基于氧化锌纳米线的紫外发光二极管

构建了基于n-ZnO纳米线/p-Si异质结的紫外发光二极管.ZnO纳米线准阵列采用水热法生长于重掺p型Si片上.此法简易，反应温度低，易于大规模生产；其产物ZnO纳米线结晶良好，以c轴为优势取向，光激发下的紫外荧光发射很强.二极管的电学接触采用聚合物填充的In阴极或以氧化铟锡(ITO)玻璃紧压形成阴极.它们的I-V特性体现出良好的二极管性质.在正向偏置电压驱动下，构建的发光二极管可稳定发射波长在387nm的较强的近紫外光和较弱的绿光. 关键词： ZnO纳米线 异质结 电致发光 水热法     

n-ZnO/i-MgO/p-GaN异质结发光二极管

用等离子体辅助分子束外延的方法生长了n-ZnO/i-MgO/p-GaN异质结发光二极管。I-V测量表明其具有典型的二极管整流特性。电致发光峰位于382nm,通过与n型ZnO和p型GaN的光致发光谱比较,其发光峰位与线形都与ZnO的自由激子发射一致,表明该电致发光来自于ZnO的自由激子发射。通过Anderson模型比较了n-ZnO/i-MgO/p-GaN和n-ZnO/p-GaN异质结的能带示意图,证明了由于MgO层的插入抑制了ZnO向GaN层中的电子注入,且有利于空穴向ZnO层注入,从而实现了ZnO层中的电注入发光。     

一维纳米氧化锌自驱动紫外探测器的构建与性能研究

本文通过化学气相沉积法制备了ZnO纳米材料, 利用扫描电镜、光致发光谱、X衍射光谱及拉曼光谱等方法对制备的材料进行了表征. 基于制备的单根ZnO线分别构建了三种不同结构的紫外探测器件: Ag-ZnO-Ag肖特基型、PEDOT:PSS/n-ZnO结型和p-Si/n-ZnO结型紫外探测器, 并对器件的性能进行了研究. 结果表明: 三种不同结构的器件都表现出良好的整流特性, 对紫外线均有明显的光响应; 在零偏压下, 都有明显的自驱动特性. 三种器件中, p-Si/n-ZnO型紫外探测器性能最为优异: 在零偏压下, 暗电流约在1.2×10^-3 nA, 光电流在5.4 nA左右, 光暗电流比为4.5×10³, 上升和下降时间分别为0.7 s和1 s. 通过三类器件性能比较, 表明无机p-Si更适合与ZnO构建pn结型自驱动紫外探测器.     

ZnO:Al薄膜中本征缺陷对光电效应的影响

在直流溅射法制备ZnO薄膜的过程中,通过合适选取溅射时氧氩的压力比,可以显著提高所得n-ZnO／p-Si异质结的光生短路电流,并且对该异质结的光生开路电压没有明显影响,从而可以用这种方法明显提高其光电转化能力。即使是在已经进行了n型掺杂的ZnO薄膜(这里为ZnO：Al)中,改变溅射时氧氩比对光电效应的影响也很明显。通过实验,已经证实了产生这种现象的原因是溅射时氧氩比的改变导致了ZnO薄膜内部的本征缺陷浓度的改变,使得载流子浓度变化而导致的结果。在氧氩压力比约为1：3时,光电转化效率最高。     

退火对ZnO薄膜晶体结构和ZnO/p-Si异质结光电性质的影响

采用脉冲激光沉积方法在p-Si(100)衬底卜牛长ZnO薄膜,分别在500℃、600℃和700℃下真空退火,采用X射线衍射仪研究了退火对ZnO薄膜品体结构的影响,并测量了ZnO的面电阻和ZnO/p-Si异质结的、I-V特性曲线.研究表明,随着退火温度的升高,ZnO的(002)衍射峰强度逐渐增大,半峰全宽不断减小,同时薄膜内应力减小,ZnO晶粒尺寸变大.表明高温退火有助于ZnO薄膜结晶质量的提高.在没有光照的条件下,异质结的漏电流随退火温度的增加而增大;用650 nm光照射样品时,600℃退火的样品表现出最明显的光电效应,而过高的退火温度会破坏ZnO/p-Si异质结的界面结构,使其光电流变小.所以,要得到性能良好的光电器件,应选取适当的退火温度.     

超声处理对ZnO薄膜光致发光特性的影响

对于结晶状态好的ZnO薄膜，测量了其光致发光(PL)光谱，发射光谱中只发现了峰值波长约389 nm的近紫外光.样品进行超声处理后，发射谱中不仅观察到近紫外峰，又观察到波长约508 nm的绿光峰.绿光峰的强度比近紫外光的强度强得多，且近紫外峰红移.进一步的热处理使绿光峰大大增强.超声处理改变了ZnO薄膜的质量和结晶状态，使晶格中产生氧空位.处理过程中的热效应使得薄膜晶格振动加剧.当晶格振动加剧到一定程度，晶格中的氧脱离格点形成氧空位.510 nm左右的绿色发光峰是ZnO晶体中的氧空位产生的.薄膜的温度越高， 关键词： ZnO薄膜 超声 光致发光     

氧化锌薄膜Zn/O比和发光性能的关系

用直流反应溅射在硅基片上生长具有高取向晶粒的氧化锌薄膜,在氧气、氮气、空气气氛和不同温度下进行热处理,对所得到的样品用俄歇谱(AES)仪进行元素深层分布分析,并测量光致发光光谱。研究结果表明：1．经热处理的薄膜表面全部为缺氧表面,不同深度Zn和O含量分布(Zn／O)有所不同;2．当在氧气氛中1000℃下热处理后,在薄膜的深层可产生比较明显的氧过量;而在空气中950℃下热处理后,则可产生局部氧过量;3．光致发光谱表明,薄膜中全部为锌过量时产生纯紫外发射,而具有局部氧过量的薄膜则在产生紫外发射的同时产生绿色发光,绿光和紫外的强度比则随局部氧过量增多而增大。     

ZnO/Si异质结的光电转换特性研究

利用直流反应溅射方法在p型Si衬底上生长掺Al的n型ZnO薄膜,测量了由n型ZnO薄膜和p型Si衬底组成的异质结在黑暗和光照条件下的I-V特性,结果表明该异质结具有优良的整流特性,而且在光照条件下的反向电流迅速增大并很快趋于饱和.通过测量ZnO薄膜的光电流和异质结的光电压的光谱响应,初步分析了异质结的光电转换机理.测量结果显示,在入射光波长为380nm时光电流强度明显下降,反映出光电流与ZnO薄膜禁带宽度的密切关系;同时还发现,在与ZnO禁带宽度相对应的波长前后所产生的光生电压方向相反.推测这一现象与异质结的能带结构密切相关. 关键词： ZnO薄膜 异质结 光电转换 光谱响应     

TiO_2薄膜的硼掺杂对TiO_2/p~+-Si异质结器件电致发光的增强

利用磁控溅射在重掺硼硅(p+-Si)衬底上分别沉积TiO2薄膜和掺硼的TiO2(Ti O2∶B)薄膜,并经过氧气氛下600℃热处理,由此形成相应的TiO2/p+-Si和TiO2∶B/p+-Si异质结。与Ti O2/p+-Si异质结器件相比,TiO2∶B/p+-Si异质结器件的电致发光有明显的增强。分析认为:TiO2∶B薄膜经过热处理后,B原子进入TiO2晶格的间隙位,引入了额外的氧空位,而氧空位是TiO2/p+-Si异质结器件电致发光的发光中心,所以上述由B掺杂引起的氧空位浓度的增加是TiO2∶B/p+-Si异质结器件电致发光增强的原因。     

CVD两步法生长ZnO薄膜及其光致发光特性

用CVD两步法在常压下于p型Si(100)衬底上沉积出具有较好择优取向的多晶ZnO薄膜。在325nm波长的光激发下,室温下可观察到显著的紫外光发射(峰值波长381nm)。高温退火后氧空位缺陷浓度增加,出现了一个450~600nm的绿光发光带,发光峰值在510nm。作为比较,用一步法生长的ZnO薄膜结晶质量稍差。在其PL谱中不仅有峰值波长389nm的紫外发射而且还出现了一个很强的蓝光发光中心(峰值波长437nm),退火后同样产生绿光发光带。对这两种绿光发光带的发光机制进行了研究,认为前者源于VO,而后者与O_Zn有密切的关系。     

Computer-assisted analysis and calculation of phase diagrams of the Fe---Cr---O, Fe---Ni---O and Cr---Ni---O systems

Available thermodynamic and phase equilibrium data for the Fe---Cr---O, Fe---Ni---O and Cr---Ni---O systems are assessed and equations for the free energies of the phases as functions of composition and temperature are derived. With these mathematical expressions and with a computer program written for the purpose, phase diagram sections at constant temperature, or at constant log p_O2, or at constant P_co/P_co2 or p_H2/P_H2O ratios can be calculated at all compositions and over a wide range of temperature and oxygen potential. The representation and analysis of the phase equilibria are greatly facilitated through the use of isothermal log P_O2-composition phase diagrams which are discussed in some detail. Structural models for the spinel phases are examined.     

Oxygen transfer processes in (La,Sr)MnO3/Y2O3-stabilized ZrO2 cathodes: an impedance spectroscopy study

Impedance spectroscopy was used to study the oxygen reaction kinetics of La_0.8Sr_0.2MnO₃ (LSM)-based electrodes on Y₂O₃-stabilized ZrO₂ (YSZ) electrolytes. Three types of electrodes were studied: pure LSM, LSM–YSZ composites, and LSM/LSM–YSZ bilayers. The electrodes were formed by spin coating and sintering on single-crystal YSZ substrates. Measurements were taken at temperatures ranging from 550 to 850°C and oxygen partial pressures from 1×10⁻³ to 1 atm. An arc whose resistance R_el had a high activation energy, E_a=1.61±0.05 eV, and a weak oxygen partial pressure dependence, (P_O2)^−1/6, was observed for the LSM electrodes. A similar arc was observed for LSM–YSZ electrodes, where R_el(P_O2)^−0.29 and the activation energy was 1.49±0.02 eV. The combination of a high activation energy and a weak P_O2 dependence was attributed to oxygen dissociation and adsorption rate-limiting steps for both types of electrodes. LSM–YSZ composite cathodes showed substantially lower overall interfacial resistance values than LSM, but exhibited an additional arc attributed to the resistance of YSZ grain boundaries within the LSM–YSZ. At 850°C and low P_O2, an additional arc was observed with size varying as (P_O2)^−0.80 for LSM and (P_O2)^−0.57 for LSM–YSZ, suggesting that diffusion had become an additional rate limiting step. Bilayer LSM/LSM–YSZ electrodes yielded results intermediate between LSM and LSM–YSZ. The results showed that most of the improvement in electrode performance was achieved for a LSM–YSZ layer only ≈2 μm thick. However, a decrease in the grain-boundary resistance would produce much better performance in thicker LSM–YSZ electrodes.     

Transient creep of YBa2Cu3O7−x superconductor

Rapid changes of oxygen partial pressure (P_O2) between 10³ and 2.1×10⁴ Pa have been carried out during steady-state plastic deformation of polycrystalline YBa₂Cu₃O_7−x (YBCO) at temperatures between 825 and 900°C. Transient creep was observed after such P_O2 changes. The analysis of these creep transients allowed the determination of the chemical diffusion coefficient for reequilibration, which is identical to that found from thermogravimetry and electrical conductivity experiments for oxygen vacancies.     

Mixed conductivity in SrCe0.95Yb0.05O3 protonic conductors

The results of electrical conductivity measurements on SrCe_0.95Yb_0.05O₃ under controlled oxygen partial pressure and temperature are presented. A defect model consistent with experimental results is proposed which provides for P_O2^−1/4 dependent n-type, P_o2-independent oxygen ion and P_O2^+1/4 dependent p-type conductivity components. The band gap, reduction, oxidation and ion-migration energies are determined from an analysis of the data in terms of the proposed defect model. These results suggest that some earlier data interpreted in terms of protonic conduction may require re-evaluation.     

Ni/Au与N掺杂p型ZnO的欧姆接触

研究了Au,In,Ni/Au三种不同金属膜与N掺杂p型ZnO的接触特性,发现Ni/Au双层膜更适合作为其欧姆电极材料,并比较了不同气氛和不同温度退火对Ni/Au电极的影响.发现在O₂中退火电极性能发生蜕变,而在N₂中退火性能得到改善.指出即使在N₂中退火,退火温度的选择也是至关重要的,本实验在400℃,氮气气氛下退火150s,得到了较好的欧姆接触特性.     

Annealing effects on the properties of Ga2O3 thin films grown on sapphire by the metal organic chemical vapor deposition

We have prepared the gallium oxide (Ga₂O₃) thin films on sapphire substrates by the metal organic chemical vapor deposition (MOCVD) technique. We have compared the two films with and without the thermal annealing by using the X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and the photoluminescence (PL) spectra. Postdeposition annealing of amorphous Ga₂O₃ films was found to increase the degree of crystallization and the surface roughness. The PL emission intensities of bands in the blue–green and the ultraviolet regions increased by the thermal annealing.     

Ionic and electronic conductivity in lead–zirconate–titanate (PZT)

Accurate impedance measurements on differently sized samples of lead–zirconate–titanate (PbZr_0.53Ti_0.47O₃, PZT) have been analyzed with a CNLS procedure, resulting in the separation of the ionic and electronic conductivities over a temperature range from 150 to 630 °C. At 603 °C the electronic conductivity shows approximately a (P_O2)^1/4 dependence, while the ionic conductivity remains constant. Below the Curie transition temperature the oxygen non-stoichiometry becomes frozen-in and the conductivities are strongly dependent on the sample history with respect to temperature sequence and ambient P_O2. A tentative interpretation assumes defect association, i.e. formation of neutral [V_Pb–V_O^··]^× complexes, and electron-hole transfer between lead sites and lead vacancies to control the oxygen ion conductivity in the tetragonal phase.

Annealing PZT-based devices at about 600 °C under low oxygen pressure (1 Pa oxygen) effectively decreases the low temperature electronic conductivity by a factor of 100 and the ionic conductivity by a factor of 10–15 with respect to normal air processing.     

Effects of substitution of Ti for Fe in BiFeO3 films prepared by sol–gel process

Ti substituted BiFe_1−xTi_xO_3+δ films have been prepared on indium–tin oxide (ITO)/glass substrates by the sol–gel process. The films with x=0.00–0.20 were prepared at an annealing temperature of 600 °C. X-ray diffraction patterns indicate that all films adopt R3m structure and the films with x=0 and 0.10 show pure perovskite phase. Cross-section scanning shows the thickness of the films is about 300 nm. Through 0.05 Ti substitution, the 2P_r increases to 8.30 μC/cm² from 2.12 μC/cm² of the un-substituted BiFeO₃ film and show enhanced ferroelectricity at room temperature. The 2P_r values are 2.63 and 0.44 μC/cm² for the films with x=0.01 and 0.2, respectively. Moreover, the films with x=0.05 and 0.10 show enhanced dielectric property since the permittivity increases near 150 at the same measuring frequency. Through the substitution of Ti, the leakage conduction is reduced for the films with x=0.05–0.20.     

Ultrathin films of lead oxide on gold: Dependence of stoichiometry, stability and thickness on O2 pressure and annealing temperature

Ultrathin oxide films grown in vacuum are important in many industrial areas, including microelectronics and heterogeneous catalysis. In this paper, the dependence of oxide stoichiometry, growth kinetics, thickness and stability on O₂ pressure and annealing temperature are explored using a high-stability quartz-crystal microbalance and Auger spectroscopy, for the oxidation of lead on gold as a model system. The oxide thickness increases abruptly at specific values of the O₂ pressure, as explained previously using Gibbs free energies. A qualitative difference is found between lead-oxide films which are 1 monolayer thick and those which are 2 or more monolayers thick; the former apparently involve exclusively chemisorbed oxygen and can be oxidized and reduced reversibly using thermal oxidation/annealing cycles, whereas the latter involve an extended lead oxide, are more thermally stable, and have a smaller electron inelastic mean free path. Accurate values of the O₂ sticking probability are obtained.     

玉米蛋白质基底上射频磁控溅射法制备ZnO薄膜

采用射频磁控溅射方法在蛋白质基底上成功地制备了ZnO薄膜,研究了不同靶基距、氩氧比和溅射功率条件对ZnO薄膜性质的影响。结果表明,较小的靶基距有助于ZnO薄膜的c轴择优取向生长。我们还发现,沉积于玉米蛋白质基底的ZnO薄膜存在不同程度的张应力,当Ar/（Ar+O₂）为0.7时,ZnO薄膜内的张应力最小。ZnO近带边发光峰有不同程度的红移,我们认为,这是由于晶界势垒和氧空位V_o造成的。随着溅射功率的增大,薄膜生长速率显著加快,晶粒尺寸增大,ZnO的近带边发光峰位逐渐趋向于理论值。