不同氧气含量下镍铬系平板集热器选择性吸收薄膜的制备和性能表征

采用双极脉冲磁控溅射系统,在不同氧气含量的氩氧混合气体中制备了单层镍-铬金属-电介质复合光谱选择性吸收薄膜。采用X射线衍射仪（XRD）、激光共焦显微拉曼光谱仪、椭偏仪和紫外-可见-近红外分光光度计分别对薄膜的物相结构和光学特性进行了表征。结果表明：实验获得了由金属镍和镍、铬的氧化物（NiO、Cr₂O₃）组成的复合膜,薄膜对300~1 200 nm波段的太阳光有较强的吸收,而对波长大于1 200 nm的太阳光则吸收较弱,具有良好的光谱选择性,可用作高效太阳光谱选择性吸收涂层。     

TiO_2/Eu~(3+)下转换薄膜的制备及其在染料敏化太阳能电池中的应用

采用溶胶-凝胶法制备了TiO2/Eu3+下转换薄膜,并对其光学特性和光电性能进行了分析。将其应用到染料敏化太阳能电池(DSSC)中,利用其下转换特性将部分紫外光转换为能被染料吸收利用的可见光,提高了DSSC的光照强度,促进了短路电流的增大。荧光光谱显示,下转换薄膜在受到394 nm紫外光照射时可发射出550~640 nm的可见光,具有下转换功能特性。下转换薄膜可以增加电池对太阳光的吸收范围,当涂有二层下转换薄膜时,短路电流密度从8.05 mA·cm-2提高到9.62 mA·cm-2,光电转换效率从3.67%提高到4.32%,转换效率相对提高了17.7%。     

基于激光诱导击穿光谱技术定量分析食用明胶中的铬元素

利用激光诱导击穿光谱技术对食用明胶样品中的铬元素进行定量分析.采用Nd:YAG脉冲激光器三倍频输出的355 nm激光诱导击穿食用明胶产生激光等离子体,测量等离子发射光谱.实验数据表明:使用内标法定量分析食用明胶样品中铬元素浓度分别为10—200 ppm(1 ppm=10-6)时,铬元素含量与分析谱线(CrI:245.43 nm)强度之间具有很好的线性关系.分析了光谱探测延迟时间对明胶中铬元素激光诱导击穿光谱的影响,利用信号强度与信噪比获得了优化的光谱探测延迟时间实验参数.     

应力对La0.83Sr0.17MnO3薄膜输运性能的影响

采用溶胶-凝胶方法在Si(111)上制备了LSMO(x=0.17)薄膜.研究了块体材料和不同厚度薄膜R -T曲线、红外光谱和X射线衍射.结果表明，LSMO薄膜属于正交晶体结构，薄膜取向与膜厚度 有关，当膜厚度为450nm或680nm时，主要取向〈200〉，而膜厚度为900nm时取向为〈020〉 ：根据离子对相互作用能和谐振子模型，得到了红外吸收与Mn—O—Mn键长和键角关系式，6 00cm^-1附近红外吸收与晶格常数b的变化有关；块体与薄膜的金属—绝缘体转变 温度(T_MI)存在较大差别，薄膜转变温度显著低于块体，并与厚度有一定关系. 认为是LSMO薄膜中的应力诱导了晶格常数变化，引起键角改变及JT效应是转变温度变化的主 要原因. 关键词： 单晶硅 晶格常数 金属—绝缘体转变温度 应力诱导     

新型氟代三苯胺衍生物的合成和光谱特性研究

设计和合成了一种新型氟代三苯胺衍生物——N,N,N′,N′-四苯基-[2′,2″,3′,3″,5′,5″,6′,6″-八氟对四联苯]-4,4″′-二胺(OFTPA)。通过元素分析、熔点测定、红外光谱和1 H NMR谱等手段对OFTPA的分子结构进行了表征,并对其主要的红外光谱吸收峰和1 H NMR谱带进行了归属分析。利用紫外-可见吸收光谱、荧光光谱和循环伏安法(CV)对OFTPA的电子能级结构和发光性能进行了研究。紫外-可见吸收光谱测定结果表明,OFTPA薄膜的最大吸收峰波长为355nm,光学带隙(Eg)为3.09eV。荧光光谱测定结果表明,OFTPA薄膜在365nm紫外光的激发下,产生发光峰波长在448nm附近、半峰宽(FWHM)为68nm的蓝光发射,色纯度高,有望成为优良的蓝光发射材料。循环伏安法测定结果表明,OFTPA的最高占有轨道(HOMO)能级为-5.41eV,最低空轨道(LUMO)能级为-2.32eV,具有良好的空穴传输性能。研究结果为进一步研究其在有机光电器件中的应用提供了参考。     

纳米表面二维周期半圆凹槽增强硅薄膜太阳能电池光吸收

利用时域有限差分方法, 研究硅薄膜上下表面周期半圆凹槽结构对于太阳光吸收的增强效应. 研究发现这种结构可以实现太阳光宽波段的光吸收增强, 通过调节SiO₂表面减反层厚度和凹槽半径长度来实现薄膜太阳能电池最大的光吸收, 并实现了波长在300-1000 nm范围的太阳光吸收总能量比没有这种 结构下硅薄膜光吸收提高了约117%. 关键词： 硅薄膜 半圆凹槽 吸收增强     

基于透射光谱确定溶胶凝胶ZrO2薄膜的光学常数

基于溶胶凝胶ZrO2薄膜的紫外/可见/近红外透射实验光谱,采用Swanepoel方法结合Wemple-DiDomenico色散模型,方便地导出了ZrO2薄膜在200-1200 nm波长范围内的光学常数,包括折射率、色散常数、膜层厚度、吸收系数及能量带隙.研究发现,溶胶凝胶ZrO2薄膜具有高折射率(1.63-1.93,测试波长为632.8 nm)、低吸收和直接能量带隙(4.97-5.63 eV) 等光学特性,而且其光学常数对薄膜制备过程中的重要工艺参数--膜层后处理温度表现出强烈的依赖性.此外,在膜层的弱吸收和中等吸收光谱区域内,计算得到的折射率色散曲线与分光光度法的测试结果基本符合,说明本实验中所建立的计算方法在确定溶胶凝胶ZrO2薄膜光学常数方面的可靠性.     

纳米Cu_2O薄膜的制备及其表面增强拉曼光谱EI北大核心CSCD

采用真空电子束蒸发技术及后续热氧化技术,在玻璃基底上制备了不同厚度的金属铜薄膜。采用X射线衍射、X射线光电子能谱分别表征了所制备的金属铜薄膜的晶体结构和元素组成。采用紫外-可见-近红外分光光度计及拉曼光谱仪分别分析了所制备的金属铜薄膜的吸收谱和表面增强拉曼光谱(SERS)活性。随着膜厚的增加,退火后的薄膜样品由非晶态转变为(111)面择优生长的多晶态,且其吸收边发生红移。当退火温度为200℃、退火时间为60min时,能够获得单一相的纳米氧化亚铜(Cu_2O)薄膜。薄膜样品SERS活性随纳米Cu_2O薄膜吸光度的增大而增强。     

Na_5[B_2P_3O_(13)]晶体的紫外-远红外光谱分析

为了探索硼磷酸钠(Na_5[B_2P_3O_(13)],NBP)晶体可能具有的功能特性,发展适用不同光谱范围的硼磷酸盐材料,对其紫外-远红外光谱以及拉曼光谱进行了研究。实验测量了室温下NBP晶体在200～2 000 nm的紫外-可见-近红外透射和反射光谱、50～4 000 cm~(-1)远红外透射光谱以及拉曼光谱。首先根据光学常数间的关系,计算得到吸收系数、消光系数和折射率,并对计算得到的折射率采用Sellmeier方程进行拟合。然后分析由紫外到远红外的宽频透射光谱,最后对晶体的拉曼振动峰进行了指认。研究结果表明:在200～2 000 nm波长范围内最大吸收系数为3.1 cm~(-1),消光系数数量级为10~(-6),折射率在1.56～1.80之间,得到Sellmeier方程。在105～120 THz和150～375 THz频率范围内晶体透射率大于80%,在1.5～71 THz的声子吸收带的透射率几乎为零。晶体可作为某些波段的光学窗口材料或者特定波段的滤波器。     

纳米Cu_2O薄膜的制备及其表面增强拉曼光谱

采用真空电子束蒸发技术及后续热氧化技术,在玻璃基底上制备了不同厚度的金属铜薄膜。采用X射线衍射、X射线光电子能谱分别表征了所制备的金属铜薄膜的晶体结构和元素组成。采用紫外-可见-近红外分光光度计及拉曼光谱仪分别分析了所制备的金属铜薄膜的吸收谱和表面增强拉曼光谱(SERS)活性。随着膜厚的增加,退火后的薄膜样品由非晶态转变为(111)面择优生长的多晶态,且其吸收边发生红移。当退火温度为200℃、退火时间为60min时,能够获得单一相的纳米氧化亚铜(Cu_2O)薄膜。薄膜样品SERS活性随纳米Cu_2O薄膜吸光度的增大而增强。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.