全息光栅的制造技术及其改进

本文叙述了全息光栅的制造原理、工艺要求和制造技术。介绍了平场全息光栅、图象全息光栅、超环面全息光栅、激光全患光栅和闪耀全息光栅的新进展。最后,作者提出进一步发展全息光栅的若干建议。     

2000 l/mm X射线镂空透射光栅的制备研究

在满足工艺要求的前提下,通过模拟光栅衍射,设计出镂空透射光栅模型,在此基础上将电子束和X射线光刻技术相结合,研究了制造2000 l/mm X射线镂空透射光栅的新工艺技术.首先利用电子束光刻和微电镀技术在镂空聚酰亚胺薄膜底衬上制备X射线母光栅掩模.然后利用X射线光刻和微电镀技术实现了光栅图形的复制,之后采用紫外光刻和微电镀技术制作加强筋结构,最后通过腐蚀体硅和等离子体刻蚀聚酰亚胺完成镂空透射光栅的制作.从此新的制造工艺结果上来看.制备的光栅栅线平滑,占空比合理,侧壁陡直,不同光栅之间一致性好,完全可以满足应用需求,充分表明了该制造技术是透射式X射线衍射光学元件制造的良好选择.     

Rewritable densification gratings in boron-doped fibers

We show that the strength of long-period gratings recorded in boron-doped fibers by CO2 radiation can be significantly enhanced by a uniform pre-exposure by the same laser. The resultant gratings could be erased by a similar uniform exposure and then recorded again multiple times with no loss of fiber sensitivity. We suggest that such gratings are formed by reversible densification of the fiber core. These densification gratings have higher thermal stability than gratings written with ultraviolet light.     

Visualization of type II fiber Bragg gratings induced in a birefringent fiber with an elliptical stress cladding

Experimental results on visualization of type II fiber Bragg gratings induced in a birefringent fiber with an elliptical stress cladding are presented. The gratings are recorded by a single pulse of an excimer KrF-laser by means of the phase-mask method. Images of the gratings are obtained in a bright field using contrasting techniques such as differential interference contrast and dark field. It is shown that single-pulse recording forms several type II Bragg gratings in the optical fiber. The spatial profile of these gratings corresponds to the phase mask period. Microcracks due to which type II gratings are induced are localized both on the boundaries between the fiber core and claddings surrounding it and at some distance from them.     

Fabrication of long-period fiber gratings by focused irradiation of infrared femtosecond laser pulses

We have fabricated long-period fiber gratings by use of a novel technique using focused irradiation of infrared femtosecond laser pulses. We investigate the thermal stability of the fabricated fiber gratings. The values of the loss peak wavelength and the transmittance of the fiber gratings after heat treatment below 500 degrees C are the same as initial values before heat treatment. The fiber gratings that were fabricated by this technique have a high resistance to thermal decay. We propose that this technique will be useful for fabrication of fiber gratings with a superior aging characteristic.     

多层光纤布拉格光栅的理论与实验研究

从理论和实验两方面研究了在非周期性多层光纤上写入布拉格光栅的光学特性。从耦合模理论出发,讨论了光纤具有多于一个光敏层的情况。在实验室自制的两类多层光纤上写入光栅的实验也表明,该类光栅具备有一般光栅的普遍光学特性,说明在使用多层光纤作为关键部分构建器件时,需要的各类光栅部件能够通过直接在该类光纤上写入光栅实现。紫外光在氢载掺铒多层光纤上写入光栅的实验说明分层的异种元素掺杂将导致芯区应力增加,从而辅助提高光纤的光敏性。     

Optimization of near-field optical field of multi-layer dielectric gratings for pulse compressor

Multi-layer dielectric (MLD) gratings for pulse compressors in high-energy laser systems should provide high diffraction efficiency as well as high laser induced damage thresholds (LIDT). Nonuniform optical near-field distribution is one of the important factors to limit their damage resistant capabilities. Electric field distributions in the gratings and multi-layer film region are analyzed by using Fourier modal method. Optimization of peak electric field in the gratings ridge is performed with a merit function, including both diffraction efficiency and electric field enhancement when the top layer material is HfO₂ and SiO₂, respectively. A set of optimized gratings parameters is obtained for each structure, which reduce the peak electric field within the gratings ridge to being respective 1.39 and 1.84 times the value of incident light respectively. Finally, we also discuss the effects of gratings refractive index, gratings sidewall angle and incident angle on peak electric field in the gratings ridge.     

Efficient iterative technique for designing Bragg gratings

We present a new iterative method for designing Bragg gratings based on the Levenberg-Marquardt method of minimizing a chi-squared merit function. It is effective for designing both weak and strong gratings and is particularly well suited for unchirped gratings.     

Diffraction from metallic gratings with locally varying profile forms

Measurements of the diffraction characteristics of one-dimensional surface-relief gratings of locally varying profile are compared with rigorous diffraction theory. These gratings result from the superposition of two linear sinusoidal gratings of uniform depth for which the relative phase between the two gratings varies slowly with position. The resultant surface profile exhibits a relatively large-period variation in profile form. The periodic variation in diffraction efficiency that results yields a visual moiré pattern that has interesting asymmetry and polarization properties that alter as the viewing conditions are changed; the gratings can be exploited by diffractive optically variable devices for document security.     

Fabrication of planar gratings by direct ablation using an ultrashort pulse laser in a common optical path configuration

Planar gratings have wide applications and to date, many methods for the fabrication of gratings have been reported. Ultrashort pulse lasers have been used for the machining of gratings primarily because they allow direct ablation and the manufacturing of sub-wavelength structures. In this paper, we present a novel direct ablation technique for the fabrication of planar gratings which makes use of the interference of ultrashort pulses in a common optical path configuration. This technique of grating fabrication not only simplifies the optical setup, but also immunizes the system to extraneous and inherent vibrations, thus enabling the manufacturing of planar gratings of good edge acuity. We have successfully fabricated planar gratings on a copper substrate. Received: 6 November 2001 / Accepted: 4 March 2002 / Published online: 10 September 2002 RID="*" ID="*"Corresponding author. Fax: +65/77-904-674, E-mail: mvenkata@ntu.edu.sg     

Thin and thick diffraction gratings: Thin matrix decomposition method

A brief review of the properties of transmission diffraction gratings is presented. Two types of gratings will be analyzed: thin and volume gratings explaining how the efficiency of the different orders that propagate inside the gratings can be calculated in both cases. For thin diffraction gratings the so-called amplitude transmittance method is applied in order to get the amplitude of the different orders, whereas in the case of volume gratings more complex methods are needed, such as Coupled Wave or modal theories. We will comment on the thin matrix decomposition method (TMDM), firstly proposed by Alferness, which gives a very intuitive approach and connects the properties of thin gratings to the properties of volume ones. The thin matrix decomposition method consists in dividing the volume grating in a number of thin gratings and applying the amplitude transmittance method to each thin grating. In this way the output of a grating will be considered as the input of the next and any individual grating can be treated by the amplitude transmittance method. The novelty of this work is that a comparison is made between the analytical expressions obtained by Alferness using the TMDM with the numerical results obtained using the coupled wave (CW) and rigorous coupled wave (RCW) theories for the efficiencies of the zero, first and second order when a plane wave incides onto a sinusoidal diffracion grating at the second on-Bragg replay angular condition.     

三角形大带宽反射光谱光纤光栅的设计和制备

反射谱具有三角形形状的光纤光栅在光纤传感等领域中具有重要的应用前景。利用遗传算法设计出了产生三角形光谱分布的光纤光栅的耦合系数沿光纤的分布。计算表明,三角形光谱光纤光栅是可以实现的,其反射带宽可以通过光栅的啁啾量进行调节,常周期的三角光栅反射带宽小,变周期的三角光栅反射带宽大,其带宽同其啁啾量大致相等。实验中,采用光束扫描法制备了反射底宽为0．77nm三角形光谱的光纤光栅。     

Transition radiation in a system of two cascaded gratings

Transition radiation that arises when a charged particle passes through two consecutive plane gratings is considered. The gratings are made up of parallel metal wires. The planes of the gratings are parallel to each other and perpendicular to the direction of motion of the particle. The conductors of one of the gratings are perpendicular to the conductors of the other. It is shown that the generated transition radiation has elliptic polarization; the ellipticity and the sign of rotation depend on the angle of radiation, the distance between the gratings, and the velocity of the charged particle.     

Plasmon resonances in deep nanogrooves of reflective metal gratings

Metallic gratings with very deep and narrow grooves are fabricated and their reflection spectra are characterized, which explicitly show high-order standing-wave-like resonances of surface plasmons in the cavity of nanogrooves. The effect of in-plane surface plasmon resonance is also observed, which is shown to have only a minor role on the reflection of such gratings, unlike that for shallow gratings. Using numerical simulations, the cavity resonances and their effects on the reflection of the gratings are identified and further analyzed. As field is more enhanced in the nanogrooves under cavity resonance conditions, the enhancement is also found to be dependent on the grating period, i.e. the strongest enhancement takes place for higher-order resonance modes for smaller grating period. For gratings with shallower grooves, comparable enhancement of field is also achievable by proper design of the grating period. The study suggests that field enhancement can be realized at selective wavelengths in a wide spectrum range using cavity resonances in the deep nanogrooves of metal gratings, and the position for field-enhancement can be tuned by the depth and period of the gratings.     

全息离子束刻蚀衍射光栅

全息离子束刻蚀衍射光栅集中了机械刻划光栅的高效率和全息光栅的无鬼线、低杂散光、高信噪比的优点．全息离子束刻蚀已作为常规工艺手段应用于真空紫外及软x射线衍射光栅的制作．文章对全息离子束刻蚀衍射光栅的制作方法、主要类型、研究现状和应用进行了综述．     

Analysis of optical propagation in thick holographic gratings

A method of analyzing optical propagation in thick holographic gratings by decomposition of the thick material into thin gratings is discussed. The method is readily applicable to study propagation in multiple gratings of arbitrary spatial frequency and orientation recorded in the same thick emulsion. Applied to the double grating case, the method predicts strong cross-coupling between the two gratings for proper relative slope of the gratings. Results are given.     

Surface-relief diffraction gratings recorded by multiple-beam coherent phase exposure

Surface-relief hexagonal-array diffraction gratings have been produced by three-beam coherent exposure. Collimated light was used in an attempt to produce a uniform relief profile over the total area of a 7.6-cm plate coated with a positive photoresist. The resulting gratings were reproduced in nickel by an electroforming process and analyzed by atomic force microscopy. The topography of the gratings was found to be that predicted by theory. The results obtained show that the gratings were of uniform profile over their total area.     

间隔叠合式双层亚波长光栅

提出了一种应用价值较高的防伪光栅结构-间隔叠合式双层亚波长光栅,可以展宽基本光栅的光谱峰值带宽、改善光谱线形和光变效果.分析了亚波长光栅光谱峰值带宽展宽和线形改善的原理,用矢量衍射理论验证了理论分析的合理性,并对特定防伪光变设计要求的双层光栅进行了参量优化和光变特性分析.结果表明,满足同相位条件的光谱线形与基本光栅相同,带宽为基本光栅的两倍;满足反相位条件的光谱线形为准矩形,带宽大于基本光栅;亚波长光栅在传统和非传统照明条件下倾斜均能产生彩色光变效果,且传统照明情况下的光变速率较大,利用这种光变速率差可以制作各向异性光变效果.     

Holographic nanocomposite and a related diffraction element

Highly selective volume-diffraction gratings are recorded on a holographic acrylate nanocomposite. The holographic characteristics of the gratings are studied. It is shown that the diffraction efficiency of gratings can reach 50% and a 3D hologram is formed. The refractive index modulation is 0.048–0.065.