Barker码激励超声导波在长骨检测中的应用

单脉冲激励的超声导波在长骨中传播时,信号的衰减大,导致接收信号的幅度很小,且噪声严重。Barker码激励能有效增大接收信号幅度,提高信噪比(SNR)。将其应用到超声导波长骨检测中,进行仿真和长骨实验,得到的信号分别用加权匹配滤波器和有限冲激响应-最小均方误差(FIR-LS)逆滤波器进行压缩,并与单脉冲激励的结果进行了对比。结果表明,对于13位的Barker码,采用加权匹配滤波器进行解码时,压缩信号幅度是单脉冲激励接收信号的13倍;而FIR-LS逆滤波器则达到-63.59 dB的峰值旁瓣水平(PSL),更好地抑制噪声。说明可以将Barker码激励超声导波应用于长骨的检测中。      

时频方法分析长骨中的超声导波及皮质骨厚度

超声导波在长骨中传播时,接收信号中含有相互叠加的多个导波模式。本文提出将希尔伯特-黄变换(HHT)用于分析叠加的多模式导波信号,将其分解成许多单个独立的模式,然后对分解出的模式求得其对应频率下的群速度,并与短时傅里叶变换所得的结果进行比较。通过与理论计算结果比较,可得到长骨皮质骨的厚度。研究结果表明,实验得到的厚度与实际厚度一致。说明通过测量导波模式的速度可以评价皮质骨的厚度,也说明HHT方法是一种识别叠加多模式导波信号的有效方法。      

基于弹性模量检测骨疲劳的超声导波方法研究

研究早期诊断骨疲劳的方法是当前骨质评价方面的研究热点之一. 本文对不同弹性模量下长骨中超声导波的传播特性进行了理论分析和仿真研究.首先, 通过数值计算得到导波在管状长骨中的理论解析解.然后对管状长骨进行了时域有限差分(FDTD) 仿真, 并验证了它与理论解析解的一致性, 同时得到长骨中不同模式导波群速度、 中心频率和衰减与弹性模量的关系.研究结果表明各个导波模式的群速度和中心频率均随弹性模量的增加而增加, 而衰减随弹性模量的增加而减小.说明超声导波的传播特性参量可以反映长骨弹性模量的变化, 从而为长骨的早期疲劳诊断提供理论依据.     

小波时-频变换的高强钢丝弹性波传播模态分析

超声导波是近年来桥梁拉索无损检测研究的重要方法之一。针对弹性波在高强钢丝介质中传播的多模态频散问题,采用单点时域波形的小波时频变换进行混叠信号的模态识别分离。通过数值求解Pochhammer频率超越方程,计算得到0~1.5 MHz范围内纵向导波模态理论频散曲线;采用有限元模拟半波正弦脉冲激励导波在钢丝中传播过程,由小波时-频变换得到导波模态分布,并进行了不同腐蚀程度钢丝实验对比分析。结果表明,经小波时-频变换得到的第1、2、3阶纵向导波模态与理论值对应吻合,单点时域波形的小波时-频变换结果能够有效识别高强钢丝中的导波模态;钢丝在无腐蚀状态下,一阶纵向导波模态能量占比达57.74%,随腐蚀程度增加,能量更为集中到一阶纵波模态,二阶模态能量逐渐减小。     

长骨中振动声激发超声导波的方法

为了实现一定频段内任意低频下在长骨中激励导波信号,本文提出一种采用聚焦高频(5 MHz)超声换能器在长骨皮质骨中激发低频(150 kHz)超声导波的振动声方法.首先介绍了板状超声导波理论和双声束共聚焦法与单声束调幅法激发振动声的基本原理;进而采用三维有限元仿真方法分析振动声激发低频超声导波的基本现象,然后结合牛胫骨板离体实验,验证振动声激发低频超声导波的可行性.结果均表明,双声束共焦与单声束振动超声均可在骨板中激发低频超声导波.相关研究方法有助于提高空间域长骨中超声导波测量精度,以及在一定频段内实现任意频率激励等,对发展低频超声导波在体测量长骨皮质骨的新技术具有一定的指导意义.     

小波变换软阈值去噪在粗晶材料超声检测中的应用

本研究多尺度小波分析方法在粗晶材料超声检测信号增强中的应用。在分析结构噪声，电噪声和缺陷信号的小波变换特性的基础上，提出一种用一个尺度间变化的门限闭值来抑制噪声的小波变换系数，并以各尺度缺陷信号的能量关系形成权值，加权重构信号来提高信噪比。实验结果表明，该方法具有很好的去噪效果，增强了粗晶材料缺陷的检出率。     

激光超声检测中干涉特征提取算法的研究

为了有效地检测结构中的损伤位置及其形状,开展了基于超声导波干涉特征提取算法的损伤成像技术研究。在波场可视化的基础上,从波场历程中进一步分析了损伤对超声导波传播的影响;为了提取损伤附近超声导波干涉的能量,采用时间与空间域上的傅里叶变换对波场中的入射波和反射波进行分离,并根据计算出的干涉能量分布完成了损伤的成像;由于损伤产生的干涉能量在空间上的分布较广,为了减少损伤区域外的干涉能量,提高图像中损伤形状的分辨率,利用实Morlet小波分析的方法对宽频信号进行处理,提取窄带信号分量再进行干涉能量计算,提高了损伤成像的信噪比。     

骨折长骨中超声导波传播特性的仿真研究

采用超声导波评价长骨骨折已成为近两年来的一个研究热点.本文采用混合边界元方法(HBEM)对超声导波在骨裂长骨中的传播情况以及各导波模式的反射系数和透射系数进行了数值分析.研究结果表明,入射导波模式经由裂纹处模式转换后依然保持为主要接收模式不变.对某一裂纹,各模式透射系数常在相近的频率点上达到局部峰值.对于不同深宽比(d/w)裂纹,某些模式透射系数曲线局部峰值所对应的频率存在着相互错开的现象,这些结果可用于选择最优入射导波模式和频率,以便更好地定量评价骨质以及骨裂状况.     

基于小波变换的人体步态序列提取

将小波变换用于处理人体行走时产生的加速度信号.利用离散小波变换的多尺度、多分辨率特性对原始加速度信号进行尺度分解,在对小波基以及分解尺度进行合理选取后准确地从加速度信号中提取出隐藏的步态节律.与利用阈值法直接对原始加速度信号提取峰值的算法比较后发现：利用小波分解得到与步态节律相关的特征尺度后再进行峰值检测能显著地提高信号峰值的检出率;即使当原始信号存在较严重的噪声干扰时,该方法也能保证所提取出的步态序列的准确性.这对于步态序列的后续分析具有至关重要的意义.研究表明,离散小波变换是一种有效的提取步态节律的方 关键词： 小波变换 步态序列 峰值检测 特征尺度     

基于时频分布的盲信号分离方法研究长骨中的多模式导波信号

由于超声导波对长骨皮质骨的材料特性及厚度变化非常敏感,因此用导波评价长骨状况的研究已成为近年来的一个研究热点.在接收到的导波中,往往多种模式混叠在一起,使得进一步求取每种导波模式的群速度等与骨质状况密切相关的参数时遇到困难.本文采用基于时频分布的盲信号分离(TFBSS)方法对长骨中混叠的多模式进行分离,然后对分离后的单...     

Diagnosis of osteoporosis based on multi-scale wavelet parameters of ultrasonic guided waves

Evaluating bone regularly is important to prevent and control the disease of osteoporosis. Impact of osteoporosis on ultrasonic guided waves propagating in human long bones is studied in this paper. Multi-scale wavelet transform is proposed to process the received guided waves, and by analyzing energy changes in detail components of high order wavelet at different propagating distance to assess if osteoporosis happened. The guided waves signals are collected from the tibias of 13 volunteers. Based on the analysis of multi-scale wavelet transform, the high order detail components d6 and d5 changed dramatically with the propagation of ultrasonic guided waves along long bones, which means these 7 volunteers are diagnosed with osteoporosis. Compared with X-ray diagnosis, the effectiveness of this method can reach 92.3% in 13 volunteers. This suggests the multi-scale wavelet transform method is potential in ultrasonic assessment of bone quality.     

Multi-frequency axial transmission bone ultrasonometer

The last decade has seen a surge in the development of axial transmission QUS (Quantitative UltraSound) technologies for the assessment of long bones using various modes of acoustic waves. The condition of cortical bones and the development of osteoporosis are determined by numerous mechanical, micro-structural, and geometrical or macro-structural bone properties like hardness, porosity and cortical thickness. Such complex manifestations of osteoporosis require the evaluation of multiple parameters with different sensitivities to the various properties of bone that are affected by the disease. This objective may be achieved by using a multi-frequency ultrasonic examination The ratio of the acoustic wavelength to the cortical thickness can be changed by varying the frequency of the ultrasonic pulse propagating through the long bone that results in the change in composition of the induced wave comprised of a set of numerous modes of guided, longitudinal, and surface acoustic waves. The multi-frequency axial transmission QUS method developed at Artann Laboratories (Trenton, NJ) is implemented in the Bone Ultrasonic Scanner (BUSS). In the current version of the BUSS, a train of ultrasonic pulses with 60, 100, 400, 800, and 1200 kHz frequencies is used. The developed technology was tested on a variety of bone phantoms simulating normal, osteopenic, and osteoporotic bones. The results of this study confirm the feasibility of the multi-frequency approach for the assessment of the processes leading to osteoporosis.     

Analysis of ultrasonic guided waves propagating in long bones and cortical thickness based on time-frequency methods

The ultrasonic signals in long bones contain multiple guided modes which are mutual superposed.The velocities of guided waves in long bones are very sensitive to cortical thickness (CTh).In this paper,Hilbert-Huang transform(HHT) was proposed to analyze multi-mode guided waves,which can decompose superposed waves into many independent modes.Then the group velocity of each mode was obtained at corresponding frequency,which was compared with the results of short time Fourier transform(STFT).The CTh was also obtained by comparing with the theoretical calculation.The results showed that the experimental determined thickness was in agreement with the actual CTh,indicating that measuring the velocity of the guided mode can be used to estimate the CTh.The HHT is an effective method to identify multimode guided waves.     

A numerical study on the propagation of Rayleigh and guided waves in cortical bone according to Mindlin's Form II gradient elastic theory

Cortical bone is a multiscale heterogeneous natural material characterized by microstructural effects. Thus guided waves propagating in cortical bone undergo dispersion due to both material microstructure and bone geometry. However, above 0.8 MHz, ultrasound propagates rather as a dispersive surface Rayleigh wave than a dispersive guided wave because at those frequencies, the corresponding wavelengths are smaller than the thickness of cortical bone. Classical elasticity, although it has been largely used for wave propagation modeling in bones, is not able to support dispersion in bulk and Rayleigh waves. This is possible with the use of Mindlin's Form-II gradient elastic theory, which introduces in its equation of motion intrinsic parameters that correlate microstructure with the macrostructure. In this work, the boundary element method in conjunction with the reassigned smoothed pseudo Wigner-Ville transform are employed for the numerical determination of time-frequency diagrams corresponding to the dispersion curves of Rayleigh and guided waves propagating in a cortical bone. A composite material model for the determination of the internal length scale parameters imposed by Mindlin's elastic theory is exploited. The obtained results demonstrate the dispersive nature of Rayleigh wave propagating along the complex structure of bone as well as how microstructure affects guided waves.     

超声轴向传播技术评价长骨的研究

用超声轴向传播技术评价长骨状况已成为近年来的一个研究热点。本文首先介绍了第一到达波(FAS)法、超声Lamb波及柱面导波法在评价长骨皮质骨状况方面的研究进展,最后分析和讨论了当前研究中存在的问题及应该研究的方向。     

Hidden corrosion detection in aircraft aluminum structures using laser ultrasonics and wavelet transform signal analysis

Preliminary results of hidden corrosion detection in aircraft aluminum structures using a noncontact laser based ultrasonic technique are presented. A short laser pulse focused to a line spot is used as a broadband source of ultrasonic guided waves in an aluminum 2024 sample cut from an aircraft structure and prepared with artificially corroded circular areas on its back surface. The out of plane surface displacements produced by the propagating ultrasonic waves were detected with a heterodyne Mach-Zehnder interferometer. Time-frequency analysis of the signals using a continuous wavelet transform allowed the identification of the generated Lamb modes by comparison with the calculated dispersion curves. The presence of back surface corrosion was detected by noting the loss of the S(1) mode near its cutoff frequency. This method is applicable to fast scanning inspection techniques and it is particularly suited for early corrosion detection.     

Propagation of time-reversed Lamb waves in acrylic cylindrical tubes as cortical-bone-mimicking phantoms

The present study aims to investigate the propagation of time-reversed Lamb waves in acrylic cylindrical tubes as cortical-bone-mimicking phantoms. Time-reversed Lamb waves could be successfully launched in 6 acrylic tubes with wall thicknesses from 2 to 12 mm by using a modified time reversal method. The group velocities of the time-reversed Lamb waves in the acrylic tubes were measured by using the axial transmission technique. They decreased very slightly with increasing wall thickness, showing good agreement with the theoretical group velocity of the A0 Lamb wave in the acrylic plate. These results suggest that the time-reversed Lamb waves in the acrylic tubes would essentially behave as the A0 Lamb wave, consistent with the behavior of the slow guided wave in long cortical bones. It is expected that the application of the time-reversed Lamb waves in long bones would enhance clinical potential of ultrasonic technologies for the diagnosis of osteoporosis.     

Wavelet-transform analysis and filtering of signals produced by an ultrasonic laser interferometer

Methods based on the discrete wavelet transform are used to study ultrasonic pulses in aluminum single crystals. Longitudinal elastic waves propagating in the [111] crystallographic direction were generated at 5 MHz. Methods for filtering images of an acoustic field on the basis of wavelet transform are developed. Recommendations on the choice of filtering parameters are given.