基于时频分布的盲信号分离方法研究长骨中的多模式导波信号

由于超声导波对长骨皮质骨的材料特性及厚度变化非常敏感,因此用导波评价长骨状况的研究已成为近年来的一个研究热点.在接收到的导波中,往往多种模式混叠在一起,使得进一步求取每种导波模式的群速度等与骨质状况密切相关的参数时遇到困难.本文采用基于时频分布的盲信号分离(TFBSS)方法对长骨中混叠的多模式进行分离,然后对分离后的单...     

时频方法分析长骨中的超声导波及皮质骨厚度

超声导波在长骨中传播时,接收信号中含有相互叠加的多个导波模式。本文提出将希尔伯特-黄变换(HHT)用于分析叠加的多模式导波信号,将其分解成许多单个独立的模式,然后对分解出的模式求得其对应频率下的群速度,并与短时傅里叶变换所得的结果进行比较。通过与理论计算结果比较,可得到长骨皮质骨的厚度。研究结果表明,实验得到的厚度与实际厚度一致。说明通过测量导波模式的速度可以评价皮质骨的厚度,也说明HHT方法是一种识别叠加多模式导波信号的有效方法。      

骨折长骨中超声导波传播特性的仿真研究

采用超声导波评价长骨骨折已成为近两年来的一个研究热点.本文采用混合边界元方法(HBEM)对超声导波在骨裂长骨中的传播情况以及各导波模式的反射系数和透射系数进行了数值分析.研究结果表明,入射导波模式经由裂纹处模式转换后依然保持为主要接收模式不变.对某一裂纹,各模式透射系数常在相近的频率点上达到局部峰值.对于不同深宽比(d/w)裂纹,某些模式透射系数曲线局部峰值所对应的频率存在着相互错开的现象,这些结果可用于选择最优入射导波模式和频率,以便更好地定量评价骨质以及骨裂状况.     

管间界面特性对周向超声导波传播特性的影响

采用界面弹簧模型对圆管结构的管间界面特性进行描述, 推导出含弱界面的圆管结构中声波沿周向传播时的位移场及应力场的数学表达式. 在此基础上采用导波的模式展开分析方法, 给出了与管间界面特性及激励源密切相关的周向超声导波模式展开系数的解析表达式. 数值分析了管间界面特性的变化对周向超声导波的频散和声场产生的影响. 理论与数值分析结果表明, 通过选择适当的驱动频率及周向导波模式, 可使周向超声导波的相速度及圆管外表面的位移场随管间界面特性的变化表现出非常敏感且单调的性质. 这一结果有助于采用周向超声导波方法准确定征圆管结构的管间界面特性.     

超声导波评价长骨骨折的仿体实验研究

定量超声评价长骨骨折已成为近年来的研究热点之一,超声导波模式转换理论可被应用于长骨骨折状况的评价。采用三维时域有限差分法分析骨折长骨中导波模式转换的基本规律,提取模式转换定量评价参数;进而结合亚克力管仿体实验,分析不同裂纹程度下导波模式的转换情况。仿真与仿体实验表明,导波模式能量参数与裂纹程度具有很好的相关性,可用于评价长骨骨折状况。     

长骨中振动声激发超声导波的方法

为了实现一定频段内任意低频下在长骨中激励导波信号,本文提出一种采用聚焦高频(5 MHz)超声换能器在长骨皮质骨中激发低频(150 kHz)超声导波的振动声方法.首先介绍了板状超声导波理论和双声束共聚焦法与单声束调幅法激发振动声的基本原理;进而采用三维有限元仿真方法分析振动声激发低频超声导波的基本现象,然后结合牛胫骨板离体实验,验证振动声激发低频超声导波的可行性.结果均表明,双声束共焦与单声束振动超声均可在骨板中激发低频超声导波.相关研究方法有助于提高空间域长骨中超声导波测量精度,以及在一定频段内实现任意频率激励等,对发展低频超声导波在体测量长骨皮质骨的新技术具有一定的指导意义.     

曲线坐标系下孔隙介质圆柱纵向表面波的传播特性

为了研究孔隙介质圆柱纵向表面波的传播规律,分析其频散和衰减特性,在正交曲线坐标系下建立了表面波的频散方程,通过数值计算得到频散曲线,将纵向导波最低模态与表面波进行对比,并分析了曲率半径及孔隙参数对表面波频散和衰减的影响。结果表明,当频率足够大时,导波最低模态的频散曲线与表面波近似;在同一频率下,表面波的相速度随曲率半径的增大而增大,随孔隙度的增大而减小;表面波的衰减随孔隙度的增大而增大。研究结果为开展孔隙介质圆柱结构的超声无损评价提供了一定的理论参考。     

被孔隙介质约束的弹性杆中的导波*

为了研究导波在被孔隙介质约束的弹性杆结构中的传播规律,分析孔隙参数对导波传播特性的影响,本文建立了无限大孔隙介质包裹圆柱体的理论模型,利用孔隙介质弹性波动理论,分析了导波的频散曲线,以及圆柱半径和孔隙参数对于导波传播特性的影响。结果表明,在该结构中传播的纵向导波存在频散特性。内部圆柱半径的改变影响波导结构,从而影响导波传播。外部孔隙介质的渗透率对于导波频散的影响较小,孔隙度的改变影响孔隙介质体波波速,从而影响导波频散曲线的截止频率。同时,导波存在较小的衰减,且衰减随孔隙度增大而增大。这些结果对于后续开展无限大介质包裹弹性杆结构的超声无损评价提供了一定的理论参考。     

复合圆管界面特性对周向超声导波二次谐波发生效应的影响分析

研究了复合圆管的管间界面特性对周向超声导波二次谐波发生效应所产生的影响.在二阶微扰近似条件下,将周向超声导波传播过程中的非线性效应视为其线性波动响应的一个二阶微扰.采用界面弹簧模型对复合圆管的管间界面特性进行描述.根据导波的模式展开分析方法,伴随基频周向超声导波传播所发生的二次谐波可视为由一系列二倍频周向导波模式叠加而成.管间界面特性的变化可从多个方面对二倍频周向导波模式的展开系数及声场产生影响,尤其是界面特性的变化所引起的周向超声导波相速度的改变,将显著地影响到二次谐波随传播周向角的积累增长程度.理论及数值分析结果表明,周向超声导波的二次谐波发生效应随管间界面特性的改变而发生非常敏感的变化,可将其用于准确定征复合圆管的管间界面性质.     

各向异性固体板中的非线性超声导波

将超声导波的非线性视为线性波动响应的一个二阶微扰,采用二阶微扰近似和导波的模式展开分析方法,从理论上研究了各向异性固体板中超声导波的二次谐波发生效应,给出了超声导波二次谐波声场的一般形式解.板材的各向异性可从多个方面对二次谐波发生效应产生影响,尤其是板材各向异性引起的导波模式相速度的改变,可显著地影响到构成导波二次谐波声场的二倍频导波模式随传播距离的积累增长程度.根据理论分析和数值计算结果可知,在不同传播方向上超声导波的非线性效应存在较显著的差异,伴随基频导波模式的传播所发生的二次谐波对固体板材的各向异性表现出更为敏感的性质,这一结果可为准确定征板材的弹性各向异性提供一种理论依据.     

Numerical simulation of wave propagation in cancellous bone

Numerical simulation of wave propagation is performed through 31 3D volumes of trabecular bone. These volumes were reconstructed from high synchrotron microtomography experiments and are used as the input geometry in a simulation software developed in our laboratory. The simulation algorithm accounts for propagation into both the saturating fluid and bone but absorption is not taken into account. We show that 3D simulation predicts phenomena observed experimentally in trabecular bones : linear frequency dependence of attenuation, increase of attenuation and speed of sound with the bone volume fraction, negative phase velocity dispersion in most of the specimens, propagation of fast and slow wave depending on the orientation of the trabecular network compared to the direction of propagation of the ultrasound. Moreover, the predicted attenuation is in very close agreement with the experimental one measured on the same specimens. Coupling numerical simulation with real bone architecture therefore provides a powerful tool to investigate the physics of ultrasound propagation in trabecular structures.     

各向异性渗流条件下弹性波的传播特征

研究了弹性波在非均匀裂纹孔隙介质中的传播特性,建立了各向异性喷射流模型.当弹性波通过裂纹孔隙介质时,由于波的扰动及裂纹和孔隙几何结构的不一致,导致在裂纹内部及裂纹与周边孔隙之间同时存在着流体压力梯度.此时的弹性波波动响应中包含着裂纹内连通性特征和背景孔隙渗透率信息.流体的动态流动过程使得介质的等效弹性参数为复数(非完全弹性),并且具有频率依赖性.当弹性波为低频和高频极限时,介质为完全弹性;当处于中间频段时,波有衰减和频率依赖.裂纹孔隙介质的各向异性连通性(渗透率)对应着各向异性特征频率(当渗流长度等于非均匀尺度时的弹性波频率),波的传播受到裂纹内连通性的影响.在一定频段内,随着裂纹厚度的增加,将出现第二峰值,峰值大小同时受到裂纹厚度和半径的影响.     

Numerical and experimental study on the wave attenuation in bone--FDTD simulation of ultrasound propagation in cancellous bone

In cancellous bone, longitudinal waves often separate into fast and slow waves depending on the alignment of bone trabeculae in the propagation path. This interesting phenomenon becomes an effective tool for the diagnosis of osteoporosis because wave propagation behavior depends on the bone structure. Since the fast wave mainly propagates in trabeculae, this wave is considered to reflect the structure of trabeculae. For a new diagnosis method using the information of this fast wave, therefore, it is necessary to understand the generation mechanism and propagation behavior precisely. In this study, the generation process of fast wave was examined by numerical simulations using elastic finite-difference time-domain (FDTD) method and experimental measurements. As simulation models, three-dimensional X-ray computer tomography (CT) data of actual bone samples were used. Simulation and experimental results showed that the attenuation of fast wave was always higher in the early state of propagation, and they gradually decreased as the wave propagated in bone. This phenomenon is supposed to come from the complicated propagating paths of fast waves in cancellous bone.     

Application of an effective medium theory for modeling ultrasound wave propagation in healing long bones

Quantitative ultrasound has recently drawn significant interest in the monitoring of the bone healing process. Several research groups have studied ultrasound propagation in healing bones numerically, assuming callus to be a homogeneous and isotropic medium, thus neglecting the multiple scattering phenomena that occur due to the porous nature of callus. In this study, we model ultrasound wave propagation in healing long bones using an iterative effective medium approximation (IEMA), which has been shown to be significantly accurate for highly concentrated elastic mixtures. First, the effectiveness of IEMA in bone characterization is examined: (a) by comparing the theoretical phase velocities with experimental measurements in cancellous bone mimicking phantoms, and (b) by simulating wave propagation in complex healing bone geometries by using IEMA. The original material properties of cortical bone and callus were derived using serial scanning acoustic microscopy (SAM) images from previous animal studies. Guided wave analysis is performed for different healing stages and the results clearly indicate that IEMA predictions could provide supplementary information for bone assessment during the healing process. This methodology could potentially be applied in numerical studies dealing with wave propagation in composite media such as healing or osteoporotic bones in order to reduce the simulation time and simplify the study of complicated geometries with a significant porous nature.     

毫米波在等离子体中的衰减特性研究

为了研究毫米波与等离子体的相互作用,采用时域积分法对毫米波在等离子体中传输时的衰减特性进行了仿真,初步研究了毫米波在等离子体中传输时的衰减值与等离子体密度、碰撞频率及其工作频率之间的关系.通过理论结果和仿真结果的分析比较,验证了仿真可以为理论研究提供数据支撑的可行性. 关键词： 毫米波 等离子体 时域积分法 衰减     

Two new designs of lamp-type piezoelectric metamaterials for active wave propagation control

A major limitation of current metamaterials is that they control the wave propagation depending on their structure. Active metamaterials in this paper are designed whose physical structure is fixed, yet the position where they control the wave propagation can be changed by piezoelectric conditions. Two kinds of lamp-type piezoelectric metamaterials were assembled from an aluminum base, rubber plate and steel column, the piezoelectric patches were attached on both sides of the steel column, which can change the equivalent elastic modulus of the whole structure when the pair of patches are accessed by an LC circuit. The equivalent elastic modulus becomes zero or negative when the frequency of the circuit varies between 29,000 Hz and 30,000 Hz, in this case the two kinds of lamp-type piezoelectric metamaterials behave as a wave localization and a wave guide, respectively. The advantage of the lamp-type piezoelectric metamaterials is that we can control the wave propagation actively, as long as we change the position of the piezoelectric patches or choose the kind of lamp-type piezoelectric metamaterial. This is more flexible than a traditional passive metamaterial and provides a new way for us to design some acoustic equipment, such as acoustic cloaking, an acoustic black hole, filter or wave guide.     

Assessment of fatigue damage in solid plates through the ultrasonic Lamb wave approach

Changes(degradations) in the mechanical properties of solid plates induced by cyclic fatigue loading will influence the features of ultrasonic Lamb wave propagation,such as dispersion and attenuation.This paper has qualitatively analyzed the feasibility of using the amplitude-frequency characteristics and the stress wave factors(SWFs) of ultrasonic Lamb wave propagation to assess fatigue damage in solid plates.Liquid wedge transducers located on the surface of solid plates tested are used to generate and detect the Lamb wave signals.Based on the Ritec-SNAP ultrasonic measurement system,the experimental setup for assessing the degree of fatigue damage in solid plates using ultrasonic Lamb wave approach has been established.For several rolled aluminum sheets subjected to tension-tension cyclic loading,the experimental examinations have been performed for the relationships between the amplitude-frequency characteristics of ultrasonic Lamb wave propagation and the numbers of loading cycles(denoted by N),as well as the correlations between the Lamb wave SWFs and N.The experimental results show that the Lamb wave SWFs decrease monotonously and sensitively with the increment of cycles of fatigue loading.Based on the correlations between the Lamb wave SWFs and N,it is further verified that ultrasonic Lamb wave propagation combined with the Lamb wave SWFs can be used to effectively assess early fatigue damage in solid plates.     

受力腓肠肌剪切波速度的超声检测*

肌肉组织受力时的弹性特征变化,是其功能特性、健康状态的重要评估参量。该文利用在离体肌肉组织表面施加低频振动引起组织发生形变,在组织内部产生剪切波的方法,经过快速超声成像,通过剪切波图像估计剪切波的传播速度。研究结果表明顺肌纤维方向传播的剪切波速度快于垂直肌纤维方向传播的剪切波速度,剪切波的传播速度随受力的增加而变大,且顺肌纤维方向传播的剪切波速度与受力大小呈正相关。探讨肌纤维不同方向上的剪切波速度,为肌肉组织的病变及疲劳状态的检测和评估提供了参考。     

Ultrasonic slow waves in air-saturated cancellous bone

This paper describes preliminary observations of ultrasonic wave propagation in air-saturated defatted cancellous bone from the human vertebra. Using a broadband pulse transmission system, attenuation and phase velocity were measured over a wide frequency range (100 kHz-1 MHz). The observed behaviour was consistent with that expected for the decoupled slow wave predicted by Biot's theory. Velocity was lower than that of free air, and there was marked frequency-dependent attenuation and velocity dispersion. The tortuosity (alpha) of the trabecular microstructure was estimated from the high frequency limit of the dispersion curve, with a mean value of alpha = 1.040 +/- 0.004 obtained in five specimens. Ultrasonic measurements in air represent a valuable new approach, capable of yielding parameters that directly characterise bone structure. Furthermore, they may give useful insights into wave propagation in bone in vivo, where the trabecular framework is saturated with marrow fat rather than air.     

Ultrasonic wave propagation in heterogeneous solid media: theoretical analysis and experimental validation

This research deals with the ultrasonic characterization of thermal damage in concrete. This damage leads to the appearance of microcracks which then evolve in terms of volume rate and size in the material. The scattering of ultrasonic waves from the inclusions is present in this type of medium. The propagation of the longitudinal wave in the heterogeneous media is studied via a homogenization model that integrates the multiple scattering of waves. The model allows us to determine the phase velocity and the attenuation according to the elements which make the medium. Simulations adapted to the concrete are developed in order to test the responses of the model. These behaviors are validated by an experimental study: the measurements of phase velocity and attenuation are performed in immersion, with a comparison method, on a frequency domain which ranges from 160 kHz to 1.3 MHz. The analysis of different theoretical and experimental results obtained on cement-based media leads to the model validation, on the phase velocity behavior, in the case of a damage simulated by expanded polystyrene spheres in granular media. The application to the case of a thermally damaged concrete shows a good qualitative agreement for the changes in velocity and attenuation.