Electrochemical properties of thin TiO2 electrode on Li1 + xAlxGe2 − x(PO4)3 solid electrolyte

A fabrication of all-solid-state thin-film rechargeable lithium ion batteries by sol-gel method is expected to achieve both the simplification and cost reduction for fabrication process. TiO₂ thin film electrode was prepared by PVP (polyvinylpyrrolidone) sol-gel method combined with spin-coating on Li_1 + xAl_xGe_2 − x(PO₄)₃ (LAGP) solid electrolyte which has wide electrochemical window. The thin film was composed of anatase TiO₂ that is the most active phase for Li insertion and extraction and contacted well with LAGP substrate. In the cyclic voltammogram, a redox couple was observed at 1.8 V vs. Li/Li⁺ assigned to Li insertion/extraction into/from anatase TiO₂, indicating that the thin film worked as electrode for lithium battery. The charge and discharge test in various charge and discharge rates revealed that the discharge process (delithiation) is thought to be faster than charge process (lithiation). It is attested that the sol-gel process, which derives both simplification and cost reduction for fabrication process, can be applied to thin film battery using LAGP solid electrolyte.     

Electrochemical behavior of nanostructured LiV3O8 in aqueous LiNO3 solution

Despite the large number of studies on the electrochemical behavior of LiV₃O₈ as a cathode material in nonaqueous lithium ion batteries, little information is available about the electrochemical behavior of LiV₃O₈ as an anode material in aqueous rechargeable lithium batteries. In this work, nanostructured LiV₃O₈ is successfully prepared using a low-temperature solid-state method. The electrochemical properties of the LiV₃O₈ electrode in 1 M, 5 M, and saturated LiNO₃ aqueous electrolytes have been characterized by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge/discharge experiments. The results show that LiV₃O₈ electrode in saturated LiNO₃ electrolyte exhibits good electrochemical performance in terms of specific capacity and electrochemical cycling performance. LiV₃O₈ electrode can be reversibly cycled in saturated LiNO₃ aqueous electrolyte for 300 cycles at a rate of 0.5 C (300 mA g⁻¹ is assumed to be 1 C rate) with impressive specific capacities.     

Effects of Al2O3 nanofiller and EC plasticizer on the ionic conductivity enhancement of solid PEO-LiCF3SO3 solid polymer electrolyte

A solid polymer electrolyte (SPE) is synthesized by solution casting technique. The SPE uses poly(ethylene oxide) PEO as a host matrix doped with lithium triflate (LiCF₃SO₃), ethylene carbonate (EC) as plasticizer and nano alumina (Al₂O₃) as filler. The polymer electrolytes are characterized by Impedance Spectroscopy (IS) to determine the composition of the additive which gives the highest conductivity for each system. At room temperature, the highest conductivity is obtained for the composition PEO-LiCF₃SO₃-EC-15%Al₂O₃ with a value of 5.07 10^− 4 S/cm. The ionic conductivity of the polymer electrolytes increases with temperature and obeys the Arrhenius law. X-ray diffraction (XRD) and differential scanning calorimetry (DSC) studies indicate that the conductivity increase is due to an increase in amorphous content which enhances the segmental flexibility of polymeric chains and the disordered structure of the electrolyte. Fourier transform infrared spectroscopy (FTIR) spectra show the occurrence of complexation and interaction among the components. Scanning electron microscopy (SEM) images show the changes morphology of solid polymer electrolyte.     

Unusual piezoresponse behavior across the grain boundary of PbMg1/3Nb2/3O3-0.33PbTiO3 thin films

Ferroelectric PbMg_1/3Nb_2/3O₃-0.33PbTiO₃ (PMN-0.33PT) polycrystalline thin film near MPB was grown on Ir with LaNiO₃ buffer layer by pulsed laser deposition technology. Piezoresponse force microscopy (PFM) was employed to investigate the role of grain boundary on the domains formation and their local physical properties in PMN-PT thin film. Unusual piezoresponse behaviors were firstly observed across the grain boundary of PMN-PT thin film via PFM. Such abnormal phenomenon is ascribed to the structural incompatibility-induced local stress across the grain boundary, which gives a deep influence on the local imprint behavior of PMN-PT thin film.     

Low-temperature performance of thin solid electrolyte cell based on MoO3-doped Bi2O3

Improvement of low-temperature performance of oxygen sensor was studied by preparing a thin film of 15 μm thickness. Melt-quenched Bi₂O₃ film doped with 16 mol% MoO₃ was used as an electrolyte after HF treatment. Impedance measurements were carried out in the frequency range DC-100 KHz. Resistance of electrolyte in the form of thin film (110ω) was negligibly small compared with the overall resistance of the cell (287 Kω) at 350°C. Oxygen/air concentration cell was constructed and the cell performance was measured at 350 and 300°C. Transference number close to unity and rapid response were observed at 350°C, however the cell showed a long response time of about 3 min at 300°C.     

Nanostructured Ni3Sn2 thin film as anodes for thin film rechargeable lithium batteries

Thin film Ni₃Sn₂ anodes were deposited on a Cu substrate by e-beam evaporator at room temperature. The deposited films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). They were tested as anodes for thin film rechargeable lithium batteries. These film electrodes exhibited an excellent cycle performance over 500 cycles. Ni₃Sn₂ films remained without undergoing any crystallographic phase change during cycling.     

Sn3InSb4合金嵌Li性能的第一性原理研究

采用第一性原理超软赝势平面波方法计算了Sn₃InSb₄的嵌Li性能,得到各种嵌Li相的嵌Li形成能、理论质量比容量、体积膨胀率、能带结构、态密度和差分电荷密度等.从能量角度分析,Li在嵌入时,优先占据晶胞的四面体间隙位置,然后逐步挤出处于节点位置的Sn原子和In原子.在嵌Li过程中,材料表现出较大的体积膨胀率(11.74%-43.40%),这是导致Sn₃InSb₄作为Li离子电极材料循环性能差的重要原因.态密度计算表明,体系的导电性能首先随嵌Li量的增加而增加,当所有的间隙位置被Li填满,发生Sn的替换反应时,富Li态合金相的导电性反而下降.     

Electrochromism in WO3 thin films. II. LiClO4-dioxolane-water electrolytes

The performances of electrochromic cells with evaporated amorphous WO₃ thin film as electrochromic material in (2.5 M) LiClO₄-dioxolane-water electrolytes are presented. A comparison with the results previously obtained in propylene carbonate instead of dioxolane solvent is carried out. The influence of the following parameters has been studied: the thickness of the film, the water content in the electrolyte, the potential applied to the electrochromic electrode during coloration and bleaching processes.     

In situ formation of Al2O3-SiO2-SnO2 composite ceramic coating by microarc oxidation on Al-20%Sn alloy

In situ formation of Al₂O₃-SiO₂-SnO₂ composite ceramic coating on Al-20%Sn alloy was successfully fabricated in aqueous Na₂SiO₃ electrolyte by microarc oxidation technology. The compositions, structure, mechanical and tribological properties of the composite coating were detailed studied by scanning electron microscope, energy dispersive spectroscopy, X-ray diffraction, hardness tester and ball-on-disc friction tester. It is found that the species originating from the Al-20%Sn alloy substrate and the electrolyte solution both participate in reaction and contribute to the composition of the coating, which results in the generated coating firmly adherent to the substrate. The composite ceramic coating can greatly improve the microhardness and tribological property of Al-20%Sn alloy.     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.     

Polyacrylonitrile electrolytes: 1. A novel high-conductivity composite polymer electrolyte based on PAN, LiClO4 and α-Al2O3

In this work, a series of novel solid-type α-Al₂O₃-containing polyacrylonitrile (PAN)-based composite polymer electrolytes (CPE) with high conductivity and high mechanical property at room temperature has been prepared. The effect of the addition of α-Al₂O₃ on the properties of the PAN-based composite polymer electrolyte has been analyzed. The best conductivities obtained at room temperature is 5.7×10⁻⁴ S cm⁻¹ from the CPE with 7.5 wt.% α-Al₂O₃ and 0.6 LiClO₄ per PAN repeat unit. The stress–strain test result indicates that the membranes prepared possess high yield stress (73 kg cm⁻²) suitable for serving as separators in the solid-state lithium and lithium ion batteries and high yield elongation (225%) pliable to form good interface with electrodes. Also discussed are the effects of the addition of the ceramics on the interactions in the system and the possible conduction mechanism.     

Electrochemical lithium incorporation into WO3 and MoO3 thin films

The generally accepted mechanism of electrochromic phenomena into WO₃ thin films involves the simultaneous injection of cations and electrons to form a tungsten bronze M_xWO₃, e.g. H_xWO₃,Li_xWO₃. Electrochromic cells of the type ITO MO₃/LiClO₄(M) in propylene carbonate/Pt, where M = W or MO and MO₃ is an amorphous thin film have been used. Different amounts of charges have been injected through these cells by electrochemical means at room temperature. The variations of the MO₃ electrode potential with the injected charge are in good agreement with the assumption of the formation of Li_xMO₃ compounds. The free enthalpies of formation of these bronzes have been calculated. The behavior of thin film electrodes seems to be intermediate between amorphous and crystallized bulky materials. Some measurements of electrode potential have also been carried out with crystallized thin films of sputtered WO₃.     

Synthesis of high tap density Li3V2(PO4)3 cathode materials using mixed lithium precursors

High tap density Li₃V₂(PO₄)₃ cathode materials were synthesized using mixed LiF and LiNO₃ as lithium precursors, LiNO₃ was used as the sintering agent. Rietveld refinement results show that no impurities phases are detected in products. Particle size distribution and tap density measurement results show that particle size and tap density of products can be increased by the addition of LiNO₃. Electrochemical characterization results show that electrochemical performance of products is declined with the increase in contents of LiNO₃ in the lithium precursors. Only a small amount of LiNO₃ added in the lithium precursors (mole ratio of LiNO₃ to LiF is 1:9) can increase the tap density and also retain the good performance of products. Scanning electron microscopy (SEM) images indicate that the samples prepared by mixed lithium precursors present particles agglomerate, and the particle size increased with increase in contents of LiNO₃. Large amount of LiNO₃ added in the lithium precursors induces the particles to become spheric and smooth, which worsens the performance. The particles obtained with the mole ratio of LiNO₃ to LiF in 1:9 show a flake-like shape with a high specific surface area, which leads to good electrochemical performance.     

Thickness dependence of magnetic domain formation in La0.6Sr0.4MnO3 epitaxial thin films studied by XMCD-PEEM

We have used photoelectron emission microscopy (PEEM) and X-ray magnetic circular dichroism (XMCD) to study the effect of thin film thickness on the magnetic domain formation in La_0.6Sr_0.4MnO₃ samples that were epitaxially grown on stepped SrTiO₃ (0 0 1) substrates. The magnetic image exhibited a stripe structure elongated along the step direction, irrespective of film thickness, suggesting that uniaxial magnetic anisotropy induced by step-and-terrace structures plays an important role in the magnetic domain formation. Additional domains evolved gradually with increasing film thickness. In these domains, the direction of magnetization differed from the step direction due to biaxial magneto-crystalline anisotropy. The evolution of additional magnetic domains with increasing film thickness implies that a competition exists between the two anisotropies in LSMO films.     

Direct observation of MoO2 crystal growth from amorphous MoO3 film

The formation process of MoO₂ crystal from amorphous MoO₃ film has been imaged by in situ observation with a transmission electron microscope. Selective growth of flower-shaped MoO₂ crystals by heating above 673 K in vacuum was directly observed. Since the MoO₂ crystal has metallic conductivity of the order of indium oxide film containing tin (ITO film), the thin film growth of the MoO₂ phase has been discussed on the basis of a new substitute for ITO film.     

Effect of Ce2(SO4)3 on structure and properties of Ni-Co/Al2O3 composite coating deposited by pulse reverse current method

Composite coating of Ni-Co/Al₂O₃ was deposited in Ce₂(SO₄)₃ containing electrolyte by pulse reverse current (PRC) method. The effect of Ce₂(SO₄)₃ in electrolyte on morphology, microstructure, composition, micro-hardness and residual macrostress of composite coating was investigated. The results indicates that with addition of Ce₂(SO₄)₃ in electrolyte, the composite coating becomes uniform, compact and possesses finer grains, the composite content of Al₂O₃ is enhanced, the micro-hardness of composite coating is improved, while the residual macrostress is decreased.     

Influence of Al2O3 additions on crystallization mechanism and conductivity of Li2O-Ge2O-P2O5 glass-ceramics

The crystallization mechanism and conductivity of lithium aluminum germanium phosphate [LAGP] glass-ceramics fabricated from Li_1+xAl_xGe_2−x(PO₄)₃ (x=0.0-0.7) glass system were investigated as a function of Al₂O₃ additions. A non-isothermal analysis was performed to study the crystallization behavior of LAGP glass-ceramics at various heating rates (5-25K min⁻¹) by the Kissinger equation and the Augis-Bennett equation, illustrating volume crystallization for the glass-ceramics. The crystal identification and microstructure in glass-ceramics containing various Al₂O₃ contents were analyzed by means of XRD and FESEM. The main phase of the glass-ceramics was found to be LiGe₂(PO₄)₃, with AlPO₄ as the impurity phase. Additionally the highest total ionic conductivity (5.8×10⁻⁴ S/cm) at room temperature was obtained when x=0.5 for Li_1+xAl_xGe_2−x(PO₄)₃ (x=0.0-0.7) glass-ceramics, suggesting that it was a promising electrolyte for practical application in all-solid-state lithium batteries.     

La0.8Ca0.2MnO3/SrTiO3薄膜厚度对其结构及磁学性能的影响

采用多种X射线衍射技术和磁电阻测量技术研究了不同厚度的La_0.8Ca_0.2MnO₃/SrTiO₃ (LCMO/STO)薄膜的应变状态及其对磁电阻性能的影响.结果表明，在STO(001)单晶衬底上生长的LCMO薄膜沿［00l］取向生长.LCMO薄膜具有伪立方钙钛矿结构，随着薄膜厚度的增加，面内晶格参数增加，垂直于面内的晶格参数减小,晶格参数a和b相近，略小于c.LC 关键词： X射线衍射 微结构 应变 物理性能     

外延PbZr0.4Ti0.6O3薄膜厚度对其铁电性能的影响

从Landau-Devonshire唯象理论出发，考虑到晶格失配导致的NFDA3位错应力场与极化场的耦合，研究了在SrTiO₃衬底上外延生长的PbZr_0.4Ti_0.6O₃薄膜厚度对其自发极化强度、电滞回线的影响. 结果表明，产生刃位错的PbZr_0.4Ti_0.6O₃薄膜临界厚度为～1.27nm，当薄膜厚度大于临界厚度时，在所形成的位错附近，极化强度出现急剧变化，形成自发极化强度明显减弱的“死层”；随着薄膜厚度的减小，位错间距增大，“死层”厚度与薄膜总厚度之比增加. 由薄膜电滞回线的变化情况可知，其剩余极化强度随着薄膜厚度的减小而逐渐减小. 关键词： 铁电薄膜 自发极化强度 电滞回线 位错     

La0.9Sr0.1MnO3薄膜中电流效应研究

用直流磁控溅射法在(100)LaAlO₃衬底上制备了La_0.9Sr_0.1MnO₃薄膜.经退火处理后薄膜的原子力显微镜形貌观测和X射线衍射分析显示具有比较好的质量.电阻率-温度关系表明La_0.9Sr_0.1MnO₃薄膜在281 K处发生金属绝缘体转变.电流在0.01—4 mA范围内，薄膜的峰值电阻率随电流增大而减小，在4 mA下获得了30.5%的峰值电阻率变 关键词： 掺杂锰氧化合物 0.9Sr_0.1MnO₃薄膜')" href="#">La_0.9Sr_0.1MnO₃薄膜 电流诱导效应 相分离理论