数值模拟激光加载L_2铝板材高速成形瞬态响应

采用ABAQUS有限元仿真软件对激光加载L2铝板材高速成形进行数值模拟,研究了单脉冲激光冲击下成形的瞬态响应过程,获得了激光加载冲击成形过程中位移、速度、应变及应变率等特征量的变化特点.模拟表明,冲击后靶材中心区域发生明显塑性变形,变形截面呈锥形.高速成形过程中,金属板材首先发生振荡幅度非常大的快速弹性变形,其后进入减幅振荡直至静态,激光冲击成形时间在毫秒量级.板材不同节点的位移变化趋势相同,靠近中心区域位移大,边界区域位移小.成形中板材的中心区域速度最大达3 700m/s,变形过程前2μs内应变率急剧变化,最大达104~105 s-1量级.     

超高应变率载荷下铜材料层裂特性研究

超高应变率载荷下材料层裂特性研究对理解极端条件下材料动态破坏特性具有重要意义.利用双温模型结合分子动力学模拟研究分析了超高应变率载荷下铜材料的层裂特性,发现当应变率在10~9s~(-1)—10~(10)s~(-1)内时,铜材料层裂强度在19 GPa附近波动.而当材料发生冲击熔化时,铜的层裂强度下降到14.89 GPa.利用飞秒激光对铜样品靶进行冲击加载,并利用啁啾脉冲频谱干涉技术开展超快诊断,通过单发次实验测量获得了样品靶的自由面粒子速度演化历史,结果未见表征样品层裂的速度回跳和速度周期性振荡信号.结合冲击动力学理论得到样品自由面附近最大加载压强为8.18 GPa,小于超高应变率载荷下铜材料的层裂强度.此外,对回收样品扫描分析发现,铜样品未发生层裂且飞秒激光引起的冲击波对样品表面结构产生了很大影响.     

飞秒激光烧蚀金属靶的冲击温度

在明确飞秒激光与物质相互作用过程冲击温度概念的基础上, 讨论了飞秒激光烧蚀铝靶和铜靶过程中的冲击温度与其他物理量的关系, 利用飞秒激光烧蚀金属的双温模型提取了冲击温度的绝对值, 基于非傅里叶热传导模型计算了冲击温度的分布. 此项研究结果对飞秒激光安全加工含能材料有借鉴意义. 关键词： 飞秒激光 含能材料 烧蚀 冲击温度     

强脉冲激光在AZ31B镁合金中诱导冲击波的实验研究

为了研究强脉冲激光在镁合金中诱导冲击波的衰减,采用Nd:Glass脉冲激光(1054 nm,23 ns)对AZ31B变形镁合金试样表面进行冲击,并利用响应快、测量范围大的PVDF压电膜传感器以及示波器实时测量了强脉冲激光在镁合金靶中诱导激光冲击波的相对压力.根据冲击波每次在靶材背面反射时,所经过距离的不同得到激光冲击波在镁合金中的衰减规律.结果表明,在激光能量为5J的强脉冲激光作用下,镁合金中冲击波衰减的平均速度为5.83×10³ m/s,与镁合金中应力波纵波的传播速度相符;强脉冲激光诱导冲击波在镁合金中是以指数规律衰减的.试验所得分析结果对激光冲击强化镁合金的应用具有重要意义. 关键词： 激光 镁合金 压电膜传感器 衰减规律     

飞秒激光烧蚀固体靶的冲击压强

在明确飞秒激光与物质相互作用过程中冲击压强和冲击温度概念的基础上, 讨论了飞秒激光烧蚀铝、铜、硅三种固体靶过程中的冲击压强与其他物理量的关系, 利用飞秒激光烧蚀固体靶的时间分辨泵浦探测阴影图提取了冲击压强的绝对值. 此项研究结果对飞秒激光安全加工含能材料以及飞秒激光推进技术有重要意义. 关键词： 飞秒激光 含能材料 冲击压强 冲击温度     

2024铝合金激光多次冲击诱导残余应力状态分布规律

采用高功率激光器多次冲击2024铝合金,用X射线衍射技术分析了冲击区域的残余应力,研究了冲击残余应力状态分布规律,并用其评价激光冲击强化效果。研究表明,随着冲击次数增加,塑变量及塑性应变梯度逐渐减小,测点是双向压应力状态,而4次冲击时,塑性应变梯度增大,光斑中心是单向压应力状态,其他点是双向压应力状态。当激光功率密度为2.8 GW/cm2时,3次冲击强化效果最佳,材料是二向压应力状态,残余最大主应力及应力强度的均值最大,方差最小,分布基本均匀,塑性应变梯度较小。     

飞秒激光脉冲作用下氧化镁的烧蚀及其超快动力学过程

研究了双面抛光氧化镁单晶（111）表面800 nm飞秒激光单脉冲烧蚀阈值和激光脉宽的依赖关系.利用泵浦-探针技术，测量不同能量和脉宽作用下飞秒激光烧蚀的时间分辨反射率的演化.通过扫描电镜观察其烧蚀形貌，发现大量的沿氧化镁［100］晶向开裂的裂纹.讨论了表面裂纹的形成机理，并解释了飞秒激光烧蚀氧化镁的超快动力学过程.     

4H-SiC压力敏感膜片的低损伤飞秒激光加工

采用飞秒激光加工4H-SiC压力敏感膜片,研究了飞秒激光深度方向步进间距、扫描路径方向、单脉冲能量、扫描线间距等参数对4H-SiC烧蚀形貌和烧蚀速率的影响。实验结果表明,飞秒激光加工4H-SiC样品表面孔洞的形成主要与激光诱导微沟槽的重叠有关,激光能量分布更均匀能够有效减少4H-SiC被烧蚀表面的激光诱导微沟槽的数量,增大激光扫描路径与激光偏振方向的夹角能够有效降低激光诱导微沟槽的重叠概率,从而抑制孔洞的形成。采用优化后的飞秒激光加工工艺参数,制备出直径为1 600μm、厚度为100μm的4H-SiC压力敏感膜片。所制备的4H-SiC压力敏感膜片表面无明显孔洞,边缘过烧蚀深度小于10μm,实现了4H-SiC压力敏感膜片的低损伤飞秒激光加工。     

惯性对多孔金属材料动态力学行为的影响

 对泡沫金属材料的力学性能已经进行了十分广泛的研究,但在对泡沫金属的应变率效应和惯性效应的研究中,尚存在一些矛盾的结论。为进一步认清惯性在多孔金属动态响应中的作用,用有限元计算方法模拟了二维Voronoi蜂窝的动态压缩行为,得到了不同速度下Voronoi蜂窝的3种变形模式。通过改变基体材料的密度和冲击速度进行“数值实验”,得到了相应“试件”的由冲击面和支撑面得到的宏观平均应力应变曲线和平台应力。根据数值模拟的结果,着重分析了惯性效应的影响。研究发现,惯性并不影响蜂窝的应力应变曲线,但它导致试件中宏观变形不均匀,是平台应力提高的主要原因。     

飞秒脉冲激光作用下金属薄膜的热弹性研究

利用双曲-双温两步热传导和热电子崩力模型,考虑到晶格温度与应变速率的耦合效应,得到了用于描述飞秒激光作用下金属薄膜热力效应的超快热弹性模型。以飞秒脉冲激光辐照金属铜薄膜为例,运用具有人工粘性和自适应步长的有限差分算法,对不同能量密度和脉冲宽度条件下薄膜体内温度场和应力场的变化规律进行了数值模拟,对比分析了电子晶格耦合系数对超快加热过程的影响。结果表明,飞秒脉冲激光辐照早期为明显的非平衡加热过程,电子温度迅速升高,而晶格温度的升高却相对较慢;激光辐照早期的热力耦合效应导致薄膜前表面附近的热应力表现为压应力,随着时间的推移,热应力由压应力转变为张应力,为激光加工和激光对抗提供了理论参考。     

Self-organization of five species in a cyclic competition game

Cyclic competition game models, particularly the “rock–paper–scissors” model, play important roles in exploring the problem of multi-species coexistence in spatially ecological systems. We propose an extended “rock–paper–scissors” game to model cyclic interactions among five species, and find that two of the five can coexistent when biodiversity disappears, which is different from the “rock–paper–scissors” game. As the number of fingers is five, we named the new model the “fingers” game, where the thumb, forefinger, middle finger, ring finger, and little finger cyclically dominate their subsequent species and are dominated by their former species. We investigate the “fingers” model in two ways: direct simulations and nonlinear partial differential equations. An important finding is that the number of species in a cyclic competition game has an influence on the emergence of biodiversity. To be specific, the “rock–paper–scissors” model is in favor of maintaining biodiversity in comparison with the “fingers” model when the variables (population size, reproduction rate, selection rate, and migration rate) are the same. It is also shown that the mobility and reproduction rate can promote or jeopardize biodiversity.     

Contrastive analysis on tone between Putonghua and Taiwan Mandarin

The differences of the pitch and duration of Chinese syllables between Putonghua （PTH） and Taiwan Mandarin （TM） were studied. The speech materials to be used are not only isolated syllables, but also sentences. The results reveal that： For the isolated syllables, T1 and T2 in TM are influenced by Minnan dialect, therefore their pitch are lower than those in PTH. T3 is fall-rise in PTH, while it is fall in TM. Moreover, the syllable duration sequence for different tone is T3〉T2〉T1〉T4 in PTH, while it is T1〉T2〉T3〉T4 in TM. For the syllables in sentences, T2 is mid-rise in PTH, while it is mid-level in TM. And the T3 is longer than T4 but shorter than T1 or T2 in PTH, while it is the shortest in TM. Furthermore the effects of prosodic phrase boundary on duration for different tones are almost the same in PTH, but the lengthening part of T1 or T2 is longer than that of T3 or T4 in TM.     

Experimental study on downstep in Chinese intonation

Downstep in pitch contour of Chinese Putonghua is examined using subtly designed sentences by controlling tone combinations. The results show both automatic and nonautomatic downstep phenomena exist in Chinese. In non-automatic downstep, low tones compress downwards the pitch range of the following syllables. and the main influence of downstep is on topline. Low tone not only lower the topline behind it, but also raise the high tones before it, the effects are compatible with each other. In automatic downstep, the topline of pitch contour in intonational phrase is presented as a linear downtrend, but it differs among speakers due to the effect of personal stress practice. In comparison with downstep phenomenon in other tone or non-tone languages, the downstep ratio in Chinese is not constant, and the domain of downstep is not limited within the adjacent tones.     

Abelian-Higgs phase of SU(2) QCD and glueball energy

It is shown that SU(2) QCD admits an dual Abelian-Higgs phase, with a Higgs vacuum of a type-Ⅱ superconductor. This is done by using a connection decomposition for the gluon field and the random-direction approximation. Using a bag picture with soft wall, we presented a calculational procedure for the glueball energy based on the recent proof for wall-vortices [Nucl. Phys. B 741(2006)1].     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Signal generation in an isotropic medium in scanning electron acoustic microscope

Based on the research in Ref. [5][Materials Science and Engineering, 1989; A122： 57 63], an improved model of heat source is set up, the different modes of Lamb wave in an isotropic sample generated by a chopped electron beam at frequency f are obtained with integral transform and normal function expansion method, and the output signal of PZT coupled at the back surface of the sample is found out. The generation mechanism of SEAM （Scanning Electron Acoustic Microscopy） signal is discussed. It shows that the SEAM is a near field imaging technique with high spatial resolution and its best lateral spatial resolution is about 2√2α （α is the radius of the focused electron beam）. Some of experimental results of SEAM images are presented in the paper and it shows that the spatial resolution of SEAM is better than 0.5 μm and smaller than the thermal diffusion length of the sample. Therefore the character of near field imaging in SEAM is also proved experimentally.     

High efficiency filtering using two-dimensional photonic crystal coupled cavity structures

Transmission spectra of coupled cavity structures (CCSs) in two-dimensional (2D) photonic crystals (PCs) are investigated using a coupled mode theory, and an optical filter based on CCS is proposed. The performance of the filter is investigated using finite-difference time-domain (FDTD) method, and the results show that within a very short coupling distance of about 3λ, where λ is the wavelength of signal in vacuum, the incident signals with different frequencies are separated into different channels with a contrast ratio of 20 dB. The advantages of this kind of filter are small size and easily tunable operation frequencies.