四角锥氧化锌的制备及其强蓝光发射性质研究

采用热蒸发锌(Zn)粉的方法制备了大量的ZnO纳米棒状和四角锥状结构。用扫描电子显微镜(SEM)、拉曼光谱(Raman Spectra)和光致发光谱(PL)对样品进行了形貌,结构和发光特性分析。结果表明:合成的ZnO纳米棒具有良好的晶体结构,直径约100～500 nm,长度约2～5μm,还有一些四角锥状结构。在325 nm波长光激发下,有微弱的391 nm带边紫外发射和很强的488 nm蓝光发射,呈现出纳米ZnO优异的蓝光特性,并对其生长机理和发光机理进行了初步的探讨。     

高分子网络凝胶法制备ZnO超细粉体及其光学性能

采用高分子网络凝胶法制备球形ZnO超细粉体。通过聚乙烯醇(PVA)亚浓溶液交联网络的空间位阻作用,经过烧结,获得了具有球形形貌的粒径为1~3μm的ZnO粉体颗粒。利用X射线衍射(XRD)、扫描电镜(SEM)分析了不同PVA浓度以及退火温度对产物形貌、结构的影响,发现在PVA溶液浓度为5%,并且经500℃热处理所形成的ZnO球形颗粒最为均匀规整。研究了球形ZnO粉体的光致发光性能,室温下经325nm波长激发,观察到两个中心波长分别位于407,468nm的微弱的荧光发射带,在合适温度下,在385nm处还出现了较强的紫外峰。PL光谱表明,退火温度对ZnO的光致发光影响较大,随着退火温度升高,由于表面缺陷和结晶性能发生变化,407nm处发射峰逐渐减弱消失,而紫外发光先增强后减弱,经500℃热处理样品的紫外发光性能达到最佳。     

MO-Y2O3-B2O3:Re(M=Mg,Sr;Re=Eu,Tb)的真空紫外光谱特性

采用高温固相反应法合成了掺杂Eu3 及Tb3 的17MO-7.88Y2O3-75B2O3样品,研究了它们的光谱特性,结果表明,MO-T2O3-B2O3基质在真空紫外(VUV)区有很强的吸收,MgO-Y2O3-B2O3:Eu在147nm真空紫外光激发下产生对应于Eu3 的5D0→7FJ(J=1,2,3,4)跃迁的590和613 nm强发射峰;MgO-Y2O3-B2O3:Eu中Sr的引入使材料体系在147 nm附近的吸收和在613 nm附近的发射获得明显增强;MgO-Y2O3-B2O3:Tb的真空紫外激发谱除在147 nm附近的基质吸收外,还有对应于Tb3 的4f75d→4f8跃迁位于170,178,195,204,225 nm左右的一组谱峰,两者相互叠加使得材料在真空紫外区(120～220 nm)内都有很好的吸收.     

真空紫外-紫外光激发下的Na_2SO_4:TbF_3的发光性质

在空气中900℃温度下,对纯天然无水芒硝(Na2SO4)和TbF3的混合粉末加热20min,制备了Na2SO4:TbF3发光材料。并测量了在室温中真空紫外-紫外光下的发射和激发光谱。发射光谱有一系列由于Tb3+离子的5D4→7FJ(J=6,5,4,3,2)和5D3→7FJ(J=6,5,4,3,2)跃迁发射峰。通过监测542nm处发光得到的激发光谱,分别由Tb3+离子4fn→4fn-15d跃迁(187,193,218nm),基质吸收(165,200,240nm)引起的强激发谱和禁戒的f-f跃迁产生的弱激发谱组成。在TbF3的掺杂量在0.3%～2%范围内,随着Tb3+离子掺杂量的增加,真空紫外区的激发谱相应地逐渐增强。     

CVD两步法生长ZnO薄膜及其光致发光特性

用CVD两步法在常压下于p型Si(100)衬底上沉积出具有较好择优取向的多晶ZnO薄膜。在325nm波长的光激发下,室温下可观察到显著的紫外光发射(峰值波长381nm)。高温退火后氧空位缺陷浓度增加,出现了一个450~600nm的绿光发光带,发光峰值在510nm。作为比较,用一步法生长的ZnO薄膜结晶质量稍差。在其PL谱中不仅有峰值波长389nm的紫外发射而且还出现了一个很强的蓝光发光中心(峰值波长437nm),退火后同样产生绿光发光带。对这两种绿光发光带的发光机制进行了研究,认为前者源于VO,而后者与O_Zn有密切的关系。     

(Y,G d)BO_3∶Tb~(3+)的真空紫外及紫外激发光谱特性

采用传统的高温固相反应法合成出(Y,Gd)BO3∶Tb荧光体,对所制得的荧光体进行了晶体结构分析,分析结果表明结晶良好。(Y,Gd)BO3∶Tb在147 nm真空紫外光激发下的发射主峰在544 nm(Tb3+的5D4→7F5跃迁),是一种绿色发光材料。样品的真空紫外激发光谱及紫外激发光谱表明,(Y,Gd)BO3∶Tb的基质吸收带位于150 nm附近。Gd3+离子对真空紫外区的光吸收有增强作用,存在着Gd3+→Tb3+的能量传递。测量了荧光粉在室温下的荧光衰减特性,其余辉时间约为8 m s,能够满足显示显像技术的要求。因此,(Y,Gd)-BO3∶Tb是一种有前景的PDP用绿色发光材料。     

BaZr(BO3)2:Eu的合成及发光性能研究

用硝酸盐热分解法成功制备了BaZr(BO3)2:Eu(Eu3+的掺杂量为摩尔分数5%)荧光材料,并研究了其在254及147 nm光束激发下的发光特性.254 nm光束激发下的发射主峰位于612 nm处,归属于Eu3+的5D0-7F2的电偶极跃迁,但在147 nm光束激发下的发射主峰位于592 nm处,归属于Eu3+的5D0-7F1的磁偶极跃迁.通过激发光谱分析,上述现象归因于在紫外激发下占据非对称格位Ba2+的Eu3+被优先激发,而在真空紫外激发下占据对称格位Zr4+的Eu3+被优先激发.结果表明BaZr(BO3)2:Eu并不适合作为等离子平板显示器用红色发光材料.     

CaAl_2Si_2O_8∶Eu,Ce,Tb单基三元掺杂荧光材料的制备及其光谱学特征研究

采用高温固相法制备了CaAl_2Si_2O_8∶Eu,Ce,Tb单基三元掺杂的荧光材料。使用X射线衍射仪(XRD)、拉曼光谱仪(Raman)和荧光分光光度计(PL)等测试手段对该荧光材料进行表征。采用XRD表征了样品的物相组成,测试结果表明稀土离子Eu~(2+)置换Ca~(2+)并没有引起CaAl_2Si_2O_8基质晶格结构的变化。拉曼光谱分析证实了样品中硅氧四面体和铝氧四面体的存在,表明了Eu~(2+)替代Ca~(2+)的数量与晶体形态畸变程度有关,Eu~(2+)进入基质晶格的数量影响着硅(铝)氧四面体的数量。PL测试结果表明样品在325nm光激发下,其发射峰主要表现为426nm(蓝光区)的强宽带发射峰和541nm(绿光区)的弱发射峰,其中426nm处的宽带发射峰可通过高斯拟合成三个位于393,419和474nm的拟合峰;对比分析荧光性能以及同等合成条件下样品荧光强度的不同,确定了该荧光材料在三掺Eu∶Ce∶Tb的摩尔比为1∶1∶1.5时所发射荧光最强。CIE色度图坐标显示三种掺杂比例下制备的荧光材料均发射蓝色荧光,光显色性好,色温低,是一种适合作为紫外-近紫外激发的LED用蓝色荧光材料。     

激光分子束外延方法生长的ZnO薄膜的发光特性

研究了不同温度和不同光激发强度下激光分子束外延方法生长的ZnO薄膜样品的发光性能,发现YAG脉冲激光激发,强度超过一定值时会在长波方向上出现一个新的发光峰,此峰可能起源于电子-空穴的复合。室温下氙灯激发的光谱中可以看到峰值位于381nm的近带边紫外发射峰和位于450nm的强的蓝绿带发射,根据光致发光激发光谱的特征给出了一个简单的蓝光发射模型。对比YAG脉冲激光激发和氙灯激发得到的实验光谱,我们认为不同的光谱特征和样品发光的激发机制有关,紫外峰发射需激发强度超过一定值才能观察到,而蓝带发射则在一定的激发强度下迅速饱和。     

近紫外荧光粉SrAl_2Si_2O_8∶Ce~(3+)的光致发光特性

采用高温固相反应法制备了xCe~(3+)(x=0.01%,0.05%,0.10%和0.30%)激活的Sr_(1-x)Al_2Si_2O_8近紫外荧光粉,利用X射线衍射(XRD)和扫描电镜(SEM)检测出荧光粉的物相结构,通过光致发光谱(PL)和激发光谱(PLE)表征了荧光粉的发光性质。结果显示,在中波紫外光激发下,发射峰位于长波紫外区,归属于Ce~(3+)的5d→2 F5/2和5d→2 F7/2跃迁。激发波长308nm时,观察到近紫外SrAl_2Si_2O_8荧光粉的发光强度随Ce~(3+)掺杂量增加而先增大后减小,同时发射峰位置红移。280和325nm波长选择性激发条件下的差异性发射行为表明SrAl_2Si_2O_8∶Ce~(3+)具有两种性质不同的发光中心,该结论由监测320和390nm发射时获得的形状具有明显区别的激发光谱亦可得以验证。离子半径的匹配性支持Ce~(3+)优先取代Sr~(2+),同时Van Uitert的经验公式估算结果推断出低浓度的Ce~(3+)生成九配位的Ce(Ⅰ)发光中心,高浓度掺杂情况下部分相互近邻的Ce~(3+)有效配位数减小,形成八配位的Ce(Ⅱ)发光中心。紫外280nm激发下峰位348nm的发射谱带源于Ce(Ⅰ)和Ce(Ⅱ)发光中心共同贡献,紫外325nm激发下发射峰位于378nm的发射带则主要对应于Ce(Ⅱ)发光中心。紫外光激发下Ce~(3+)发射出较强的近紫外光,表明SrAl_2Si_2O_8∶Ce~(3+)是一种适用于研发紫外荧光光源的荧光粉体材料。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.