ZnO亚微米和微米棒的晶体生长及发光性质

用硝酸锌Zn(NO3 )2·4H2O和六亚甲基四胺 (CH2 )6N4,通过化学溶液法在玻璃衬底上生长出ZnO六角形亚微米和微米棒(长 5~6μm,直径 0. 8 ~5μm)。生长时间达两天后,ZnO棒呈中空六角形微米管。测量了样品的X射线衍射(XRD)谱,扫描电镜像和喇曼光谱。ZnO微米棒的光致发光为橙红色宽谱带发射(峰值 630nm, 半峰全宽 250nm), 其激发光谱除带间本征激发(短于 370nm)外,还有很强的在导带底附近的室温激子激发峰(峰值 387nm,半峰全宽 30nm)。而阴极射线发光有两个发射峰,橙色宽谱带强峰 (峰值580nm,半峰全宽约为140nm)是缺陷发光峰,近紫外窄谱带弱峰(峰值 395nm,半峰全宽约为 20nm)是激子发光峰。     

Sn掺杂ZnO纳米晶的水热法制备及光学性能

以ZnCl2和NaOH为原料,用SnCl4·4H2O作掺杂剂,通过水热法合成了Sn掺杂ZnO纳米颗粒。利用X射线衍射(XRD)、场发射扫描电镜(FE-SEM)、紫外-可见吸收光谱(UV-Vis)及光致发光(PL)光谱等测试技术对样品的物相、形貌及光学性能进行了表征。结果表明:制得的Sn掺杂ZnO纳米粒子具有六角纤锌矿结构。随着锡掺杂浓度的增大,纳米晶的平均粒度增加,晶体形貌由短棒状向单锥和双锥状转变;提高前驱液的pH值,所得样品的形貌由长柱状向短柱状转变。室温下,观测到三个光致发光带,一个峰值在433nm处的强紫光发射峰,一个约在401nm处的近紫外发光峰及一个在466nm处的弱蓝光发光峰。在实验掺杂浓度范围内,Sn的掺杂只是改变纳米ZnO的发光强度,对发光峰位置影响不大。     

蓝光ZnO薄膜的特性研究

采用反应溅射法在n型硅（100）衬底上制备了ZnO薄膜,分别用X射线衍射仪、原子力显微镜和荧光分光光度计对样品的结构、表面形貌和光致发光特性进行了表征。X射线衍射结果表明,实验中制备出了应变小的c轴择优取向的ZnO薄膜;原子力显微镜观察表明,薄膜表面平整,颗粒大小约为50nm,为柱状结构,颗粒垂直于硅衬底表面生长;在室温光致发光（PL）谱中观察到了波长位于434nm处的较窄的强蓝光发射峰,该蓝光峰的半峰全宽约为50meV。对蓝光峰的发光机制进行了讨论,并推断出该蓝光峰来源于电子从Zn填隙缺陷能级向价带顶跃迁。     

Na-Mg共掺杂ZnO薄膜的结构和光学性质

利用溶胶-凝胶法,在普通载玻片上使用旋转涂膜技术制备了具有c轴择优取向生长的Na-Mg共掺杂的ZnO薄膜。用XRD、SEM、光致发光(PL)及透射光谱对薄膜样品进行了表征。结果表明:Na-Mg共掺杂有利于ZnO薄膜的c轴择优取向生长,并且随着Na+掺杂浓度的增加,晶粒尺寸先增大后减小;通过比较不同掺杂浓度ZnO薄膜的PL谱,推测发光峰值位于380nm的紫外发射与ZnO的自由激子复合有关;发现掺入Mg的确能使ZnO禁带宽度增大,掺杂组分为Na0.04Mg0.2Zn0.76O时,其PL谱只有一个很强的紫光发射峰,其近带边紫外光发射强度较未掺杂的ZnO增强了近10倍,极大地提高了薄膜紫外发光性能;并且随Na+浓度增加薄膜透光性减弱。     

Fe掺杂ZnO纳米球的光学特性

采用微乳液法制备了Fe掺杂ZnO纳米球材料(Zn1-xFexO,x=0.1),利用XRD和TEM对制备样品的结构、形貌进行了表征。在室温下,测得材料宽化的吸收光谱。用325nm的激光激发,测量了ZnO纳米球的光致发光光谱,低强度激发时观察到半峰全宽较窄、峰值波长为385nm的紫光峰和半峰全宽较宽、峰值波长约625nm的深能级发光峰;两峰的发光强度和峰位随着激发光功率密度的变化而变化,但变化规律不同。所合成材料的吸收和发光性质与Fe掺杂相关。     

四角锥氧化锌的制备及其强蓝光发射性质研究

采用热蒸发锌(Zn)粉的方法制备了大量的ZnO纳米棒状和四角锥状结构。用扫描电子显微镜(SEM)、拉曼光谱(Raman Spectra)和光致发光谱(PL)对样品进行了形貌,结构和发光特性分析。结果表明:合成的ZnO纳米棒具有良好的晶体结构,直径约100～500 nm,长度约2～5μm,还有一些四角锥状结构。在325 nm波长光激发下,有微弱的391 nm带边紫外发射和很强的488 nm蓝光发射,呈现出纳米ZnO优异的蓝光特性,并对其生长机理和发光机理进行了初步的探讨。     

荧光体CaSO_4∶Eu的近紫外发光性质

CaSO4∶Eu是一种人们早已较为熟知的发光材料,由于其优异的热释发光特性而被广泛应用于辐射剂量学方面。近年来由于崭新的光致发光液晶显示模式的出现,人们又对其近紫外发射特性产生了极大兴趣。考察了CaSO4∶Eu的发光特性和材料的各种制备方法,以及制备条件对发光性能的影响,特别是对其近紫外发射性能的影响。实验表明,对于还原彻底、结晶良好的样品,激活剂Eu几乎全部以二价铕离子的形式存在,是一种很好的近紫外发射材料。该材料能被低压汞蒸气放电辐射有效激发,其发射带的峰值在386 nm附近,随Eu的掺杂浓度不同而略有差异,半峰全宽约为16 nm,基本满足了近紫外发射的要求,可应用于光致发光液晶显示器件的背照明光源中。     

弯曲表面上ZnO亚微米棒阵列的制备

以ZnS和金属Zn粉末混合物为蒸发源以及金属Zn片为衬底,利用热蒸发气相沉积方法,在弯曲的金属Zn微球表面上,成功地获得了ZnO亚微米棒阵列结构。场发射扫描电镜研究表明:在弯曲的Zn微球表面,能自组织地生长出大量的截面为六边形的ZnO亚微米棒,这些亚微米棒的平均直径为500nm,长约1μm。棒的顶部是平滑的。能量散射X射线谱结果表明:合成的产品只存在Zn和O两种元素,其成分比例接近1∶1。没有观察到S元素。光致发射(PL)光谱显示:在387nm紫外波长处,出现一个强的半峰全宽为16nm的窄发光峰,可归属于ZnO的近带边发光,而509nm左右较弱的宽峰则源于界面缺陷态发光。这些研究结果说明我们所合成的这种ZnO亚微米棒阵列材料在紫外受激发射器件方面有着潜在的应用价值。     

In掺杂的ZnO纳米棒的共振Raman光谱研究

本文报道In掺杂ZnO纳米棒的成功制备和对其结构以及光荧光性能的详尽研究。在室温条件下ZnO的共振拉曼谱线容易受到很强的荧光干扰, 甚至导致共振拉曼谱线完全被湮没。微量In掺杂入ZnO纳米棒中, 调控紫外发光峰由378 nm(纯ZnO)红移至397 nm; 另外, 在制备过程中引入过量的氧, 在样品中产生大量缺陷, 降低了ZnO的紫外近带边发光峰强度。这两方面导致在室温下可清楚的观察到In掺杂ZnO纳米棒的6阶LO拉曼峰。     

纳米ZnO薄膜可见发射机制研究

利用溶胶－凝胶法 （Sol-Gel）制备了纳米ZnO薄膜，获得了高强的近紫外发射室温下测量了样品的光致发光谱(PL )、吸收谱(ABS)、X射线衍射谱(XRD).X射线衍射(XRD)的结果表明：纳米ZnO薄膜呈多晶态，具有六角纤锌矿结构和良好的C轴取向；发现随退火温度升高，（002）衍射峰强度显著增强，衍射峰的半高宽（FWHM）减小、纳米颗粒的粒径增大.由吸收谱(ABS)给出了样品室温下带隙宽度为3.30 eV.在PL谱中观察到二个荧光发射带，一个是中心波长位于392 nm附近强而尖的紫带，另一个是519 nm附近弱而宽的绿带研究了不同退火温度样品的光致发光峰值强度的变化关系，发现随退火温度升高，紫带峰值强度增强、绿带峰值强度减弱，均近似呈线性变化.证实了纳米ZnO薄膜绿光发射主要来自氧空位(Vo)形成的浅施主能级与锌空位(VZn)形成的浅受主能级之间的复合，或氧空位(Vo)形成的深施主能级上的电子至价带顶的跃迁；紫带来自于导带中的电子与价带中的空位形成的激子复合.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.