接触缺陷的振动调制超声导波检测技术研究

针对常规线性超声检测方法无法实现板结构接触类缺陷(如微裂纹、脱粘等)检测问题,将超声导波技术与振动声调制技术相结合,利用稀疏分布传感器发展了一种板结构中接触缺陷非线性超声检测方法。通过低频振动改变缺陷的接触状况,使得通过接触面的高频导波信号的相位和幅值受到调制。对受低频振动调制的超声导波二维时间序列进行时频分析,由于接触类缺陷的存在,在振动调制超声导波序列的时频分布上出现明显的低频振动频率分量。利用提取出的低频振动频率下的超声导波信号,进行了结构接触缺陷成像处理。检测试验表明,基于振动声调制的超声导波缺陷成像方法可以实现结构中的接触类缺陷检测。      

基于时频分布的盲信号分离方法研究长骨中的多模式导波信号

由于超声导波对长骨皮质骨的材料特性及厚度变化非常敏感,因此用导波评价长骨状况的研究已成为近年来的一个研究热点.在接收到的导波中,往往多种模式混叠在一起,使得进一步求取每种导波模式的群速度等与骨质状况密切相关的参数时遇到困难.本文采用基于时频分布的盲信号分离(TFBSS)方法对长骨中混叠的多模式进行分离,然后对分离后的单...     

超声轴向传播技术评价长骨的研究

用超声轴向传播技术评价长骨状况已成为近年来的一个研究热点。本文首先介绍了第一到达波(FAS)法、超声Lamb波及柱面导波法在评价长骨皮质骨状况方面的研究进展,最后分析和讨论了当前研究中存在的问题及应该研究的方向。     

时频方法分析长骨中的超声导波及皮质骨厚度

超声导波在长骨中传播时,接收信号中含有相互叠加的多个导波模式。本文提出将希尔伯特-黄变换(HHT)用于分析叠加的多模式导波信号,将其分解成许多单个独立的模式,然后对分解出的模式求得其对应频率下的群速度,并与短时傅里叶变换所得的结果进行比较。通过与理论计算结果比较,可得到长骨皮质骨的厚度。研究结果表明,实验得到的厚度与实际厚度一致。说明通过测量导波模式的速度可以评价皮质骨的厚度,也说明HHT方法是一种识别叠加多模式导波信号的有效方法。      

基于弹性模量检测骨疲劳的超声导波方法研究

研究早期诊断骨疲劳的方法是当前骨质评价方面的研究热点之一. 本文对不同弹性模量下长骨中超声导波的传播特性进行了理论分析和仿真研究.首先, 通过数值计算得到导波在管状长骨中的理论解析解.然后对管状长骨进行了时域有限差分(FDTD) 仿真, 并验证了它与理论解析解的一致性, 同时得到长骨中不同模式导波群速度、 中心频率和衰减与弹性模量的关系.研究结果表明各个导波模式的群速度和中心频率均随弹性模量的增加而增加, 而衰减随弹性模量的增加而减小.说明超声导波的传播特性参量可以反映长骨弹性模量的变化, 从而为长骨的早期疲劳诊断提供理论依据.     

矩形封闭声腔壁板轻量化对声固耦合特性的影响

基于模态耦合法建立了考虑对侧柔性壁板的矩形封闭腔体声固耦合模型,导出了耦合系统声振响应随柔性板材料属性及厚度变化的近似关系.通过数值仿真计算,详细分析了单柔性板-单侧激励、双柔性板-双侧激励及双柔性板-单侧激励三种情况下板的轻量化设计对系统声固耦合特性及腔内声压响应的影响.结果表明:对于单柔性板-单侧激励及双柔性板-双侧激励情况,低频段腔内声压主要取决于板厚,其次是杨氏模量,而与板密度关系较弱.因此使用适当增厚的轻质板可以同时达到减重和低频区降噪的目标.对于双柔性板-单侧激励情况,适当的轻量化设计可以显著增强两板间低频段振动的耦合,从而降低该频段的声腔模态响应及腔内噪音.在中高频段,增加板厚和材料密度对降低三种情况的腔内声压均有利。      

应崇福院士90生辰学术报告会论文超声检测用压电换能器瞬态特性可控可调

超声检测用压电换能器瞬态特性主要包括瞬态空间响应和瞬态时间响应.本文通过调整控制换能器和激励源,实现瞬态空间响应和瞬态时间响应的某些特性的可控可调.其中包括在空间响应方面消除边缘波以获得平行声束和消除平面波以获得聚焦绳声束;在时间响应方面,调整换能器的背衬阻抗以获得可调首次波幅比和调整换能器结构和激励电信号以获得任意检测信号等.     

Barker码激励超声导波在长骨检测中的应用

单脉冲激励的超声导波在长骨中传播时,信号的衰减大,导致接收信号的幅度很小,且噪声严重。Barker码激励能有效增大接收信号幅度,提高信噪比(SNR)。将其应用到超声导波长骨检测中,进行仿真和长骨实验,得到的信号分别用加权匹配滤波器和有限冲激响应-最小均方误差(FIR-LS)逆滤波器进行压缩,并与单脉冲激励的结果进行了对比。结果表明,对于13位的Barker码,采用加权匹配滤波器进行解码时,压缩信号幅度是单脉冲激励接收信号的13倍;而FIR-LS逆滤波器则达到-63.59 dB的峰值旁瓣水平(PSL),更好地抑制噪声。说明可以将Barker码激励超声导波应用于长骨的检测中。      

超声检测用压电换能器瞬态特性可控可调

超声检测用压电换能器瞬态特性主要包括瞬态空间响应和瞬态时间响应。本文通过调整控制换能器和激励源,实现瞬态空间响应和瞬态时间响应的某些特性的可控可调。其中包括在空间响应方面消除边缘波以获得平行声束和消除平面波以获得聚焦绳声束;在时间响应方面,调整换能器的背衬阻抗以获得可调首次波幅比和调整换能器结构和激励电信号以获得任意检测信号等。     

适用于任意形状封闭空间的声场预测相干模型

针对现有几何声学的方法对封闭空间内声场进行预测时在中低频段出现较大误差的问题,该文提出一种近似圆锥声束追踪法和相干反射场理论相结合的声场预测新模型。在近似圆锥声束追踪法基础上,考虑声束轴线在边界多次反射时声压和相位的改变,最后计算不同声波之间的干涉效应,建立一种适用于任意形状封闭空间的声场预测相干模型。利用该模型对某一矩形封闭空间进行声场预测,通过对边界元法、Raynoise软件相干和非相干算法的预测结果和本模型的数值模拟结果对比。结果表明,文中提出的方法和边界元法的计算结果在中低频段非常吻合,两者的计算结果平均绝对误差为1.1 d B。本模型在中低频率下与同样考虑了相位的Raynoise相干算法相比有更好的准确性,在较高频率上,本模型计算结果与Raynoise相干算法计算结果非常吻合。     

套管中模式波的响应特征*

在固井质量评价中主要利用套管中模式波的幅度或衰减变化反映水泥的胶结状况,不同测井仪器在套管中激发的模式波的类型不同,研究套管中各模式波的传播特征和影响因素可充分挖掘测量数据的潜在应用价值。CBL和SBT等测井仪器在套管中主要激发拉伸波,类同于平板中的零阶对称Lamb波,水泥环封隔测井仪器的斜入射模式在套管中主要激发套管弯曲波,类同于平板中的零阶反对称Lamb波,垂直入射模式激发套管共振波,类同于平板中的高阶对称Lamb波。该文重点分析了这些模式波的衰减特征及其对微环的响应,套管弯曲波在套后耦合轻质水泥时对微环不敏感,但在套后耦合常规水泥或重水泥时,其衰减明显高于胶结良好的状况;拉伸波对微环的存在最为敏感;套管共振波对微环不敏感。     

Acousto-optic study of the unusual cases of reflection of bulk elastic waves in a paratellurite crystal

The propagation and reflection of bulk ultrasonic waves in a paratellurite crystal have been investigated by the acousto-optic method. Simultaneous excitation of two acoustic waves by one piezoelectric transducer has been observed in a cell of complex, specially chosen configuration. Maximally efficient conversion of the energy of a quasi-longitudinal wave into a single reflected quasi-shear wave with a walkoff angle 72° is implemented for the reflection from a free crystal boundary. The wave beam compression by a factor of 7 is observed for this reflection. A reflection (close to backward) of waves with an angle of spatial separation of the incident and reflected beams equal to 8° is also implemented. The acousto-optic figure of merit values of the medium are calculated for arbitrary propagation and polarization directions of the interacting light and ultrasonic waves. Possible applications of the effects studied in acousto-optics and acoustoelectronics are indicated.     

Structural waveguide behaviour of a beam–plate system

Structures which have a constant cross-section normal to a longitudinal axis can be considered as waveguides in which vibration can propagate in the form of various waves in the longitudinal direction. The dynamic behaviour of such systems can be found by using a Fourier transform approach in terms of wavenumbers in the longitudinal direction. Analytical solutions are available for simple, infinitely long waveguides, whereas for more complex waveguides numerical approaches have been developed using finite element techniques to describe the cross-section. In the present paper an analytical Fourier transform approach is used to find the dynamic behaviour of a system consisting of two parallel beams coupled by a plate, when a point force is applied to one of the beams. Multiple waves occur in the longitudinal direction, the number of waves depending on the number of modes of the equivalent cross-section. However, the motion of the driven beam is shown to be dominated by the contribution from only one or two waves at each frequency, these having wavenumbers closest to that of the uncoupled beam. The motion of the plate is also shown to be dominated by these wavenumbers for excitation on the beam. Experimental results are obtained on beam–plate–beam systems with identical and non-identical beams, which show good agreement with the predictions. In particular, these confirm that the plate response is dominated by waves with wavenumbers in the beam direction that follow those of the excited beam.     

Wave phase conjugation of the stokes component of Brillouin scattering of ultrasound

Wave phase conjugation of a low-frequency ultrasonic wave due to Brillouin scattering of high-frequency parametrically phase conjugate waves in liquid was theoretically and experimentally studied. It was shown that the envelope of the low-frequency conjugate wave is proportional to the product of envelopes of high-frequency waves. The conjugation efficiency corresponds to the angular diagram of the resonant interaction of ultrasonic beams. Compensation for the phase shift of the plane low-frequency wave due to its wave phase conjugation was demonstrated.     

Three-dimensional finite element modeling of guided ultrasound wave propagation in intact and healing long bones

The use of guided waves has recently drawn significant interest in the ultrasonic characterization of bone aiming at supplementing the information provided by traditional velocity measurements. This work presents a three-dimensional finite element study of guided wave propagation in intact and healing bones. A model of the fracture callus was constructed and the healing course was simulated as a three-stage process. The dispersion of guided modes generated by a broadband 1-MHz excitation was represented in the time-frequency domain. Wave propagation in the intact bone model was first investigated and comparisons were then made with a simplified geometry using analytical dispersion curves of the tube modes. Then, the effect of callus consolidation on the propagation characteristics was examined. It was shown that the dispersion of guided waves was significantly influenced by the irregularity and anisotropy of the bone. Also, guided waves were sensitive to material and geometrical changes that take place during healing. Conversely, when the first-arriving signal at the receiver corresponded to a nondispersive lateral wave, its propagation velocity was almost unaffected by the elastic symmetry and geometry of the bone and also could not characterize the callus tissue throughout its thickness. In conclusion, guided waves can enhance the capabilities of ultrasonic evaluation.     

Flexural wave motion in beam-type disordered periodic systems: Coincidence phenomenon and sound radiation

This paper deals with flexural wave motion in uniform beam-type periodic systems whose repeating units are identical finite beams with multiple beam-length disorders. A general expression derived for the propagation constants has been employed to study its variation with frequency for a beam system having 4-span disordered repeating units. This is helpful in understanding flexural wave motion in disordered periodic beams. Free flexural waves have been studied as wave groups consisting of a large number of harmonic components of different wavelengths, phase velocities and directions. Phase velocities have been computed and plotted for different frequencies in the propagation zones in which the free waves progress without attenuation. This has been found to be useful in understanding and predicting the coincidence phenomenon in disordered periodic beams under convected pressure field loading. The excitation of wave groups in disordered periodic beam-type systems by a slow (subsonic) convecting pressure field can include fast (supersonic) moving flexural wave components which can radiate sound. It has been pointed out that sound radiation from a disordered periodic beam (or plate) can be quite different as compared to that from a periodic beam under similar convected pressure field loading.     

多通道超声兰姆波检测板状结构中的裂纹

超声兰姆(Lamb)波在结构缺陷检测方面愈来愈受到重视,但目前Lamb波的应用局限于单信号源激励,单通道接收的方法,容易受到噪声干扰,其后续的信号分析处理也比较复杂。本文旨在采用多通道Lamb波对板状结构中的裂纹进行定量分析与诊断。在铝板的表面凿刻出不同深度的凹槽作为裂纹,通过线阵换能器采集在一定传播距离内的多通道Lamb波信号,并采用二维傅里叶变换分析在不同深度的裂纹下,Lamb波模式能量的变化规律。结果表明,相对于完好铝板中的Lamb波信号,裂纹的存在会使Lamb波发生模式转换现象,并且转换模式能量百分比随裂纹深度的增加而线性增加。其结果为Lamb波评价板状结构中的裂纹状况提供了一种可能的方法。     

采用超声导波特征参量的骨质疏松识别方法

骨质的定期检测对骨质疏松的防治至关重要。本文研究了骨质疏松对超声导波在人体长骨中传播的影响。提出采用多尺度小波变换方法对接收到的导波信号进行处理,通过分析在不同传播距离下高阶小波细节分量所占信号总能量的变化,来判断是否患有骨质疏松症。在13位志愿者的小腿胫骨上进行超声测量,得到导波信号。经多尺度小波变换方法的分析处理结果显示在13位志愿者中,有7位志愿者的超声导波信号随着传播距离的改变,其主要频率成分发生了明显的变化,显示这7位志愿者患有骨质疏松症。这一诊断结果与X射线技术诊断结果相比,准确率可以达到92.3%,表明本文所提出的利用小波多尺度变换方法对长骨进行超声诊断具有较好的潜力。      

离子束-等离子体系统中的参量不稳定性

本文研究了外pump电场E_0在离子束-等离子体系统中所激发的静电低频参量不稳定性。导出了这种低频波的一般色散关系,并用数值方法分析了一维质子束-等离子体系统的参量不稳定性的激发过程。结果表明:离子束对等离子体中参量不稳定性的激发有极重要的影响。当没有离子束时,只能激发一种模式的波;一旦将离子束引入等离子体中,就可以在系统中激发两个波长较长的低频波。     

A Particle-in-Cell Simulation Study on Harmonic Waves Excited by Electron Beams in Unmagnetized Plasmas

The excitation of harmonic waves by an electron beam is studied with electrostatic simulations.The results suggest that the harmonic waves are excited during the linear stage of the simulation and are developed in the nonlinear stage.First,the Langmuir waves(LWs)are excited by the beam electrons.Then the coupling of the forward propagating LWs and beam modes will excite the second harmonic waves.The third harmonic waves will be produced if the lower velocity side of the beam still has a positive velocity gradient.The beam velocity decreases at the same time,which provides the energy for wave excitation.We find that it is difficult to excite the harmonic waves with the increase of the thermal velocity of the beam electrons.The beam electrons will be heated after waves are excited,and then the part of the forward propagating LWs will turn into electron acoustic waves under the condition with a large enough intensity of beam electrons.Moreover,the action of ions hardly affects the formation of harmonic waves.