抽运光角度调谐准相位匹配光学参量振荡器的研究

针对利用周期极化晶体实现的抽运光角度调谐准相位匹配(QPM)光学参量振荡器(OPO)进行了系统的理论分析，给出了描述QPM OPO中抽运光旋转角与三波波长关系的精确公式和近轴公式.研究发现，对信号光单谐振的情况而言，抽运光与空闲光沿晶体x轴的同侧出射，而对空闲光单谐振而言，抽运光与信号光沿晶体x轴的同侧出射.另外，信号光单谐振下信号光与空闲光间的夹角要大于空闲光单谐振下两者间的夹角.更重要的是，信号光单谐振时的波长调谐速度也较空闲光单谐振时的大. 关键词： 准相位匹配 空闲光单谐振光学参量振荡器 抽运光角度调谐 调谐速度     

Fiber-laser-pumped continuous-wave singly resonant optical parametric oscillator

We report on what is to our knowledge the first continuous-wave (cw) optical parametric oscillator (OPO) that is pumped by a tunable fiber laser. The OPO is singly resonant for the signal wave and consists of a 40-mm-long periodically poled LiNbO(3) crystal in a four-mirror ring cavity. At a pump power of 8.3 W provided by the wavelength-tunable Yb-doped fiber laser, the singly resonant OPO generates 1.9 W of 3200-nm cw idler radiation. The singly resonant OPO was tuned from 1515 to 1633 nm (signal) and from 3057 to 3574 nm (idler) by means of the crystal temperature and poling period. We obtained a wide idler tuning range, from 2980 to 3700 mn, by tuning the wavelength of the fiber laser from 1032 to 1095 nm.     

Rapidly tunable continuous-wave optical parametric oscillator pumped by a fiber laser

We report on rapid, all-electronically controlled wavelength tuning of a continuous-wave (cw) optical parametric oscillator (OPO) pumped by an ytterbium fiber laser. The OPO is singly resonant for the signal wave and consists of a 40-mm-long periodically poled lithium niobate crystal in a four-mirror ring cavity. By tuning of the fiber-laser wavelength over 33 nm through an intracavity acousto-optic tunable filter, the OPO idler wavelength is tuned from 3160 to 3500 nm in 330 micros, corresponding to an idler frequency-tuning speed of 28 THz/ms. At a fiber-laser power of 6.6 W at 1074 nm, the singly resonant OPO generates 1.13-W cw idler radiation at 3200 nm.     

Wide wavelength tuning of an optical parametric oscillator through electro-optic shaping of the gain spectrum

We present a novel technique for tuning an optical parametric oscillator (OPO) through electro-optically induced shape variations of the parametric gain spectrum in quasi-phase-matched lithium niobate (LN). The diode-pumped, triply resonant continuous-wave OPO is based on a 58-mm-long LN crystal that consists of three equally long sections, the outer sections being periodically poled with a 50% duty cycle. The center section is single-domain material and serves as a tunable phase shifter through the electro-optic effect. By application of a voltage of up to 1230 V, the OPO signal and idler wavelengths are tuned over 102 nm from 1560 to 1660 nm, in good agreement with theory.     

High-average-power mid-infrared ZnGeP2 optical parametric oscillator with a wavelength-dependent polarization rotator

A wavelength-dependent polarization rotator is used to transform the orthogonal polarizations of the signal and idler of a near-degenerate type II KTP optical parametric oscillator (OPO) into a common polarization state. This common polarization allows a single ZnGeP2 OPO to fully utilize the 2 microm signal and idler KTP OPO outputs in a mid-IR conversion. The simple design of the wavelength-dependent polarization rotator yields a compact source that simultaneously generates four mid-JR wavelengths collinearly with a total mid-IR average power of 5.5 W at a >15 kHz pulse repetition rate.     

Thermal self-frequency locking of a doubly resonant optical parametric oscillator

The increase in the circulating signal and idler fields that occurs in a high- Q doubly resonant optical parametric oscillator (OPO) as it approaches resonance results in a small increase in the crystal temperature owing to absorption of the generated fields. The temperature change affects the refractive index of the crystal and alters the optical path length of the cavity. This effect may lead to self-frequency locking of the OPO to a specific resonance of the signal and idler fields, and it also results in peculiarities in the transient response of the system as it is scanned through resonance. We show that the experimentally observed effects are consistent with the results of a numerical model of the OPO.     

Tunable 7 12-microm optical parametric oscillator using a Cr,Er:YSGG laser to pump CdSe and ZnGeP(2) crystals

A CdSe optical parametric oscillator (OPO) pumped by a 2.79-mum , Cr, Er:YSGG laser yielded a 59% signal-plus-idler slope efficiency (eta), a total idler output of 1.2-2.4mJ between 8.5 and 12.3 mum , and an idler beam that was 2.2-2.5 times the diffraction limit. A ZnGeP(2) OPO operated with a lower threshold, eta = 29% , and a forward idler output of 0.7-2.4 mJ from 6.9 to 9.9 microm . The signal and idler bandwidths were typically 4 cm(-1) for each OPO.     

A 515-nm laser-pumped idler-resonant femtosecond BiB3O6 optical parametric oscillator

We report on an idler-resonant femtosecond optical parametrical oscillator(OPO)based on BiB₃O₆(BiBO)crystal,synchronously pumped by a frequency-doubled,mode-locked Yb:KGW laser at 515 nm.The idler wavelengths of OPO can be tuned from 1100 nm to 1540 nm.At a repetition rate of 75.5 MHz,the OPO generates as much as 400 mW of idler power with 3.1 W of pump power,the corresponding pulse duration is 80 fs,which is 1.04 times of Fourier transform-limited(FTL)pulse duration at 1305 nm.In addition,the OPO exhibits excellent beam quality with M²<1.8 at 1150 nm.To the best of our knowledge,this is the first idler-resonant femtosecond OPO pumped by 515 nm.     

Application of a continuously tunable, cw optical parametric oscillator for high-resolution spectroscopy

We report the use of a smoothly tunable, single-frequency continuous-wave optical parametric oscillator (OPO) for high-resolution spectroscopy. The OPO is based on potassium titanyl phosphate and is resonant for both signal and idler fields, resulting in a device with a very low pump power threshold of 30 mW. The frequency-selective nature of the doubly resonant oscillator ensures that the signal and idler modes can be tuned across the entire phase-match bandwidth without the need for additional intracavity frequency-selective components. Smooth frequency tuning of the output of the OPO is obtained by tuning of the pump laser. To demonstrate the practicality of our OPO we recorded the absorption spectrum of cesium vapor in the 1-microm spectral region.     

2.5-GHz repetition-rate singly resonant optical parametric oscillator synchronously pumped by a mode-locked diode oscillator amplifier system

We report on an optical parametric oscillator (OPO) that is synchronously pumped directly by a diode laser. This laser is an actively mode-locked master-oscillator power-amplifier system that produces 20-ps pulses at 927 nm with a repetition rate of 2.5 GHz and an average power of 0.9 W. The OPO, which is a singly resonant device based on periodically poled lithium niobate, generates 7.8-ps pulses. The OPO threshold is 300 mW of average pump power, and the maximum average idler output power is 78 mW at a wavelength of 2100 nm. By changing the crystal temperature we can wavelength tune the output in the ranges 1530-1737 nm (signal) and 1986-2348 nm (idler). Rapid wavelength tuning of the OPO over 46 nm (signal) and 74 nm (idler) is achieved through tuning the cavity length over 28 microm by use of a piezoelectric transducer.     

Dominant effect of polariton-polariton interactions on the coherence of the microcavity optical parametric oscillator

The importance of interaction effects in determining the temporal coherence of spectrally and spatially isolated single modes of the microcavity optical parametric oscillator (OPO) is demonstrated. As a function of macroscopic occupancy, the coherence time (tau c) first increases linearly and then exhibits saturation behavior, reaching maximum values of up to 500 ps. Good agreement is found with a model including fluctuations in polariton number and polariton-polariton interactions between the OPO states. tau c is a property of the coupled OPO system, a result confirmed by the finding of equal coherence times for signal and idler, even though the idler is subject to strong additional scattering.     

Dual-wavelength, two-crystal, continuous-wave optical parametric oscillator

We report a cw optical parametric oscillator (OPO) in a novel architecture comprising two nonlinear crystals in a single cavity, providing two independently tunable pairs of signal and idler wavelengths. Based on a singly resonant oscillator design, the device permits access to arbitrary signal and idler wavelength combinations within the parametric gain bandwidth and reflectivity of the OPO cavity mirrors. Using two identical 30 mm long MgO:sPPLT crystals in a compact four-mirror ring resonator pumped at 532 nm, we generate two pairs of signal and idler wavelengths with arbitrary tuning across 850-1430 nm, and demonstrate a frequency separation in the resonant signal waves down to 0.55 THz. Moreover, near wavelength-matched condition, coherent energy coupling between the resonant signal waves, results in reduced operation threshold and increased output power. A total output power >2.8 W with peak-to-peak power stability of 16% over 2 h is obtained.     

Vortices in the microcavity optical parametric oscillator

A theoretical treatment is presented for a novel from of optical vortex state, in a microcavity optical parametric oscillator (OPO). The state comprises a vortex/anti-vortex pair in the signal and idler beams, with a Gaussian pump. A numerical solution of the microcavity OPO equations shows that such a vortex can be stable.     

Measurement of the optical phase relation among subharmonic pulses in a femtosecond optical parametric oscillator

We observed the phase relation among subharmonic pulses generated by a femtosecond optical parametric oscillator (OPO). The ratio of the optical frequencies of the idler, the signal, and the pump pulses was set to 1:2:3. Under these conditions the wavelengths of the second harmonic of the signal pulse and the sum frequency between the pump and the idler pulses are the same. The beat signal between these two pulses represents the phase relationship among the pump, the signal, and the idler. The beat frequency varied when the cavity length of the OPO was changed.     

High-power synchronously pumped AgGaS(2) optical parametric oscillator

Greater than 2 W of average power was generated in the infrared region by a AgGaS(2) optical parametric oscillator (OPO). A Q -switched mode-locked laser was used to pump the OPO synchronously. Tunability from 1.4 to 1.9mum and a maximum output power of 750 mW at 1.44mum were achieved with a standing-wave cavity. Redesigning the cavity into a ring configuration allowed the depleted pump, signal, and idler beams to be extracted efficiently through separate mirrors. This design generated signal and idler beams of high spatial quality at respective power levels of 1.5 and 620 mW at a pulse repetition rate of 2 kHz.     

Compact, high-pulse-energy, picosecond optical parametric oscillator

We report a high-energy optical parametric oscillator (OPO) synchronously pumped by a 7.19 MHz, Yb:fiber-amplified, picosecond, gain-switched laser diode. The 42-m-long ring cavity maintains a compact design through the use of an intracavity optical fiber. The periodically poled MgO-doped LiNbO(3) OPO provides output pulse energies as high as 0.49 μJ at 1.5 μm (signal) and 0.19 μJ at 3.6 μm (idler). Tunability from 1.5 to 1.7 μm and from 2.9 to 3.6 μm is demonstrated, and typical M(2) values of 1.5 × 1.3 and 2.8 × 1.9 are measured for the signal and idler, respectively, at high power.     

Microchip laser-pumped continuous-wave doubly resonant optical parametric oscillator

We report what we believe to be the first use of a multilongitudinal-mode frequency-doubled microchip laser to pump a doubly resonant optical parametric oscillator (OPO). This compact OPO is based on potassium titanyl phosphate (KTP) and operates with a low pump power threshold of 35 mW. The OPO output consists of a single pair of signal and idler modes even though it is pumped with a multilongitudinal-mode pump laser. We achieved smooth tuning (1.7 GHz) of the output frequencies by temperature tuning of the pump laser.     

Widely tunable optical parametric oscillator with electrical wavelength control

A LiNbO(3) optical parametric oscillator (OPO) pumped at 930nm shows a wide phase-matching curve. Each pulse produced by the OPO has a very broad natural linewidth, from 1480 to 1800 nm for the signal and from 1950 to 2550 nm for the idler. The emission wavelength is controlled thanks to an electrically tunable Fabry-Perot interferometer inserted into the OPO cavity. The signal wavelength is electrically tuned in the range 1450-1850nm without crystal rotation.     

Continuous-wave singly resonant optical parametric oscillator based on periodically poled RbTiOAsO(4)

We report a continuous-wave optical parametric oscillator (OPO) based on periodically poled RbTiOAsO(4) (PPRTA). The singly resonant OPO, which is located within a Ti:sapphire laser, has a high-finesse signal cavity and delivers a maximum output power of 270 mW to the nonresonant idler wave at 2.92mum , through a 4.5-mm PPRTA crystal. For room-temperature operation and a crystal with a 30-mu;m grating period, pump tuning over 838-848 nm results in OPO tuning over 1.13-1.27mum (signal) and 2.53-3.26mum (idler), limited by the bandwidth of optical coatings. PPRTA exhibits thermal properties superior to those of periodically poled LiNbO(3) .     

Broadly tunable mid-infrared femtosecond optical parametric oscillator using all-solid-state-pumped periodically poled lithium niobate

We describe a high-repetition-rate femtosecond optical parametric oscillator (OPO) that was broadly tunable in the mid infrared. The all-solid-state-pumped OPO was based on quasi-phase matching in periodically poled lithium niobate. The idler was tunable from approximately 1.7 mum to beyond 5.4 mum, with maximum average power levels greater than 200 mW and more than 20 mW of average power at 5.4 mum. We used interferometric autocorrelation to characterize the mid-infrared idler pulses, which typically had durations of 125 fs. This OPO had a pumping threshold as low as 65 mW of average pump power, a maximum conversion efficiency of >35% into the near-infrared signal, a slope efficiency for the signal of approximately 60%, and a maximum pump depletion of more than 85%.