铈掺杂量为0.3mol%和磷钨酸掺杂量为2mol%,在500 oC焙烧2 h所得中空纤维材料的催化性能最佳,4 h即可使苯酚溶液的降解率达98.5%;重复使用4次仍可使苯酚溶液的降解率保持在87%以上,且该催化剂材料易于离心分离去除.     

Hydroxyethyl cellulose-assisted hydrothermal synthesis of Bi2S3 urchin-like colonies

Orthorhombic Bi₂S₃ with different morphologies was successfully synthesized by the acid-catalyst hydrothermal reactions of bismuth nitrate (Bi(NO₃)₃) and thiourea (NH₂CSNH₂) solutions containing different amounts of hydroxyethyl cellulose (HEC). Phase, morphologies, and optical properties were characterized by X-ray diffraction, selected area electron diffraction, scanning and transmission electron microscopy, and ultraviolet-visible spectroscopy. The products, hydrothermally synthesized in the HEC-free, 0.25 g HEC-added, 0.5 g HEC-added and 1.00 g HEC-added solutions, were respectively proved to be orthorhombic Bi₂S₃ irregular nanorods, complete urchin-like colonies of regular nanorods, incomplete urchin-like colonies of regular nanorods, and highly crystalline regular nanorods growing along the [001] direction. Tauc band gaps of the orthorhombic Bi₂S₃ nanorods, synthesized in the HEC-free, 0.25 g HEC-added, and 1.00 g HEC-added solutions were determined to be 3.0, 1.75 and 1.8 eV, respectively. Formation mechanism of orthorhombic Bi₂S₃ nanorods, synthesized in the HEC-free and HEC-added solutions, was also discussed at great detail.