射频离子源离子束成分光谱测量

为HL-2A装置中性束注入器研制了引出束功率为1MW的射频离子源。在测试平台上,实验离子源已经成功引出了束能量和束电流分别为35ke V和12.4A、束质子比为79%、脉宽为100ms的氢离子束,达到了设计束功率要求的44%。在射频离子源实验平台上,利用多普勒频移光谱方法测量了离子源引出束流成分比例,对比了束流成分和射频离子源引出束流之间的关系。实验数据分析表明,在10A引出束流的情况下,离子流成分H+1、H+2和H+3分别为75%、18%和7%。并且当引出束流从3.3A升至10.4A时,H+1从37%升至78%,而H+3则从19%降至9%。     

射频离子源离子束成分光谱测量

为HL-2A 装置中性束注入器研制了引出束功率为1MW 的射频离子源。在测试平台上,实验离子源已经成功引出了束能量和束电流分别为35keV 和12.4A、束质子比为79%、脉宽为100ms 的氢离子束,达到了设计束功率要求的44%。在射频离子源实验平台上,利用多普勒频移光谱方法测量了离子源引出束流成分比例,对比了束流成分和射频离子源引出束流之间的关系。实验数据分析表明,在10A 引出束流的情况下,离子流成分 H⁺ ₁、H⁺ ₂ 和H⁺ ₃ 分别为75%、18%和7%。并且当引出束流从3.3A 升至10.4A 时,H⁺ ₁ 从37%升至78%,而H⁺ ₃ 则从19%降至9%。     

60kV离子源引出与加速系统的数值模拟

对 6 0kV、70A、2s离子源的四电极引出 加速系统进行了数值模拟。利用数值计算结果对系统进行了优化。在离子流密度为 0 2 4A·cm- 2 (束中H+ 1∶H+ 2 ∶H+ 3=0 .7∶0 .2∶0 .1)和离子源等离子体离子温度为 1eV时 ,由系统栅缝出射的束最大散角小于 1o。     

大功率多磁极会切场离子源的弧放电特性分析

为了在HL-2A上实现3MW的中性束注入,我院自主研制了直径为260ram,高度为240ram的大功率多磁极会切场离子源.目前,它的性能已达到并超过了最初设计指标,放电脉冲为ls时,最大离子流密度为0.44A/cm2;放电脉冲为3s时,等离子体离子流密度0.24A/cin2;等离子体非均匀性都在5%-7%范围之内.目?它是我国国内等离子体密度最高,放电功率最大的长脉冲桶式离子源.本文通过实验数据与理论相结合的方式对弧放电特性进行分析.     

大功率多磁极会切场离子源的弧放电特性分析

为了在HL-2A上实现3MW的中性束注入, 我院自主研制了直径为260mm, 高度为240mm的大功率多磁极会切场离子源. 目前, 它的性能已达到并超过了最初设计指标, 放电脉冲为1s时, 最大离子流密度为0.44A/cm²; 放电脉冲为3s时, 等离子体离子流密度0.24A/cm²; 等离子体非均匀性都在5%—7%范围之内. 目前, 它是我国国内等离子体密度最高, 放电功率最大的长脉冲桶式离子源. 本文通过实验数据与理论相结合的方式对弧放电特性进行分析.     

外腔两束光纤激光频谱组束的实验研究

报道了外腔2个大模面积双包层Er3+/Yb3+共掺光纤激光器频谱组束的实验结果,获得了最大功率为0.80 W、组束效率高达82.5%的组束激光输出。演示和分析了光纤末端放置位置的改变、光栅的旋转对输出光谱和组束效率的影响,结果表明:当光纤末端距系统轴的位置超过某一定值时,输出光谱呈现多模;当光栅与水平面所成角度减小时,组束效率逐渐增大。     

HL-2A中性束大功率离子源的研制

2007年3月,为HL-2A中性束注入器研制的大功率离子源在核工业西南物理研究院成功通过了测试.该离子源为圆柱结构的桶式离子源型;加速器采用三电极的加减速系统.实验运行参数如下:灯丝加热电流1100A,电压12V,弧放电电压120V,弧放电电流1050A,等离子体密度达2.5×1012/cm3,离子流密度0.44A/cm2;在距等离子体电极5mm的平面上,等离子体的均匀性好于5%,工作脉宽2s.离子源物理设计、工程考虑、实验研究结果等将在本文介绍.     

Eu~(2+),Cr~(3+)共掺杂SrAl_(12)O_(19)发光体的发光性质及能量传递

采用高温固相法制备了Eu2+,Cr3+单掺杂及共掺杂的SrAl12O19发光体,研究了它的发光性质和能量传递动力学过程。Eu2+的5d→4f发射峰位于400 nm,与Cr3+位于350~450 nm波长范围的4A2→4T1的吸收带有显著的光谱重叠,有利于Eu2+→Cr3+的能量传递发生,从而将来自于Eu2+离子的紫光转换为Cr3+的深红光发射。在共掺杂的样品中,当激发Eu2+时观察到Cr3+离子的2E→4A2红色线谱发射。当监测该红色线谱发射时,激发光谱中包含有Eu2+的吸收,证明了在SrAl12O19体系中Eu2+→Cr3+能量传递的存在。能量传递导致Eu2+的荧光寿命随Cr3+浓度的增加而缩短,计算表明能量传递效率随Cr3+浓度增加而提高,当Cr3+浓度为5%时能量传递效率可达到50%。     

N_2-H_2容性耦合等离子体电非对称效应的particle-in-cell/Monte Carlo模拟

H_2-N_2混合气体电容性耦合射频放电在有机低介电系数材料刻蚀中具潜在研究意义.采用paxticle-incell/Monte Carlo模型模拟了双频(13.56 MHz/27.12 MHz)电压源分别接在结构对称的两个电极上的H_2-N_2容性耦合等离子体特征,研究了其电非对称效应.模拟结果表明,通过调节两谐波间的相位角θ,可以改变其电场、等离子体密度、离子流密度的轴向分布及离子轰击电极的能量分布.当相位角θ为0°时,低频电极(晶片)附近主要离子(H_3~+)的密度最小,离子(H_3~+,H_2~+,H~+)轰击低频电极的流密度及平均能量最高;当θ从0°变化90°时,低频电极的自偏压从-103V到106V近似线性增加,轰击电极的离子流密度变化约±18%,H~+离子轰击低频电极的最大能量约减小2.5倍,轰击电极的平均能量约变化2倍,表明氢离子能量和离子流几乎能独立控制.     

Er^3+,Cr^3+共掺杂BaAl2Si2O8荧光粉的发光性质及能量传递

利用高温固相法合成BaAl2Si2O8:Cr^3+,Er^3+系列荧光粉,研究了Cr^3+和Er^3+掺杂对BaAl2Si2O8材料发光特性的影响.BaAl2Si2O8:Er^3+荧光样品在393 nm激发波长下只呈现出峰值为550 nm的绿色荧光,来源于2H11/2→4I15/2和4S3/2→4I15/2跃迁的叠加.BaAl2Si2O8:Cr^3+荧光样品在550 nm激发波长下呈现峰值为694 nm的红色荧光,来源于2E→4A2的跃迁.在共掺杂样品BaAl2Si2O8:Cr^3+,Er^3+中,用Cr^3+激发峰的凹槽处380 nm作为激发光,得到的发射峰不仅有Er^3+的发射峰位,还有Cr^3+的发射峰位,说明两个离子之间可能存在辐射能量传递;对共掺杂BaAl2Si2O8:1%Cr^3+,x%Er^3+样品的荧光光谱进行测试,随着x的增加,Cr^3+的激发和发射光谱强度均有所增加,并且当x=0.5时,光谱强度是原来的4倍.另外,当固定Cr^3+的浓度时,随着Er^3+的浓度增加,Cr^3+的荧光寿命逐渐增加;当固定Er^3+的浓度时,随着Cr^3+的浓度增加,Er^3+的荧光寿命逐渐减小.这些现象表明了Er^3+和Cr^3+之间存在共振能量传递,通过理论计算得到Er^3+和Cr^3+之间的能量临界距离为4.5 nm,属于电偶极-电偶极相互作用.     

含氢电极脉冲放电等离子体特性诊断

利用飞行时间质谱法诊断了含氢电极脉冲真空弧离子源放电等离子体成分、离子电荷状态及离子扩散速度等特性.实验结果表明,含氢电极脉冲真空弧离子源放电等离子体的离子成分主要由H+,Ti+,Ti2+和Ti3+组成,其中Ti2+占主要部分.当放电电流为40～80 A时,Ti离子的平均电荷数在1.95～2.13之间,随着放电电流的增...     

Residence time of metal ions generated from microsecond vacuum arcs

Vacuum gaps of 1 mm with lead or copper cathode are fired by a 13 μs duration sinusoidal arc or a 10 μs duration exponentially-decaying arc, and time-of-flight (TOF) ion measurements are made at variable times after the arc ignition. At the lead cathode, Pb⁺ and Pb⁺⁺ ions are generated and the upper limit on the times for Pb⁺ ion detection are 48 μs and 46 μs from the arc ignition for the sinusoidal and exponential arcs, respectively. At the copper cathode, Cu⁺, Cu⁺⁺, and Cu⁺⁺⁺ ions are generated and detected within 15 μs and 13 μs from the arc ignition for the sinusoidal and exponential arcs, respectively. The residence time of the Pb⁺ ions in the ion acceleration region is approximately 35 μs, regardless of the waveform of the arc current. The residence time of the copper ions, described by the time constant of the time-of-flight ion current delay characteristics, is 3 μs     

Macroparticle filtering of high-current vacuum arc plasmas

The transport of vacuum arc plasmas through a 90° curved magnetic macroparticle filter was investigated using a high-current pulsed arc source with a carbon cathode. The peak arc current was in the kiloampere range, exceeding considerably the level of what has been reported in the literature. The main question investigated was whether magnetic macroparticle filters could be scaled up while maintaining the transport efficiency of small filters. In front of the cathode, we found that arc current dependent total ion saturation currents were in the range from 10% to 23% of the arc current. The best relative transmission was 25% (time integrated output/time integrated input) at a duct wall bias of 12.5 V and at an axial magnetic field of about 100 mT. The measured relative transmission of the used high-current arrangement is comparable to what has been observed with other low-current filters. The absolute measurable ion saturation currents at the filter exit reached 70 A at an arc current of about 1000 A     

单粒子态ECR离子源

介绍了一台2.45GHz电子回旋共振(ECR)单电荷离子源的磁场场形,以及它和总束流的关系.并且比较了国际上现有的几台同类型离子源的磁场场形.由此得出了关于2.45GHzECR离子源磁场场形的一些结论.     

Ion emission from arc discharge plasmas

Results are presented from studies of the ion-emission properties of the anode plasmas of low-pressure contracted arc discharges and vacuum arcs. It is shown that creating a longitudinal magnetic field in the anode region of a discharge changes the plasma parameters significantly and facilitates a large increase in the ion current. Space charge limited ion current in a vacuum arc leads to a reduction in the noise level of the total ion current and of its components with charges of up to +3, while creating Penning discharge conditions ensures that ions of different gases can be generated in this discharge system at fractions as high as 90%, depending on the type of plasma forming gas.Institute of High-Current Electronics, Siberian Branch, Russian Academy of Sciences. Translated from Izvestiya Vuzov, Fizika, No. 3, pp. 24–33, March, 1994.     

Charge state and residence time of metal ions generated from amicrosecond vacuum arc

Metal ions generated from a microsecond vacuum arc were measured using a time-of-flight (TOF) method. A point-plane vacuum gap was fired by an impulse voltage to generate metal ions. The risetime and time constant for the decay of the arc current were 0.1 and 4.5 μs, respectively. TOF ion currents were measured for variable ion extraction times after the arc ignition. At a lead cathode, Pb⁺ and Pb ⁺⁺ ions were detected for ion extraction times less than 45 μs. The average charge-state fractions of the Pb⁺ and Pb ⁺⁺ ions were 91 and 9%, respectively. At a copper cathode, Cu ⁺, Cu⁺⁺, and Cu⁺⁺⁺ ions were detected for ion-extraction times less than 12.5 μs, and the average charge-state fractions were 42, 41, and 17%, respectively. The residence times of the generated lead and copper ions were also discussed     

Angular distribution of ion current emerging from an aperture anodein a vacuum arc

The ion current distribution emerging from a vacuum arc between a Cu cathode and a conical ring anode was measured by a set of five probes. It was found that: (1) the total ion current emerging through the anode was 8.5% of the arc current; (2) the measured ion distribution without a magnetic field was a slightly flattened cosinusoidal function; (3) with an axial magnetic field, the ion current distribution became peaked along the z axis; (4) the total ion current extracted through the anode aperture slightly increased with the magnetic field; and (5) an anode with a larger aperture exhibited less magnetic collimation     

Penning阱存储离子的高分辨分析

根据Penning阱中存储和探测离子的原理,研究改善离子谱分辨率的有效措施,发现离子谱的分辨率与LC振荡回路的Q值、阱中离子的密度及LC回路的谐振频率等因素有关.实验中,谐振频率为480千赫兹,Q在120左右,电子束流在40微安左右,真空度合适时,得到了较高分辨率的离子谱.最后对离子谱进行了辨认,离子分别是H+3,H+5,H+6,H+7.     

5MW中性束弧电源DC/DC变换器的设计与实现

中性束离子源弧放电具有气体放电等离子体的非线性特性,工作时还会受到气体压强、外磁场、阴极状态等因素的影响,采用晶闸管相控调压技术的弧电源很难实现对这种大功率电弧的稳定的闭环控制。为此,提出了一种多相多重的大电流DC/DC变换器,具有响应速度快、电流上升时间短、电流纹波小等特点,大幅提高了离子源弧放电闭环控制的稳定性。设计了滤波电感能量回馈电路,弧电源可以根据中性束系统的需要使弧电流快速减小0%~100%(可调),然后根据控制信号迅速恢复正常弧电流输出,形成一个弧电流凹坑。电源还采用超级电容储能技术,使电源体积减小了2/3,电网容量小于10kV·A。离子源放电时不会受到电网波动的影响,弧放电更加稳定。实验数据显示:该电源最大输出为220kW/1500A,电流纹波在1%以内,电流上升时间约100μs,最大超调量小于3%,可以满足5 MW中性束离子源及系统的要求。     

Pressure dependence of plasma parameters in medium-vacuum nitrogenarc discharge with the titanium cathode

The plasma properties of a medium-vacuum nitrogen arc discharge from a titanium cathode were studied. The arc chamber use was 400 mm in diameter and 600 mm in length. The cathode diameter and thickness were 64 and 25 mm, respectively. The experimental conditions are given as follows: pressure range=1×10^-3~2×10^-1 torr; N₂ gas flow rate=6 ml/min; arc current=50 A. Electric probe characteristics are measured as a function of pressure and distance from the cathode surface. The analytical results obtained show that the electron energy distribution takes 1-Mx at pressures above 1×10^-2 torr but 2-Mx at pressures under 4×10^-2 torr and that the electron density has a maximum value at a certain pressure. The Ti⁺, Ti⁺⁺, and N ⁺₂ ion spectral intensities are measured as a function of pressure and distance from the cathode surface. On comparison of these results and the electron density, the Ti⁺ spectral intensity turns out to be proportional to that of the electron density. This suggests that the major ion in the plasma volume is of the Ti⁺ species