基于法布里-珀罗标准具和多光栅校准的光纤布喇格光栅波长解调系统

为了消除由法布里-珀罗标准具的干涉峰偏移引起的光纤布喇格光栅波长解调误差,采用多参考光栅进行法布里-珀罗标准具波长校准,搭建了相应的光纤布喇格光栅解调平台.将待解调光栅、法布里-珀罗标准具和多个参考光栅分别接入采样通道,用多个参考光栅对法布里-珀罗标准具进行波长校准,得到准确度较高的标准具干涉峰波长,再以此波长计算待测光栅波长,降低了校准误差.实验结果表明,利用该方法搭建的光纤布喇格光栅解调系统校准的重复性误差小于1.6pm,波长解调误差低于1.8pm.     

一种同时测量电流和温度的光纤光栅传感器

提出了一种基于光纤光栅法布里-珀罗干涉仪且可以同时测量交变电流和温度的传感器,并对其进行了理论分析和实验研究.该传感器采用单频激光入射,作为反射镜的一对光纤布喇格光栅自由放置,其间的法布里-珀罗腔粘贴在磁致伸缩材料上,通电导线周围的磁场通过磁致伸缩材料作用于光纤光栅法布里-珀罗腔,引起腔长周期性变化.同时,由于热膨胀和热光效应,环境温度的变化会引起光纤长度和折射率的改变,从而改变光纤光栅法布里-珀罗腔的反射光谱特性.通过检测输出光信号的频率和峰值可实现电流和温度的同时测量.对通电线圈的电流及环境温度进行测量的实验结果与理论分析相吻合.     

一种同时测量电流和温度的光纤光栅传感器

提出了一种基于光纤光栅法布里-珀罗干涉仪且可以同时测量交变电流和温度的传感器,并对其进行了理论分析和实验研究.该传感器采用单频激光入射,作为反射镜的一对光纤布喇格光栅自由放置,其间的法布里-珀罗腔粘贴在磁致伸缩材料上,通电导线周围的磁场通过磁致伸缩材料作用于光纤光栅法布里-珀罗腔,引起腔长周期性变化.同时,由于热膨胀和热光效应,环境温度的变化会引起光纤长度和折射率的改变,从而改变光纤光栅法布里-珀罗腔的反射光谱特性.通过检测输出光信号的频率和峰值可实现电流和温度的同时测量.对通电线圈的电流及环境温度进行测量的实验结果与理论分析相吻合.     

基于宽谱光源的光纤传感波长解调系统的研究

研究制作了基于宽谱光源的光纤传感波长解调系统, 以多光纤光栅作为波长参考基准、采用可调谐光纤法布里-珀罗(F-P)滤波器作为波长扫描器件。系统中采用三次多项式拟合的方法对滤波器锯齿波的扫描电压与透射波长关系曲线进行非线性拟合, 解决可调谐光纤F-P滤波器的电压—波长非线性关系对系统测量带来的较大误差问题, 实现波长的高精度解调。采用五光纤光栅做波长参考, 单根光纤光栅传感器的解调实验结果表明：待测光纤光栅布拉格波长短期测量分辨率为3.5 pm, 长期测量稳定性为7 pm。采用该系统对光纤非本征法布里-珀罗干涉型(EFPI)应变传感器的测试结果表明, 测量应变灵敏度为2.41 nm/με, 并且应变和波长之间存在良好的线性关系, 线性相关度达到0.99991。     

基于匹配光纤光栅法布里-珀罗干涉仪的应变解调方法

提出并实验验证了一种基于匹配光纤光栅法布里-珀罗干涉仪的应变传感器解调方法,该方法综合了光纤法布里-珀罗干涉技术和匹配光纤光栅滤波法的优点.通过半导体制冷片和压电陶瓷组成的闭环负反馈控制系统,精确调节匹配光栅法布里-珀罗干涉仪的温度和应变,有效解决了光栅法布里-珀罗干涉仪的失配问题,从而保证系统静态工作点处于最佳匹配位置,同时能够避免探头因环境温度波动导致的测量误差.实验结果表明,该系统能够响应50~800 Hz的输入信号,应变最小分辨力至少为0.4 nε/Hz^1/2,解调灵敏度高,且不受环境温度波动的影响,因而在动态应变或振动测量中具有较高的实用性.     

基于匹配光纤光栅法布里-珀罗干涉仪的应变解调方法

提出并实验验证了一种基于匹配光纤光栅法布里-珀罗干涉仪的应变传感器解调方法,该方法综合了光纤法布里-珀罗干涉技术和匹配光纤光栅滤波法的优点.通过半导体制冷片和压电陶瓷组成的闭环负反馈控制系统,精确调节匹配光栅法布里-珀罗干涉仪的温度和应变,有效解决了光栅法布里-珀罗干涉仪的失配问题,从而保证系统静态工作点处于最佳匹配位置,同时能够避免探头因环境温度波动导致的测量误差.实验结果表明,该系统能够响应50～800Hz的输入信号,应变最小分辨力至少为0.4nε/Hz1/2,解调灵敏度高,且不受环境温度波动的影响,因而在动态应变或振动测量中具有较高的实用性.     

可调谐法布里-珀罗滤波器的高精度大范围实时定标

将乙炔(C2H2)气体的吸收光谱作为标准波长参考,对可调谐光纤法布里-珀罗滤波器进行波长实时定标,使解调系统的测量精度提高到1 pm.根据可调谐光纤法布里-珀罗滤波器谐振波长的周期性,提出了大波长范围的波长定标方法,从而可以在1525～1615 nm的范围内对可调谐光纤法布里-珀罗进行精确定标,实现了高精度大波长范围的信号探测.相比于传统的以光纤光栅作为波长参考的定标方法,该方法的测量精度、测量范围、系统运行可靠性都大为改善.     

基于Terfenol-D材料和光纤光栅法布里珀罗腔的磁场传感器（英文）

基于Terfenol-D磁致伸缩材料和光纤光栅法布里珀罗腔,提出了一种用于微弱静态磁场测量的光纤磁场传感器.为了提高传感器的分辨率,采用钕铁硼永磁体提供偏置磁场,同时,采用Monel-400合金与光纤光栅法布里珀罗腔耦合的方式,作为参考元件,对传感器进行温度补偿.实验测得传感器的磁场灵敏度为1.7×10~(-3) pm/μT,磁场分辨率为3.0μT。实验结果表明,本传感器对于静态磁场响应具有良好的线性度和指向性,可用于微弱磁场测量.     

光纤微机电系统法布里-珀罗压力传感器的波分复用

提出了一种用阵列波导光栅复用光纤微机电系统法布里-珀罗压力传感器的方法,实现了法布里-珀罗压力传感器的准分布式测量。传感器基于法布里-珀罗腔干涉的原理,采用微机电系统技术加工制作,用双波长方法解调干涉信号,利用传感器对两个不同波长光的反射率的比值与压力的单值关系确定所施加压力的大小,用阵列波导光栅实现传感器复用。理论分析与实验验证了传感器解调和复用的基本原理。实验结果表明:在压力的线性测量范围(0~1.5 MPa)内,系统的灵敏度(相对反射率比值/压力)可达到0.02026 MPa-1,测量结果具有较好的线形性,相对反射率比值的标准偏差小于3×10-4。该系统可以补偿传感器光网中和波长无关的变动引起的误差,具有好的线性、灵敏度和精度,复用能力强且复用传感器间无串扰。     

光纤光栅法布里-珀罗传感器频分复用技术

理论分析了光纤光栅法布里-珀罗(F-P)传感器频分复用技术的原理,并给出了信号处理对腔长选取的要求。数值模拟结果表明,不同腔长的传感器具有不同的谐振条纹频率,为保证频域中的信号不发生重叠,要求不同光纤光栅法布里-珀罗传感器间的腔长之差必须大于光纤光栅的长度。进一步的实验及模拟分析结果发现,温度等待测量的变化仅仅使光纤光栅法布里-珀罗传感器的反射光谱整体平移,相应的频域信号只产生相移而形状不发生变化,因而不能采用普通光纤法布里-珀罗(FFP)传感器的腔长傅里叶变换解调法解调频分复用光纤光栅法布里-珀罗传感器的信号。根据这一特点,提出了利用自相关分析实现频分复用传感器系统信号解调的方案。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.