PLD方法制备的ZnO纳米柱结构及光学特性

采用无催化脉冲激光沉积(PLD)方法,在InP(100)衬底上生长纳米ZnO柱状结构。采用扫描电子显微镜(SEM)、X射线衍射(XRD)以及光致发光(PL)谱等表征手段对ZnO纳米柱的形貌、晶体结构和光学特性进行了观察。SEM图像观察到ZnO纳米柱状结构具有一定的取向性;XRD测试在2θ=34.10°处观测到强的ZnO(002)衍射峰,证实ZnO纳米柱具有较好的c轴择优取向;室温PL谱在379nm处观察到了强的自由激子发射峰(半峰全宽为19nm),未探测到深能级跃迁发射峰,表明生长的纳米ZnO结构具有很高的光学质量。     

无催化法制备ZnO纳米针的结构及光学特性

采用无催化脉冲激光沉积(PLD)方法,在InP(100)衬底上生长纳米ZnO针状结构。采用扫描电子显微镜(SEM)、X射线衍射(XRD)以及光致发光(PL)谱等对ZnO纳米针的形貌、晶体结构和光学特性表征。SEM图像观察到ZnO纳米针状结构具有一定的取向性。XRD测试在2θ=34.50°处观测到强烈的ZnO(002)衍射峰,证实ZnO纳米针具有较好的c轴择优取向。室温PL谱在379nm处观察到了较强的自由激子发射峰(半峰全宽为13.5nm),而微弱的深能级跃迁峰位于484nm,二者峰强比值为11∶1,表明生长的纳米ZnO结构具有较高的光学质量。     

直立Zn_2GeO_4/ZnO纳米棒阵列的制备及其发光性质研究

利用化学气相沉积法(CVD)在表面溅射Au和沉积ZnO籽晶的硅衬底上分别生长高度有序、垂直密布的直立Zn2GeO4/ZnO纳米棒阵列,利用扫描电子显微镜(SEM)、X射线衍射仪(XRD)和光致发光(PL)谱测试手段对所制备样品进行表征和发光特性的研究。所制备的Zn2GeO4/ZnO纳米棒的直径为350~400 nm,高度为10~11μm;室温PL谱观察到3个来源于Zn2GeO4的典型发光峰。最后,对CVD法制备的Zn2GeO4/ZnO纳米棒生长机理进行了分析。该种直立性良好的一维纳米棒材料可以广泛地应用到纳米光电子器件中。     

以PVP纳米纤维为模板采用原子层沉积法制备MgxZn1-xO纳米纤维及其光学性质研究

采用静电纺丝方法制备聚乙烯吡咯烷酮(PVP)纳米纤维,并以其为模板采用原子层沉积(ALD)方法制备不同Mg掺杂浓度的MgxZn1-xO纳米纤维。研究了不同Mg掺杂浓度对复合纳米纤维结构和光学性质的影响。利用场发射扫描电子显微镜(FESEM)、光致发光(PL)和紫外-可见光(UV-Vis)吸收谱对样品测试并进行表征分析。结果表明,Mg元素的掺入并没有改变ZnO纳米纤维的形貌,所有样品的表面形貌极其相似,只是掺杂后纤维直径有所增大;随着Mg掺杂浓度的增加吸收边逐渐发生蓝移,表明所制备MgxZn1-xO纤维的带隙具有可调节性。与此同时,在PL谱中可以观察到样品的紫外(UV)发光峰从377nm移动至362nm,且与不掺杂的样品相比,MgxZn1-xO纳米纤维的UV发光强度明显增强。通过这种方法可以合成组分可控的MgxZn1-xO纳米纤维。在ZnO中掺入Mg元素可以有效地提高ZnO-PVP纳米纤维的禁带宽度以及UV发射强度。     

有序ZnO纳米阵列的制备及其光学特性

纳米球刻蚀技术和磁控溅射方法在普通玻璃衬底上制备有序氧化锌(ZnO)纳米阵列。利用扫描电子显微镜对样品表面形貌进行了观测,并对样品进行荧光(PL)光谱测试。结果表明,相比于普通ZnO薄膜,ZnO纳米阵列的有序结构可以提高在紫外区域的发光性能,减少蓝绿光的发射缺陷。研究了不同ZnO纳米阵列粒径大小和不同ZnO纳米阵列的厚度对其光学性质的影响。溅射时间30min的有序ZnO纳米阵列样品的质量和结晶状态较好,随着聚苯乙烯(PS)纳米球粒径的减小,样品吸收峰和荧光光谱均发生"蓝移"。     

Fe,Co共掺杂ZnO薄膜结构及发光特性研究

采用溶胶凝胶法在玻璃衬底上制备了Fe,Co共掺Zn0.9FexCo0.1-xO(x=0,0.03,0.05,0.07)系列薄膜.通过扫描电镜(SEM)、X射线衍射(XRD)、X射线光电子谱(XPS)和光致发光(PL)谱对薄膜样品的表面形貌、晶体结构、成分和光学性能进行了研究.XRD结果表明所有ZnO薄膜样品都呈六方纤锌矿结构,在样品中没有观察到与Fe和Co相关的团簇,氧化物及其他杂相的衍射峰,表明共掺杂改善了Fe或Co在ZnO的分散性.XPS测试结果揭示样品中Co离子的价态为+2价;Fe离子的价态为+2价和+3价共存,但Fe相对浓度的增大导致Fe3+含量增加.所有样品的室温光致发光谱(PL)均观察到紫外发光峰和蓝光双峰,其中Fe,Co共掺ZnO薄膜的紫外发光峰较本征ZnO出现蓝移,蓝光双峰峰位没有变化,但发光强度有所减弱;而掺杂ZnO薄膜的绿光发光峰几乎消失.最后,结合微结构和成分分析对薄膜样品的发光机理进行了讨论.     

ZnO：V薄膜后退火处理前后的微结构与发光特性

利用溶胶-凝胶(Sol-gel)法在单晶硅(100)衬底上分别制备了ZnO:V薄膜和纯ZnO薄膜。为进一步研究后退火对ZnO:V薄膜结构和发光性质的影响,在两段式快速退火后又在800℃下进行了后退火处理。X射线衍射的结果表明:后退火处理前,钒(V)的掺入使ZnO结晶质量变差,而800℃退火处理后,从ZnO的衍射峰中可以看出,相对于无V杂样品其结晶质量变好。扫描电子显微镜形貌图中可以看出制备的样品薄膜颗粒大小均匀,薄膜致密度较高。光致发光(PL)谱的研究表明:ZnO:V薄膜在800℃退火处理后,紫外和绿带发光峰均增强,但紫外发光峰增强得更多;与同样条件下制备的纯ZnO薄膜的PL谱比较,发现V掺杂后样品的紫外激子复合发光峰的强度明显增强且峰位发生蓝移,而缺陷引起的绿带发光峰的强度降低。     

单根六方截面ZnO纳米针制备与发光特性

利用气相传输法,以高纯度氧化锌和碳粉为原料,通过高温碳热还原法制备出可分离单根针状ZnO纳米晶体。用XRD、SEM和PL等手段对其进行了表征。结果表明:样品系沿c轴方向生长、具有六方截面自组装ZnO纳米针(线)晶体。除具有一般线状ZnO纳米晶体相似的紫外光激励的PL谱外,在800nm飞秒激光脉冲激励下,从该样品可观测到上转换紫外受激辐射。     

ZnO∶V薄膜后退火处理前后的微结构与发光特性

利用溶胶-凝胶(Sol-gel)法在单晶硅(100)衬底上分别制备了ZnO∶V薄膜和纯ZnO薄膜。为进一步研究后退火对ZnO∶V薄膜结构和发光性质的影响,在两段式快速退火后又在800℃下进行了后退火处理。X射线衍射的结果表明:后退火处理前,钒(V)的掺入使ZnO结晶质量变差,而800℃退火处理后,从ZnO的衍射峰中可以看出,相对于无V杂样品其结晶质量变好。扫描电子显微镜形貌图中可以看出制备的样品薄膜颗粒大小均匀,薄膜致密度较高。光致发光(PL)谱的研究表明:ZnO∶V薄膜在800℃退火处理后,紫外和绿带发光峰均增强,但紫外发光峰增强得更多;与同样条件下制备的纯ZnO薄膜的PL谱比较,发现V掺杂后样品的紫外激子复合发光峰的强度明显增强且峰位发生蓝移,而缺陷引起的绿带发光峰的强度降低。     

超声处理对ZnO薄膜光致发光特性的影响

对于结晶状态好的ZnO薄膜，测量了其光致发光(PL)光谱，发射光谱中只发现了峰值波长约389 nm的近紫外光.样品进行超声处理后，发射谱中不仅观察到近紫外峰，又观察到波长约508 nm的绿光峰.绿光峰的强度比近紫外光的强度强得多，且近紫外峰红移.进一步的热处理使绿光峰大大增强.超声处理改变了ZnO薄膜的质量和结晶状态，使晶格中产生氧空位.处理过程中的热效应使得薄膜晶格振动加剧.当晶格振动加剧到一定程度，晶格中的氧脱离格点形成氧空位.510 nm左右的绿色发光峰是ZnO晶体中的氧空位产生的.薄膜的温度越高， 关键词： ZnO薄膜 超声 光致发光     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.