低阈值温度调谐PPMgLN红外光参量振荡

研究了温度调谐下周期极化镁掺杂铌酸锂晶体的红外光参量振荡特性。采用外电场短脉冲极化技术,在大小为7.0mm×50.0mm×1.0mm的Z切高镁掺杂(摩尔分数0.05)铌酸锂上制备出了准相位匹配光学微结构器件,极化周期为30.0μm。以输出波长为1064nm的声光调QNd:YAG固体激光器作为基频泵浦光开展了光参量振荡研究。实验表明:泵浦该PPMgLN晶体,实现了室温下低阈值红外光参量振荡产生,阈值功率仅为45mW(重复频率1kHz)。在泵浦输入功率为225mW时,有36mW信号光输出,转换效率达到16.0%,通过调谐晶体温度(20~180℃),获得了调谐范围为1503~1550nm波段的OPO信号光,实现了低阈值可调谐红外光的稳定输出。     

Rapidly tunable continuous-wave optical parametric oscillator pumped by a fiber laser

We report on rapid, all-electronically controlled wavelength tuning of a continuous-wave (cw) optical parametric oscillator (OPO) pumped by an ytterbium fiber laser. The OPO is singly resonant for the signal wave and consists of a 40-mm-long periodically poled lithium niobate crystal in a four-mirror ring cavity. By tuning of the fiber-laser wavelength over 33 nm through an intracavity acousto-optic tunable filter, the OPO idler wavelength is tuned from 3160 to 3500 nm in 330 micros, corresponding to an idler frequency-tuning speed of 28 THz/ms. At a fiber-laser power of 6.6 W at 1074 nm, the singly resonant OPO generates 1.13-W cw idler radiation at 3200 nm.     

2.5-GHz repetition-rate singly resonant optical parametric oscillator synchronously pumped by a mode-locked diode oscillator amplifier system

We report on an optical parametric oscillator (OPO) that is synchronously pumped directly by a diode laser. This laser is an actively mode-locked master-oscillator power-amplifier system that produces 20-ps pulses at 927 nm with a repetition rate of 2.5 GHz and an average power of 0.9 W. The OPO, which is a singly resonant device based on periodically poled lithium niobate, generates 7.8-ps pulses. The OPO threshold is 300 mW of average pump power, and the maximum average idler output power is 78 mW at a wavelength of 2100 nm. By changing the crystal temperature we can wavelength tune the output in the ranges 1530-1737 nm (signal) and 1986-2348 nm (idler). Rapid wavelength tuning of the OPO over 46 nm (signal) and 74 nm (idler) is achieved through tuning the cavity length over 28 microm by use of a piezoelectric transducer.     

Femtosecond fiber-feedback optical parametric oscillator

We demonstrate what is to our knowledge the first synchronously pumped high-gain optical parametric oscillator (OPO) with feedback through a single-mode fiber. This device generates 2.3-2.7 W of signal power in 700-900-fs pulses tunable in a wavelength range from 1429 to 1473 nm. The necessary high gain was obtained from a periodically poled LiTaO(3) crystal pumped with as much as 8.2 W of power at 1030 nm from a passively mode-locked Yb:YAG laser with 600-fs pulse duration and a 35-MHz repetition rate. The fiber-feedback OPO setup is compact because most of the resonator feedback path consists of a standard telecom fiber. Because of the high parametric gain, the fiber-feedback OPO is highly insensitive to intracavity losses. For the same reason, the synchronization of the cavity with the pump laser is not critical, so active stabilization of the cavity length is not required.     

Continuous-wave pumped, all-fiber optical parametric oscillator assisted by stimulated Raman scattering

A continuous-wave pumped, all-fiber optical parametric oscillator (OPO) around 1523 nm based on the mixing interaction of parametric process and stimulated Raman scattering (SRS) effects are investigated in this paper. We study and give the detailed analysis of the generation and output characteristics of all-fiber OPO with the influence of the SRS effects. Experimental results show that there exists the saturation output effect for this kind of OPO due to the coexistence of first order SRS effect, second order SRS and the optical parametric oscillation. The maximal output power of OPO is about 100 mW as the pump power reaches 1.4 W. Furthermore, a depolarized L-band super-continuum light source from 1570 nm to 1640 nm based on the combined interaction of parametric process and SRS effects can also be obtained.     

宽调谐高效率的BBO光参量振荡器

本文报道用354.7nm泵浦的单共振BBO脉冲光参量振荡器在413～661nm和2513～765nm波段内获得了可调谐的振荡输出,最高总能量转换效率达52％;文中还讨论了输出特性。     

Widely tunable optical parametric oscillator with electrical wavelength control

A LiNbO(3) optical parametric oscillator (OPO) pumped at 930nm shows a wide phase-matching curve. Each pulse produced by the OPO has a very broad natural linewidth, from 1480 to 1800 nm for the signal and from 1950 to 2550 nm for the idler. The emission wavelength is controlled thanks to an electrically tunable Fabry-Perot interferometer inserted into the OPO cavity. The signal wavelength is electrically tuned in the range 1450-1850nm without crystal rotation.     

Narrowband tuning of an injection-seeded pulsed optical parametric oscillator based on a self-adaptive, phase-conjugate cavity mirror

Narrowband tuning of a pulsed optical parametric oscillator (OPO) is achieved with a self-adaptive injection-seeded optical cavity employing a phase-conjugate reflector. This approach is used in a novel OPO system based on periodically poled KTiOPO4 and pumped at 532 nm by a pulsed Nd:YAG laser. The OPO is injection seeded at 835-855 nm by a continuous-wave tunable diode laser, which also enables a Rh:BaTiO3 photorefractive crystal to act as a wavelength-selective phase-conjugate reflector, with no need for active control of cavity length. The single-longitudinal-mode tunability and operational simplicity of this OPO system are demonstrated experimentally.     

宽波段温度调谐MgO∶LiNbO3光学参量振荡器

采用电光调Q脉冲Nd∶YAG激光的二次谐波 (5 32nm)抽运温度调谐的MgO∶LiNbO3晶体光学参量振荡器 ,调谐范围达 80 0nm～ 175 0nm。在单谐振运转条件下 ,抽运阈值为 2 1.5mJ/ pulse ,最大抽运能量为 5 8mJ时输出为 6 .45mJ ,在大信号情况下的能量转换效率达 11% ,输出线宽 1nm左右。     

Continuous-wave singly resonant optical parametric oscillator based on periodically poled RbTiOAsO(4)

We report a continuous-wave optical parametric oscillator (OPO) based on periodically poled RbTiOAsO(4) (PPRTA). The singly resonant OPO, which is located within a Ti:sapphire laser, has a high-finesse signal cavity and delivers a maximum output power of 270 mW to the nonresonant idler wave at 2.92mum , through a 4.5-mm PPRTA crystal. For room-temperature operation and a crystal with a 30-mu;m grating period, pump tuning over 838-848 nm results in OPO tuning over 1.13-1.27mum (signal) and 2.53-3.26mum (idler), limited by the bandwidth of optical coatings. PPRTA exhibits thermal properties superior to those of periodically poled LiNbO(3) .     

Widely and continuously tunable optical parametric oscillator based on a cylindrical periodically poled KTiOPO(4) crystal

We report on what is to our knowledge the first realization of a quasi-phase-matched optical parametric oscillator (OPO) based on a crystal with a cylindrical shape. The main reason for interest in this device is its broad, continuous tuning. In experiments with a 1064-nm pump, the signal tuning range was equal to 525 nm (1515-2040 nm), and the corresponding idler was continuously tuned over 1340 nm (2220-3560 nm). The angular tuning was 26 degrees , with only a minor variation of the OPO threshold over the entire tuning range.     

可调谐钛宝石激光抽运的KTP单谐振光学参量振荡器的研究

介绍了 70 0nm～ 980nm的脉冲可调谐钛宝石激光抽运的KTP单谐振光学参量振荡器。通过改变抽运光波长作为光学参量振荡器输出参量光的调谐方式 ,确定了KTP晶体最佳切割角度 (θ=6 2 .5°,φ =0°) ,实验上获得了 12 5 1nm～ 2 5 32nm的连续参量光输出 ,最大输出能量约为 2 7 2mJ,最大转换效率为 35 7% (1311nm处 )。     

Distributed-feedback optical parametric oscillation by use of a photorefractive grating in periodically poled lithium niobate

We report a demonstration of distributed-feedback (DFB) optical parametric oscillation (OPO) by writing photorefractive gratings in periodically poled lithium niobate (PPLN). The photorefractive DFB structures were fabricated by illumination of PPLN with UV light through a photomask and by writing of PPLN with UV-light gated interfering laser beams at 532 nm. Evidence of OPO was observed from the spectral narrowing at the 1438.8- and the 619.3-nm signal wavelengths from 1064- and 532-nm-pumped PPLN crystals with the DFB grating periods phase matched to the 4084.5- and 3774-nm idler wavelengths, respectively.     

A Narrow Bandwidth BBO Optical Parametric Oscillator Injection－seeded by a Tunable Pulsed Ti：Sapphire Laser

Ａ　Ｎａｒｒｏｗ　Ｂａｎｄｗｉｄｔｈ　ＢＢＯ　Ｏｐｔｉｃａｌ　Ｐａｒａｍｅｔｒｉｃ　Ｏｓｃｉｌｌａｔｏｒ　Ｉｎｊｅｃｔｉｏｎ－ｓｅｅｄｅｄ　ｂｙ　ａ　Ｔｕｎａｂｌｅ　Ｐｕｌｓｅｄ　Ｔｉ：Ｓａｐｐｈｉｒｅ　ＬａｓｅｒＡＮａｒｒｏｗＢａｎｄｗｉｄｔｈＢＢ...     

Low-threshold, self-frequency-stabilized AgGaS(2) continuous-wave subharmonic optical parametric oscillator

We report the demonstration of a cw AgGaS(2) optical parametric oscillator (OPO). The subharmonic (3omega ? 2omega + omega) OPO is configured as a doubly resonant oscillator with weak pump enhancement. The temperature-tuned, noncritically phase-matched crystal is pumped by a diode laser at lambda(p) approximately 845 nm . Oscillation at lambda(s) approximately 1267 nm and lambda(i) approximately 2535 nm is observed at an input threshold power of 60 mW. Crystal thermal loading induces a robust passive self-frequency stabilization of any single-axial-mode pair to the OPO cavity resonance. The conversion efficiency is limited by thermal effects to 2% for a 200-mW pump input.     

30-fs, cavity-dumped optical parametric oscillator

We demonstrate cavity dumping of a synchronously pumped optical parametric oscillator (OPO). The OPO delivers 30-fs pulses with energies as high as 13 nJ at up to 400-kHz repetition rates. The OPO's tunability ranges from 570 to 600 nm and is limited by the resonator mirror coatings. The time jitter between pulses of a Ti:sapphire laser and the cavity-dumped OPO pulses is smaller than 30 fs, permitting multicolor time-resolved spectroscopic experiments.     

高亮度人眼安全KTP OPO激光器

采用多模NdYAG激光器泵浦非临界相位匹配的KTP-OPO,获得了光束角2.3 mrad、输出能量400 mJ、平均功率12 W、光-光转换效率40%的1 572 nm激光.泵浦源的参数为能量1 J、重复频率30 Hz.分析认为采用KTP OPO将NdYAG激光器的1 μm激光转换到人眼安全波段的方法是获得1.5 μm激光的最有效的手段之一;非临界相位匹配的KTP OPO的主要优点是大的接受角和无走离,因此即使多纵模激光泵浦情况下也可以获得很高的转换效率.     

Fiber-laser-pumped continuous-wave singly resonant optical parametric oscillator

We report on what is to our knowledge the first continuous-wave (cw) optical parametric oscillator (OPO) that is pumped by a tunable fiber laser. The OPO is singly resonant for the signal wave and consists of a 40-mm-long periodically poled LiNbO(3) crystal in a four-mirror ring cavity. At a pump power of 8.3 W provided by the wavelength-tunable Yb-doped fiber laser, the singly resonant OPO generates 1.9 W of 3200-nm cw idler radiation. The singly resonant OPO was tuned from 1515 to 1633 nm (signal) and from 3057 to 3574 nm (idler) by means of the crystal temperature and poling period. We obtained a wide idler tuning range, from 2980 to 3700 mn, by tuning the wavelength of the fiber laser from 1032 to 1095 nm.     

ZnGeP2 parametric oscillator pumped by a linewidth-narrowed parametric 2 microm source

A tandem optical parametric oscillator (OPO) is used to convert radiation from 1.064 microm to the mid-infrared. Spectral bandwidth narrowing close to 80 times compared with a conventional cavity was achieved by using a bulk Bragg grating as an outcoupler in a near-degenerate periodically poled KTiOPO(4) OPO. The narrowed 2,008 nm radiation was subsequently used for pumping the ZnGeP(2) OPO, which was tunable between 3.3 and 5.2 microm. Pulse energies of 170 microJ and pump depletion close to 70% were obtained in the ZnGeP(2) OPO. To our knowledge this is the first time the output from a near-degenerate type I PPKTP OPO has been used for ZnGeP(2) OPO pumping.     

Quasi-phase-matched generation of tunable blue light in a quasi-periodic structure

We present what is to our knowledge a new approach to generating tunable blue light by cascaded nonlinear frequency conversion in a single LiTaO3 crystal. Simultaneous quasi-phase matching of an optical parametric generation process and a sum-frequency mixing process is achieved by means of structuring the crystal with a quasi-periodic optical superlattice. The spectral (wavelength tuning and bandwidth) and power characteristics of the blue-light generation are studied with a fixed-wavelength 532-nm picosecond laser and a wavelength-tunable nanosecond optical parametric oscillator (OPO) as the pump sources. By tuning the OPO wavelength, we could tune the blue output over approximately 20 nm. Temperature tuning of the blue output at a fixed pump wavelength of 532 nm was limited to approximately 1.5 nm. A maximum blue power of 15 microW was generated at a pump power of 0.5 mW, corresponding to an efficiency of 3%.