Ag/TiO2纳米材料的制备和光致变色性能研究

 采用光催化还原法在不同温度热处理的TiO2薄膜表面沉积Ag纳米颗粒,制备了Ag/TiO2纳米薄膜材料。通过UV-Vis吸收光谱表征对比了不同温度热处理的TiO2对Ag粒子光催化沉积的影响,发现500℃退火处理TiO2薄膜较利于Ag纳米粒子的光催化沉积;在650 nm红色激光照射下,500℃退火处理的Ag/TiO2样品具有明显的光致变色现象,对此变色过程中涉及的机理进行了讨论,且发现随着Ag纳米颗粒光催化沉积时间的增长,Ag/TiO2薄膜光致变色的响应速率提高,但Ag纳米颗粒过多会抑制Ag/TiO2薄膜的变色响应速率。     

Au/SiO2纳米多层薄膜的制备及其性质表征

利用多靶磁控溅射技术制备了Au/SiO₂纳米颗粒分散氧化物多层复合薄膜.研究了在保持Au单层颗粒膜沉积时间一定时薄膜厚度一定、变化SiO₂的沉积时间及SiO₂的沉积时间一定而改变薄膜厚度时，多层薄膜在薄膜厚度方向的微观结构对吸收光谱的影响.研究结果表明：具有纳米层状结构的Au/SiO₂多层薄膜在560 nm波长附近有明显的表面等离子共振吸收峰，吸收峰的强度随Au颗粒的浓度增加而增强，在Au颗粒浓度相同的情况下，复合薄膜 关键词： 2纳米复合薄膜')" href="#">Au/SiO₂纳米复合薄膜 多靶磁控溅射 吸收光谱 有效介质理论     

脉冲激光沉积Ag:BaTiO3纳米复合薄膜及其光学特性

在MgO(100)基片上利用脉冲激光沉积技术制备了掺有Ag纳米颗粒的BaTiO₃复合薄膜.通过X射线衍射对薄膜的结构进行了表征,利用透射电子显微镜对Ag纳米颗粒的尺寸、形态进行了观测,X射线光电子能谱结果表明Ag呈金属态.在410—500nm范围内观测到了Ag纳米颗粒引起的等离子振荡峰,随着后处理温度和Ag颗粒浓度的增加,吸收峰发生红移,并出现了双峰现象. 关键词： 金属纳米复合薄膜 激光沉积 光吸收     

脉冲激光沉积Ag:BaTiO3纳米复合薄膜及其光学特性

在MgO(100)基片上利用脉冲激光沉积技术制备了掺有Ag纳米颗粒的BaTiO3复合薄膜.通过X射线衍射对薄膜的结构进行了表征,利用透射电子显微镜对Ag纳米颗粒的尺寸、形态进行了观测,X射线光电子能谱结果表明Ag呈金属态.在410-500 nm范围内观测到了Ag纳米颗粒引起的等离子振荡峰,随着后处理温度和Ag颗粒浓度的增加,吸收峰发生红移,并出现了双峰现象.     

不同厚度溅射Ag膜的微结构及光学常数研究

用直流溅射法在室温Si基片上制备了4．9nm-189.0nm范围内不同厚度的Ag薄膜，并用X射线衍射及反射式椭偏光谱技术对薄膜的微结构和光学常数进行了测试分析。结构分析表明：制备的Ag膜均呈多晶状态，晶体结构仍为面心立方；随膜厚增加薄膜的平均晶粒心潮6．3nm逐渐增大到14．5nm；薄膜晶格常数均比标准值（0．40862nm)稍小，随膜厚增加，薄膜晶格常数由0．40585nm增大到0.40779nm。250nm-830nm光频范围椭偏光谱测量结果表明：与Johnson的厚Ag膜数据相比，我们制备的Ag薄膜光学折射率n总体上均增大，消光系数k变化复杂；在厚度为4．9nm-83.7nm范围内，实验薄膜的光学常数与Johnson数据差别很大，厚度小于33．3nm的实验薄膜k谱线中出现吸收峰，峰位由460nm红移至690nm处，且其对应的峰宽逐渐宽化；当膜厚达到约189nm时，实验薄膜与Johnson光学常数数据已基本趋于一致。     

光电变色器件用纳米晶氧化钛薄膜的微结构与特性

纳米晶TiO2薄膜在光电变色器件中具有很重要的作用。它的微结构直接影响染料的吸附、光的散射以及电荷输运的特性。因此，探索TiO2薄膜的微结构(如粒径、表面形貌和厚度等)及光电性能是非常有意义的。采用电子束蒸发工艺制备了光电变色器件用纳晶TiO2薄膜，利用原子力显微镜、X射线衍射、俄歇电子能谱等手段对纳米晶TiO2薄膜的表面形貌、结晶状态及组分进行了分析。从理论上研究和讨论了纳米晶TiO2薄膜晶粒尺寸对光电性能的影响，并用量子限制效应解释了吸收光谱峰值波长随粒径减小而发生蓝移的现象。     

Au/SiO2纳米多层薄膜的制备及其性质表征

利用多靶磁控溅射技术制备了Au/SiO2纳米颗粒分散氧化物多层复合薄膜.研究了在保持Au单层颗粒膜沉积时间一定时薄膜厚度一定、变化SiO2的沉积时间及SiO2的沉积时间一定而改变薄膜厚度时,多层薄膜在薄膜厚度方向的微观结构对吸收光谱的影响.研究结果表明:具有纳米层状结构的Au/SiO2多层薄膜在560nm波长附近有明显的表面等离子共振吸收峰,吸收峰的强度随Au颗粒的浓度增加而增强,在Au颗粒浓度相同的情况下,复合薄膜光学吸收强度随薄膜厚度的增加而增强.但当金属颗粒的浓度增加到一定程度时,金属颗粒相互接触,没有观察到纳米层状结构,薄膜不显示共振吸收峰特征.用修正后的M-G(Maxwell-Garnett)理论对吸收光谱进行了模拟,得到了与实验一致的结果.     

中空Ag纳米球壳的制备及性能表征

 以改性聚苯乙烯微球为模板,采用化学镀法在聚苯乙烯微球表面包覆一层银,在四氢呋喃溶液中将聚苯乙烯微球溶解,得到中空Ag纳米球壳。采用扫描电镜、透射电镜和X射线衍射仪对样品进行了表征及分析,并用紫外可见分光光度计研究了粒子的光学性质。实验结果表明：运用此法成功地制备出中空Ag纳米球壳的内径为250 nm,壁厚约为15 nm,并且成功地使纳米粒子的紫外吸收光谱由600 nm红移至900 nm左右,实现了在可见光至近红外光区调节Ag纳米结构的吸收峰。     

掺Ag纳米颗粒的BaTiO3复合薄膜的非线性光学特性

通过准分子激光(XeCl,308 nm,20 ns)在MgO(100)单晶衬底上制备了不同掺杂浓度的Ag:BaTiO3纳米复合薄膜,通过X射线衍射和X射线光电子能谱对薄膜的结构和组分进行了表征.在430 nm和470 nm附近观测到了不同浓度Ag纳米颗粒引起的等离子体吸收峰,通过z扫描技术对复合薄膜的三阶非线性光学特性进行了测量,并对其光学非线性的增强机制进行了讨论.     

氢对GaAs薄膜的钝化作用

报导了射频磁控溅射与沉积气氛掺氢相结合制备单层(13~20 nm厚)高质量GaAs多晶态纳米薄膜的方法,研究了氢钝化对薄膜微观结构及光学性质的影响.对GaAs薄膜进行了X射线衍射、原子力显微镜、吸收光谱、光致荧光谱的研究分析.结果表明,衬底温度500℃的掺氢薄膜和520℃的薄膜呈面心立方闪锌矿结构，薄膜的晶团尺寸较大，微观表面较为粗糙，其吸收光谱出现了吸收边蓝移和明显的激子峰，带隙光致荧光峰强明显增加，说明氢在衬底温度500℃~520℃下对薄膜有重要的钝化作用.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.