折衍射混合复消色差望远物镜中的色球差

一个正透镜、一个负透镜及一个衍射光学元件以不同的组合可以构成两种折衍射混合光学系统.当这两种系统消球差、彗差及复消色差后会产生不同的色球差.通过赛德尔像差理论,分析了这两种结构产生不同色球差的原因.计算表明当衍射光学元件以负透镜的平面为基底时产生的色球差为以正透镜的平面为基底时产生的色球差的7倍.对衍射光学元件以负透镜的平面为基底的情形,提出了减小系统色球差的解决办法,使系统色球差减小到0.307 mm.另外设计了一个传统复消色差光学系统,并和折衍射混合光学系统进行了比较,分析表明,衍射光学元件可代替传统光学系统中的特殊光学材料并使系统达到相同的成像质量.最后讨论了衍射光学元件的衍射效率对系统成像质量的影响.     

含有双层衍射光学元件的中波/长波消热差光学系统的设计

建立了工作在一定入射角度范围内的多层衍射光学元件的复合带宽积分平均衍射效率的分析模型。基于衍射光学元件所具有的独特的消色差和消热差性质,设计了一个含有双层衍射光学元件的工作在(3.7~4.8) μm和(7.7~9.5) μm红外双波段光学系统。光学系统的焦距为200 mm,F#为2。采用像元数为320×256、间距为30 μm的制冷型探测器。该系统在空间频率17 lp/mm时,中、长波红外MTF分别高于0.66和0.54;最大RMS半径小于11.702 μm;波前像差小于0.191 7λ;最大离焦量小于焦深;在-55℃~71℃范围内实现了无热化设计。入射到衍射面上的角度为0°~5.19°,该双层衍射光学元件在中波和长波波段的复合带宽积分平均衍射效率分别为99.81%和97.36%。含有双层衍射光学元件的红外双波段光学系统结构简单,像质优良,可以广泛应用于军事探测系统中。     

非制冷长波红外热像仪折衍混合双视场光学系统设计

根据衍射光学元件具有大的负向色散特性,将衍射光学元件应用于红外双视场光学系统中,根据傅里叶光学分析衍射光学元件(DOE)的消色差,列表对比折射透镜与衍射光学透镜的特性,并给出变倍比为4∶1可用作非制冷红外热像仪的光学系统的具体设计实例.系统采用切入式变焦方式,在短焦时切入2片透镜实现宽视场,通过引入二元面和非球面提高了成像质量.设计结果表明:在空间频率11 lp/mm处,短焦距40 mm时,各个视场的MTF值均大于0.6;长焦距160 mm时,各个视场的MTF值均大于0.7,宽视场和窄视场都具有较好的成像质量.     

衍射光学透镜色散特性的仿真研究

在白光照射下,衍射光学透镜的焦距不仅同材料色散和波长色散有关,而且还同孔径因子有关。基于折射率随波长变化的经验公式,利用自编的仿真计算程序包,得到了透镜焦距、材料色散、波长色散、孔径因子之间的关系曲线。所获得的理论分析和仿真计算结果为进一步设计消色差的纯衍射目视光学系统提供了理论依据,具有一定的指导意义。     

多级衍射元件消色差系统的面型分析

多级衍射元件在衍射望远系统消色差领域的应用逐渐成为热点。基于赛德尔三级像差理论，对由多级衍射光学元件、折射光学元件和菲涅耳衍射元件三元件组合的光学系统展开分析。在400～700 nm工作波段，通过数学推导校正表面系统的球差，同时实现消色差及复消色差。对系统在平面、球面和非球面不同面型下的成像质量进行比对。当系统为非球面设计时，调制传递函数在截止频率50 lp/mm处高于0.6683，优于平面和球面设计，衍射圈入能量更高，成像质量更好。该研究为将多级衍射元件组合系统运用到消色差领域提供了参考。     

基于柯西色散公式的多层衍射光学元件的设计和分析

以衍射光学元件相位延迟表达式为理论基础,采用光学材料的折射率柯西色散近似公式,研究并得到了多层衍射光学元件的相位延迟与材料的关系,以及衍射效率与设计波长的关系.在400～700 nm可见光波段,以聚甲基丙烯酸酯和聚碳酸酯为基底材料,由柯西色散近似公式设计的多层衍射光学元件的最大带宽积分平均衍射效率为99.62%,相应的...     

多层衍射光学元件设计原理与衍射效率的研究

叙述了多层衍射光学元件的设计原理.通过对多层衍射光学元件结构、位相延迟表达式、材料选择匹配的研究,使得优化最大光栅高度后的多层衍射光学元件能够实现大幅度提高宽光谱范围内衍射效率的作用.其衍射效率在从g谱线（435.834 3 nm）到C谱线（656.272 5 nm）的可见光范围内的任何波长上的理论衍射效率均在99％以上,带宽积分平均衍射效率为99.7％,能够满足高质量成像光学系统应用的需要,并利用该元件设计了长焦距复消色差物镜.     

含有双层谐衍射元件的红外双波段光学系统消热差设计

用投影无热差图和双层衍射元件选玻璃的原则,选择了适用红外双波段消热差、消色差的玻璃组合.为提高衍射效率,基于双层衍射元件衍射效率表达式研究了双层谐衍射元件的结构优化,给出了优化方法.利用双层谐衍射元件设计的折衍混合双波段光学系统视场角10°,F#为2,有效焦距115 mm.系统在3.4~4.2 μm和8~11 μm两个工作波段的衍射效率均达到90%以上;－40~100℃温度范围内,中心视场的调制传递函数值变化最大为0.09、边缘视场的调制传递函数值变化最大为0.13.     

用按需滴定技术制备聚合物微透镜阵列

采用高分子聚合物-单体混合溶液按需滴定-原位热聚合的新方法制作折射微透镜及其阵列.制备透镜的主要材料是甲基丙烯酸甲酯及其聚合物.制备的微透镜直径在1 mm～3 mm范围内,矢高为100 μm～400 μm,透镜焦距在1 mm～4 mm之间.所得微透镜在波长λ=1.55 μm处有很好的光学透过率(90%),适于作光通信耦合器件.用AFM-Ⅱ型原子力显微镜测得微透镜阵列的表面粗糙度Ra约等于0.9 nm,并通过液体的表面张力理论分析了微透镜的形成机理.     

新型轻量化可见光光谱仪成像系统研究与分析

利用衍射光学元件消色差和对波面进行任意整形及自由曲面光学元件校正像差的特性,将衍射光学元件和自由曲面光学元件应用于传统可见光光谱成像光谱仪成像系统中,提出了一种新型的可见光光谱成像光谱仪成像系统,基于衍射光学元件独特的负色散特性,用一片折射/衍射混合光学元件代替传统的双胶合透镜来实现消色差,基于自由曲面光学元件的多自由度特性,在系统中引入两个自由曲面光学元件对系统中的像差进行有针对性的校正,针对具体的设计实例给出了详细的设计步骤,设计结果表明,在相同的参数指标前提下,新型系统仅为4片式结构,和传统系统相比,重量减轻22.9%,总长缩短26.6%,最大口径减小30.6%,调制传递函数值最大提升为1.0视场,调制传递函数值提高0. 35,最大畸变减小1.6%,最大垂轴像差减小56.4%,轴向色差减小59.3%,新型系统各方面的性能都得到了较大的改进,为现代高性能、轻小型可见光光谱成像光谱仪成像系统设计提供了一种新的途径。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.