铝板中Lamb波检测的实验研究

Lamb波在传播过程中具有频散及多模态特性,若相关参数选择不当,会导致在实际应用中信号相互叠加而无法识别。本文基于Lamb波的频散曲线是其频散方程实数解分布的特点,采用二分法绘制了铝板中Lamb波的频散曲线、波结构曲线和入射角曲线。根据曲线选择S0模态的Lamb波对1mm厚铝板中不同类型的缺陷进行检测。实验结果表明,S0模态的Lamb波对裂纹型缺陷和贯穿型缺陷十分敏感,但对于裂纹型缺陷,其幅值变化并不与缺陷大小成线性关系,并且S0模态Lamb波的声场指向性十分集中,在偏离声束轴线时无法检测到缺陷。     

板状结构Lamb波频散补偿与聚焦接收成像检测

对板状结构中Lamb波的频散和多模现象进行了理论分析,采用有限元仿真方法获取了Lamb波与缺陷作用后的回波信号,对信号进行聚焦接收处理,即在一定距离范围内利用导波频散特性对各个模式信号进行频散补偿,提取补偿后信号的幅值,结果表明当所得信号幅值最大时,所对应的补偿距离等于缺陷与换能器之间的实际距离.利用这一结论,提出了以...     

基于模态识别与分离的铝板激光超声检测

用Nd:YAG激光器在2 mm厚的铝板上激发激光超声,通过激光反射镜偏转进行点阵扫描激励,用声发射传感器接收在铝板中传播的激光超声信号,通过信号放大和数据采集得到激光超声在铝板中传播的数据。对上述数据进行二维傅里叶变换得到了铝板中激光超声的模态分布和频率分布,接收到的激光超声是S0和A0两个模态多种频率的Lamb波。利用两个相同的探头对称地压紧在板的两个表面上,对两个探头接收到的信号进行相加和相减,可以将S0和A0模态分别提取出来。对单一模态的Lamb波再进行滤波,得到了窄频带单一模态的Lamb波。采用该方法实现了从杂乱的激光超声原始信号中提取出清晰的伤信号,并且得到了不同模态在不同频率范围的检测结果。     

窄频带Lamb波频散特性研究

利用连续小波变换对从铝合金板结构中俘获的Lamb波信号进行分析,获得波信号在时间-尺度域的等高线和等高线脊线.根据Lamb波的频散特征、时间-尺度域等高线脊线的斜率和波在不同尺度下的到达时间,识别了Lamb波信号中各信息包的模式,并匹配出基础阶模式窄频带Lamb波在铝合金板结构中传播的实际频散曲线.对试验的Lamb波信号分析的结果表明该方法对于研究和应用窄频带Lamb波的频散特性是有效的. 关键词： 连续小波变换 Lamb波 频散     

声表面波检测铝板表面微缺陷深度实验研究

为了探究声表面波与不同深度微裂纹缺陷相互作用的关系,将脉冲激光作用于一系列不同缺陷的试件铝板上进行线光源激励,激发激光超声波。用超声传感器接收在铝板中传播的激光超声信号,通过数字荧光示波器采集激光超声在铝板中的传播数据。对采集到的反射波数据进行分离谱分离过程得到的铝板中激光超声的时域分布和透射波数据进行频域分析。实验发现:缺陷深度影响着反射回波两峰值特征点到达时间差,两者之间近似线性关系,也影响着透射波的截止频率且二者呈现递减关系。     

基于时间反转理论的聚焦Lamb波结构损伤成像

从理论和实验上研究了时间反转法在频散和多模式的Lamb波结构健康检测方面的应用.当Lamb波在包含有损伤的板类结构中传播时,损伤的存在表现为一个被动波源.采用分布式传感器网络,基于传递函数的观点,通过推导由损伤这个被动波源产生的时间反转波场幅值的表达式,证实了当观察点位于损伤位置时,时间反转波场的幅值最大.为验证时间反转方法的聚焦效应,提出了一种适合于分布的激励/接收传感器网络的成像方法,该方法可以对损伤定位并近似确定损伤尺寸.结合有限元的实验结果显示了Lamb波检测信号的能量可在损伤处聚焦,表明时间反转     

超声Lamb波混频激励效率与模式选择

研究了超声Lamb波混频的激励效率与模式选择。在非零能量流和相匹配条件的基础上,结合Lamb波在结构中的状态分布,提出了以激励效率参量作为超声Lamb波混频模式选择的依据。根据混频条件筛选混频模式对,计算相应的激励效率参量,并通过超声Lamb波混频的仿真模拟与实验测量进行验证。通过对比仿真与实验中得到的非线性参量与激励效率参量的关系,证明了激励效率参量作为模式选择依据的有效性。研究表明,激励效率参量可以有效地表征超声Lamb波混频的激发效率,从而筛选非线性效应明显的模式对,更好地实现损伤的检测与表征。     

压电晶片传感器监测金属薄板的腐蚀

激励压电晶片传感器产生Lamb波并用于监测金属板材的腐蚀,由信号的相关系数表征腐蚀对在板中Lamb波传播特性的影响。实验结果表明在Lamb波模态中A₀模式受腐蚀影响大,适合用于监测金属的腐蚀。Lamb波通过腐蚀区域后由于频散以及信号幅度和相位的变化对采集的损伤信号与健康状态信号的相关系数有影响。在腐蚀区域直径一定的情况下,对应的相关系数并不随腐蚀深度的增加而单调递减;在腐蚀深度一定时,相关系数随腐蚀区域直径增加而单调递减。     

Lamb波多特征参数的复合材料损伤程度 评估方法*

航空航天飞行器、风电等工程机械结构的安全性保障至关重要,复合材料等新材料的大量应用,进一步提升了对结构健康监测的难度和要求。裂纹、脱层等复合材料结构典型损伤形成机理复杂、易扩展,损伤程度累积严重时会造成结构的突然失效。面向复合材料结构的损伤监测与诊断,现有的方法大多很难实现对结构损伤程度的跟踪评估,进而无法对结构的安全性评价提供依据。采用Lamb波监测理论,基于其传播距离远、对小损伤敏感等特点,通过研究分析典型损伤对Lamb波结构响应信号传播的多个特征作用过程和机理,采用多尺度分析,提取结构损伤时频域多特征参数;借助于神经网络的非线性映射能力,构建多特征复合材料结构损伤程度评估模型,实现对不同程度下典型结构损伤的评估。在环氧玻璃纤维复合材料板结构上的实验验证结果表明：提取的Lamb波时频域多特征参数,对不同程度典型损伤有一定的敏感性,所构建的损伤程度评估系统可以较为有效的实现损伤的程度估计。     

超声导波评价长骨骨折的仿体实验研究

定量超声评价长骨骨折已成为近年来的研究热点之一,超声导波模式转换理论可被应用于长骨骨折状况的评价。采用三维时域有限差分法分析骨折长骨中导波模式转换的基本规律,提取模式转换定量评价参数;进而结合亚克力管仿体实验,分析不同裂纹程度下导波模式的转换情况。仿真与仿体实验表明,导波模式能量参数与裂纹程度具有很好的相关性,可用于评价长骨骨折状况。     

Micro-crack detection of nonlinear Lamb wave propagation in three-dimensional plates with mixed-frequency excitation

We propose a nonlinear ultrasonic technique by using the mixed-frequency signals excited Lamb waves to conduct micro-crack detection in thin plate structures. Simulation models of three-dimensional(3D) aluminum plates and composite laminates are established by ABAQUS software, where the aluminum plate contains buried crack and composite laminates comprises cohesive element whose thickness is zero to simulate delamination damage. The interactions between the S_0 mode Lamb wave and the buried micro-cracks of various dimensions are simulated by using the finite element method.Fourier frequency spectrum analysis is applied to the received time domain signal and fundamental frequency amplitudes,and sum and difference frequencies are extracted and simulated. Simulation results indicate that nonlinear Lamb waves have different sensitivities to various crack sizes. There is a positive correlation among crack length, height, and sum and difference frequency amplitudes for an aluminum plate, with both amplitudes decreasing as crack thickness increased, i.e.,nonlinear effect weakens as the micro-crack becomes thicker. The amplitudes of sum and difference frequency are positively correlated with the length and width of the zero-thickness cohesive element in the composite laminates. Furthermore,amplitude ratio change is investigated and it can be used as an effective tool to detect inner defects in thin 3D plates.     

不锈钢折弯板裂纹Lamb波检测技术*

金属弯板广泛应用于车辆、船舶、飞机等大型装备结构件中，折弯处易形成应力集中产生裂纹，直接影响构件的使用安全和寿命。本文开展了不锈钢弯板裂纹缺陷Lamb波检测技术研究，计算了钢板的频散曲线，优选三种不同频率的S0模态：0.25MHz、0.5MHz、1MHz。利用COMSOL软件建立频域仿真模型，模拟了Lamb波在3mm厚“L”形弯板内部的传播情况，开展折弯板裂纹缺陷检测实验，并使用小波包变换的方法对实验信号进行分析。结果表明，经小波变换后，0.25MHz、0.5MHz、1 MHz的S0模态Lamb波均可用于裂纹缺陷的识别检测.     

Wideband dispersion removal and mode separation of Lamb waves based on two-component laser interferometer measurement

Ultrasonic Lamb waves are considered as a sensitive and effective tool for nondestructive testing and evaluation of plate-like or pipe-like structures. The nature of multimode and dispersion causes the wave packets to spread, and the modes overlap in both time and frequency domains as they propagate through the structures. By using a two-component laser interferometer technique, in combination with a priori knowledge of the dispersion characteristics and wave structure information of Lamb wave modes, a two-component signal processing technique is presented for implementing dispersion removal and mode separation simultaneously for two modes mixture signals of Lamb waves. The proposed algorithm is first processed and verified using synthetic Lamb wave signals. Then, the two-component displacements test experiment is conducted using different aluminum plate samples. Moreover, we confirm the effectiveness and robustness of this method.     

Normal mode expansion method for laser-generated ultrasonic Lamb waves in orthotropic thin plates

A quantitative theory for modeling the laser-generated transient ultrasonic Lamb waves, which propagates along arbitrary directions in orthotropic plates, is presented by employing an expansion method of generalized Lamb wave modes. The displacement field is expressed by a summation of the symmetric and antisymmetric modes in the surface stress-free orthotropic plate, and therefore the theory is particularly appropriate for waveform analyses of Lamb waves in thin plates because one needs only to evaluate several lower modes. The transient waveforms excited by the thermoelastic expansion and the oil-coating evaporation are analyzed for a transversely isotropic thin plate. The results show that the theory provides a quantitative analysis to characterize anisotropic elastic stiffness properties of orthotropic plates by laser-generated Lamb wave detection.     

Modal decomposition method for modeling the interaction of Lamb waves with cracks

The interaction of the low-order antisymmetric (a0) and symmetric (s0) Lamb waves with vertical cracks in aluminum plates is studied. Two types of slots are considered: (a) internal crack symmetrical with respect to the middle plane of the plate and (b) opening crack. The modal decomposition method is used to predict the reflection and transmission coefficients and also the through-thickness displacement fields on both sides of slots of various heights. The model assumes strip plates and cracks, thus considering two-dimensional plane strain conditions. However, mode conversion (a0 into s0 and vice versa) that occurs for single opening cracks is considered. The energy balance is always calculated from the reflection and transmission coefficients, in order to check the validity of the results. These coefficients together with the through-thickness displacement fields are also compared to those predicted using a finite element code widely used in the past for modeling Lamb mode diffraction problems. Experiments are also made for measuring the reflection and transmission coefficients for incident a0 or s0 lamb modes on opening cracks, and compared to the numerical predictions.     

电磁超声换能器激发超声兰姆波的模式展开分析

提出一种用于研究电磁超声换能器(EM.AT)激发超声兰姆波的模式展开分析方法。从EMAT曲折线圈的电流分布出发,推导出铝板表面洛伦兹切向应力的形式解;对其进行空间傅里叶变换,得到激发超声兰姆波的表面驱动应力之波数谱密度。在此基础上采用导波激发的模式展开分析方法,推导出与EMAT线圈的几何参数密切相关的兰姆波模式展开系数的数学表达式,为严格分析EMAT的兰姆波激发问题奠定了理论基础。数值分析结果表明,通过改变EMAT线圈的几何参数,可对兰姆波的模式展开系数进行适当调整,从而实现有效抑制不需要兰姆波模式的目的,这一结果为采用EMAT激发纯度高的单一兰姆波模式提供了理论依据。      

Laser-ultrasonic generation of Lamb waves in the reaction force range

The Laser-ultrasonic generation of Lamb waves in an elastic plate is investigated theoretically and experimentally for a laser source whose intensity is high enough to create reaction forces (normal tractions) on the illuminated surface of the specimen. The analytical solutions for transient waves are derived using the integral transform method first by considering an arbitrary source shape and time excitation function, and then specifically for circular and line source shapes. The simulation study allows us not only to predict the behavior of individual wave modes but also to construct the overall responses; thus it helps us better understand the wave excitation mechanisms. The dispersive and multi-modal nature of laser-generated Lamb waves is presented by showing the spatiotemporal Fourier transform of displacements obtained by the simulation study. The transform, displayed in the frequency-wave number domain, enunciates the characteristics of the propagating individual Lamb wave modes. The simulation results are then compared with the 2-D Fourier transform of a set of experimental data obtained by scanning an aluminum plate specimen.     

套管中模式波的响应特征*

在固井质量评价中主要利用套管中模式波的幅度或衰减变化反映水泥的胶结状况,不同测井仪器在套管中激发的模式波的类型不同,研究套管中各模式波的传播特征和影响因素可充分挖掘测量数据的潜在应用价值。CBL和SBT等测井仪器在套管中主要激发拉伸波,类同于平板中的零阶对称Lamb波,水泥环封隔测井仪器的斜入射模式在套管中主要激发套管弯曲波,类同于平板中的零阶反对称Lamb波,垂直入射模式激发套管共振波,类同于平板中的高阶对称Lamb波。该文重点分析了这些模式波的衰减特征及其对微环的响应,套管弯曲波在套后耦合轻质水泥时对微环不敏感,但在套后耦合常规水泥或重水泥时,其衰减明显高于胶结良好的状况;拉伸波对微环的存在最为敏感;套管共振波对微环不敏感。     

Piezoelectric transducer parameter selection for exciting a single mode from multiple modes of Lamb waves

Excitation and propagation of Lamb waves by using rectangular and circular piezoelectric transducers surface-bonded to an isotropic plate are investigated in this work. Analytical stain wave solutions are derived for the two transducer shapes, giving the responses of these transducers in Lamb wave fields. The analytical study is supported by a numerical simulation using the finite element method. Symmetric and antisymmetric components in the wave propagation responses are inspected in detail with respect to test parameters such as the transducer geometry, the length and the excitation frequency. By placing only one piezoelectric transducer on the top or the bottom surface of the plate and weakening the strength of one mode while enhancing the strength of the other modes to find the centre frequency, with which the peak wave amplitude ratio between the S0 and A0 modes is maximum, a single mode excitation from the multiple modes of the Lamb waves can be achieved approximately. Experimental data are presented to show the validity of the analyses. The results are used to optimize the Lamb wave detection system.