非晶硅锗电池性能的调控研究

采用射频等离子体增强化学气相沉积技术, 研究了非晶硅锗薄膜太阳电池. 针对非晶硅锗薄膜材料的本身特性, 通过调控硅锗合金中硅锗的比例, 实现了对硅锗薄膜太阳电池中开路电压和短路电流密度的分别控制. 借助于本征层硅锗材料帯隙梯度的设计, 获得了可有效用于多结叠层电池中的非晶硅锗电池. 关键词： 非晶硅锗薄膜太阳电池 短路电流密度 开路电压 带隙梯度     

氢化纳米硅薄膜中氢的键合特征及其能带结构分析

对氢化纳米硅薄膜中氢的键合特征和薄膜能带结构之间的关系进行了研究.所用样品采用螺 旋波等离子体化学气相沉积技术制备，利用Raman散射、红外吸收和光学吸收技术对薄膜的 微观结构、氢的键合特征以及能带结构特性进行了分析.Raman结果显示不同衬底温度下所生 长薄膜的微观结构存在显著差异，从非晶硅到纳米晶硅转化的衬底温度阈值为200℃.薄膜中 氢的键合特征与薄膜的能带结构密切相关.氢化非晶硅薄膜具有较高的氢含量，因键合氢引 起的价带化学位移和低衬底温度决定的结构无序性，使薄膜呈现较大的光学带隙和带尾宽度 .升 关键词： 氢化纳米硅 螺旋波等离子体 能带结构     

立方氮化硼薄膜的光学带隙

用射频溅射法在p型Si(100)衬底上沉积立方氮化硼(c-BN)薄膜,薄膜的成分由傅里叶变换红外谱标识,用紫外-可见分光光度计测量了c-BN薄膜的反射光谱,利用K-K(Kramers-Kroning)关系从反射谱计算出c-BN薄膜的光吸收系数,进而确定c-BN薄膜的光学带隙.对于立方相含量为55.4%的c-BN薄膜,光学带隙为5.38eV. 关键词： 立方氮化硼薄膜 光学带隙 K-K关系     

低温铝诱导晶化制备纳米晶硅薄膜的物相和光学性能研究

采用射频磁控溅射镀膜系统,在玻璃衬底上制备了非晶硅(α-Si)/铝(Al)复合薄膜,结合氮气(N₂)气氛中低温快速光热退火制备了纳米晶硅(nc-Si)薄膜;利用光学显微镜、共焦光学显微仪、X射线衍射(XRD)仪、拉曼散射光谱(Raman)仪和紫外-可见光-近红外分光光度计(UV-VIS-NIR)对纳米晶硅薄膜的表面形貌、物相及光学性能进行了表征,研究了退火工艺对薄膜性能的影响。结果表明： 300 ℃,25 min光热退火可使α-Si/Al膜晶化为纳米晶硅薄膜,晶化率为15.56%,晶粒尺寸为1.75 nm;退火温度从300 ℃逐渐升高到400 ℃,纳米晶硅薄膜晶粒尺寸、晶化率、带隙逐渐增加,表面均匀性、晶格畸变量逐渐减小;退火温度从400 ℃逐渐升高到500 ℃,纳米晶硅薄膜的晶粒尺寸、晶化率继续增加,带隙则逐渐降低;采用纳米晶硅薄膜的吸光模型验证了所制备的纳米晶硅薄膜的光学特性,其光学带隙的变化趋势与吸光模型得出的结果一致。     

沉积压力对氢化非晶硅薄膜特性的影响

采用等离子增强化学气相沉积(PECVD)系统,以乙硅烷和氢气为气源,普通钠钙玻璃为衬底制备了氢化非晶硅(a-Si∶H)薄膜,研究了沉积压力对非晶硅薄膜的沉积速率、光学带隙以及结构因子的影响。采用台阶仪、紫外可见分光光度计、傅里叶变换红外光谱仪和扫描电子显微镜等手段分别表征了a-Si∶H薄膜的沉积速率,光学带隙、结构因子和表面形貌。结果表明： 随着沉积压力的增加,沉积速率呈现先上升后下降的趋势,光学带隙不断下降。当沉积压力小于210 Pa时,以SiH键存在的H原子较多,而以SiH₂或SiH₃等形式存在的H较少; 当沉积压力大于210 Pa时,以SiH₂,(SiH₂)_n或SiH₃等形式存在的H较多。通过结构因子的计算,发现沉积压力在110～210 Pa的范围内沉积的薄膜质量较好。     

电子回旋共振等离子体增强沉积氟化非晶碳薄膜的光学性质

用紫外可见光透射光谱(UV-VIS)并结合键结构的X射线光电子能谱(XPS)和红外谱(FTIR)分析,研究了电子回旋共振等离子体增强化学气相沉积法制备的氟化非晶碳薄膜的光吸收和光学带隙性质.在微波功率为140—700W、源气体CHF₃∶C₆H₆比例为1∶1—10∶1条件下沉积的薄膜,光学带隙在1.76—2.85eV之间.薄膜中氟的引入对吸收边和光学带隙产生较大的影响,吸收边随氟含量的提高而增大,光学带隙则主要取决于CF键的含量,是由于强电负 关键词： 氟化非晶碳薄膜 光吸收与光学带隙 电子回旋共振等离子体     

氮化硅薄膜中纳米非晶硅颗粒的键合结构及光致发光

采用螺旋波等离子体化学气相沉积技术以N₂/SiH₄/H₂为反应气体制备了镶嵌有纳米非晶硅颗粒的氢化氮化硅薄膜,通过改变N₂流量实现了薄膜从红到蓝绿的可调谐光致发光.傅里叶红外透射和紫外-可见光吸收特性分析表明,所生长薄膜具有较高的氢含量,N₂流量增加使氢的键合结构发生变化,非晶硅颗粒尺寸减小,所对应的薄膜的光学带隙逐渐增加和微观结构有序度减小.可调光致发光(PL)主要来源于纳米硅颗粒的量子限制效应发光,随N₂流量增加,PL的谱线展宽并逐渐增强. 关键词： 傅里叶红外透射谱 光吸收谱 纳米硅粒子镶嵌薄膜 光致发光     

氟化非晶碳薄膜的光学带隙分析

研究了CHF3C6H6沉积的氟化非晶碳(αC∶F)薄膜的光学带隙.发现αC∶F薄膜光学带隙的大小取决于薄膜中C—F,CC的相对含量.这是由于CC形成的窄带隙π键和C—F形成的宽带隙σ键含量的相对变化,改变了带边态密度分布的结果.在微波功率为140—700W、沉积气压为01—10Pa、源气体CHF3∶C6H6流量比为1∶1—10∶1条件下沉积的αC∶F薄膜,光学带隙在176—398eV之间 关键词： 氟化非晶碳(αC∶F)薄膜 光学带隙 键结构     

氢稀释对FTS沉积a-Si∶H薄膜结构特性的影响

采用对靶磁控反应溅射技术,以氢气作为反应气体在不同的氢稀释比条件下制备了氢化非晶硅薄膜.利用台阶仪、傅里叶红外透射光谱、Raman谱和紫外-可见光透射谱测量研究了不同氢稀释比对氢化非晶硅薄膜生长速率和结构特性的影响.分析结果发现,利用对靶磁控溅射技术能够实现低温快速沉积高质量氢化非晶硅薄膜的制备.随着氢稀释比不断增加,薄膜沉积速率呈现先减小后增大的趋势.傅里叶红外透射光谱表明,氢化非晶硅薄膜中氢含量先增大后变小.而Raman谱和紫外-可见光透射谱分析发现,氢稀释比的增加使氢化非晶硅薄膜有序度和光学带隙均先增大后减小.可见,此技术通过改变氢稀释比R能够实现氢化非晶硅薄膜结构的有效控制.     

氢稀释对FTS沉积a-Si:H薄膜结构特性的影响

采用对靶磁控反应溅射技术,以氢气作为反应气体在不同的氢稀释比条件下制备了氢化非晶硅薄膜.利用台阶仪、傅里叶红外透射光谱、Raman谱和紫外-可见光透射谱测量研究了不同氢稀释比对氢化非晶硅薄膜生长速率和结构特性的影响.分析结果发现,利用对靶磁控溅射技术能够实现低温快速沉积高质量氢化非晶硅薄膜的制备.随着氢稀释比不断增加,薄膜沉积速率呈现先减小后增大的趋势.傅里叶红外透射光谱表明,氢化非晶硅薄膜中氢含量先增大后变小.而Raman谱和紫外-可见光透射谱分析发现,氢稀释比的增加使氢化非晶硅薄膜有序度和光学带隙均先增大后减小.可见,此技术通过改变氢稀释比R能够实现氢化非晶硅薄膜结构的有效控制.     

Identification of the double and single acceptor state of isolated NiGa in GaAs

The question of the exact energy positions of isolated Ni_Ga as well as their optical and electrical properties have not yet been fully clarified in GaAs. We present a systematic study by deep-level transient spectroscopy, deep-level optical spectroscopy and optical absorption performed on several Ni-doped GaAs materials: n- and p-type LEC (liquid-encapsulated Czochralski) grown and p-type layers grown by liquid-phase epitaxy (LPE). All the electrical and optical results are up to now relatively coherent with the following identifications: (i) the double-acceptor charge state (Ni⁺ /Ni²⁺) is at E_c - 0.4 eV, (ii) the single-acceptor charge state (Ni²⁺ / Ni³⁺) is at E_v + 0.2 eV. However, when Ni is introduced during LPE in p-type materials we do not detect the Ni²⁺ /Ni³⁺ level which suggest a very low solubility of Ni in the LPE growth conditions.     

Transport and optical properties of amorphous carbon and hydrogenated amorphous carbon films

In this paper we report on the electrical and optical properties of amorphous carbon (a-C) and hydrogenated amorphous carbon (a-C:H) films. Resistivity of both types of films decreases with increase in temperature. At lower temperatures (60-250 K) the electron transport is due to variable range hopping for the a-C films. At higher temperatures (300-430 K) it is thermally activated for both types of films. Analysis of the heterojunction between diamond-like carbon (DLC) and bulk silicon (Si) leads to the conclusion that our a-C films are of n-type and our a-C:H films are of p-type. The optical measurements with DLC revealed a Tauc bandgap of 0.6 eV for the a-C films and 1-1.2 eV for the a-C:H films. An Urbach energy around 170 meV could be determined for the a-C:H films. Strain versus resistance plots were measured resulting in piezoresistive gauge factors around 50 for the a-C films and in between 100 and 1200 for the a-C:H films.     

Characterization of thermal, optical and carrier transport properties of porous silicon using the photoacoustic technique

In this work, the porous silicon layer was prepared by the electrochemical anodization etching process on n-type and p-type silicon wafers. The formation of the porous layer has been identified by photoluminescence and SEM measurements. The optical absorption, energy gap, carrier transport and thermal properties of n-type and p-type porous silicon layers were investigated by analyzing the experimental data from photoacoustic measurements. The values of thermal diffusivity, energy gap and carrier transport properties have been found to be porosity-dependent. The energy band gap of n-type and p-type porous silicon layers was higher than the energy band gap obtained for silicon substrate (1.11 eV). In the range of porosity (50-76%) of the studies, our results found that the optical band-gap energy of p-type porous silicon (1.80-2.00 eV) was higher than that of the n-type porous silicon layer (1.70-1.86 eV). The thermal diffusivity value of the n-type porous layer was found to be higher than that of the p-type and both were observed to increase linearly with increasing layer porosity.     

Rb吸附石墨烯纳米带电子性质和光学性质的研究

本文基于密度泛函理论的第一性原理方法了计算了Rb、O和H吸附石墨烯纳米带的差分电荷密度、能带结构、分波态密度和介电函数，调制了石墨烯纳米带的电子性质和光学性质，给出了不同杂质影响材料光学特性的规律.结果表明本征石墨烯纳米带为n型直接带隙半导体且带隙值为0.639 eV；Rb原子吸附石墨烯纳米带之后变为n型简并直接带隙半导体，带隙值为0.494eV；Rb和O吸附石墨烯纳米带变为p型简并直接带隙半导体，带隙值增加为0.996eV；增加H吸附石墨烯纳米带后，半导体类型变为n型直接带隙半导体，且带隙变为0.299eV，带隙值相对减小，更有利于半导体发光器件制备.吸附Rb、O和H原子后，石墨烯纳米带中电荷密度发生转移，导致C、Rb、O和H之间成键作用显著.吸附Rb之后，在费米能级附近由C-2p、Rb-5s贡献；增加O原子吸附之后，O-2p在费米能级附近贡献非常活跃，杂化效应使费米能级分裂出一条能带；再增加H原子吸附之后，Rb-4p贡献发生蓝移，O-2p在费米能级附近贡献非常强，费米能级分裂出两条能带.Rb、O和H的吸附后，明显调制了石墨烯纳米带的光学性质.     

Microcrystalline silicon oxide (μc-SiO:H) alloys as a contact layer for highly efficient Si thin film solar cell

We observe >6% efficiency enhancement in silicon thin film solar cell using a p-type microcrystalline silicon oxide (μc-SiO:H) contact layer between transparent conducting oxide (TCO) electrode and the hydrogenated amorphous silicon (a-Si:H) layer. The role of the above contact layer is to reduce the Schottky barrier effect as well as the hetero-junction barrier formation at the interface. Despite its nanometer scale thickness, the properties of the contact layer significantly affect the solar parameters. Based on our results, p-type doped μc-SiO:H can be an ideal material as a contact layer due to its good optical response without noticeable degradation in its electrical property.     

氢稀释制备的非晶碳膜的绿光和蓝光发射

在电容耦合式PECVD系统中,以CH4和H2为气源,通过控制H2的流量制备了一系列氢化非晶碳膜（a-C:H)样品。利用傅里叶变换红外光谱（FTIR）、光致发光谱（PL）和吸收谱对a-C:H膜的结构及光学性质进行了研究。结果表明：氢稀释可以在一定程度上减少碳的sp^2团簇的形成,增大它的光学带隙,并改变薄的微结构。与此同时,光致发光峰随郑 光学带隙的增大而蓝移;当光学带隙增大2．72eV时,出现了2．4eV（绿光）和2．97eV(蓝光）组成的发光峰。     

Spectroscopic determination of the position of the ferm-level in doped amorphous hydrogenated silicon

The variation of the Fermi energy E_F of _a-Si:H with boron or phosphorus doping has been determined by means of photoelectron spectroscopy. The results are shown to be consistent with those obtained from the activation energy of the conductivity. The p-type charge carriers are concentrated in a region 0.3 eV above the spectroscopically determined valence band edge.     

第一性原理研究B掺杂Mn_4Si_7的电子结构和光学性质

采用基于密度泛函理论的第一性原理计算方法,对未掺杂及B掺杂Mn_4Si_7的电子结构和光学性质进行理论计算.研究结果表明,未掺杂Mn_4Si_7是间接带隙半导体,其禁带宽度为0.786 eV,B掺杂后其禁带宽度下降为0.723 eV. B掺杂Mn_4Si_7是p型半导体材料.未掺杂Mn_4Si_7在近红外区的吸收系数达到10~5 cm~(-1),B掺杂引起Mn_4Si_7的折射率、吸收系数、反射系数及光电导率增加.     

DNA-based organic-on-inorganic semiconductor Schottky structures

A sandwich device has been fabricated from DNA molecular film by solution processing located between Al and p-type silicon inorganic semiconductor. We have performed the electrical characteristics of the device such as current–voltage (I–V), capacitance–voltage (C–V) and capacitance–frequency (C–f) at room temperature and in dark. The DNA-based structure has showed the rectifying behavior. From its optical absorbance spectrum, it has been seen that DNA has been a semiconductor-like material with wide optical band energy gap of 4.12 eV and resistivity of 1.6 × 10¹⁰ Ω cm representing a p-type conductivity.     

RETRACTED ARTICLE: Hydrogenated nanocrystalline silicon germanium thin films

Hydrogenated nanocrystalline silicon germanium thin films (nc-SiGe:H) is an interesting alternative material to replace hydrogenated nanocrystalline silicon (nc-Si:H) as the narrow bandgap absorber in an a-Si/a-SiGe/nc-SiGe(nc-Si) triple-junction solar cell due to its higher optical absorption in the wavelength range of interest. In this paper, we present results of optical, structural investigations and electrical characterization of nc-SiGe:H thin films made by hot-wire chemical vapor deposition (HW-CVD) with a coil-shaped tungsten filament and with a disilane/germane/hydrogen gas mixture. The optical band gaps of a-SiGe:H and nc-SiGe:H thin-films, which are deposited with the same disilane/germane/hydrogen gas mixture ratio of 3.4 : 1.7 : 7, are about 1.58 eV and 2.1 eV, respectively. The nc-SiGe:H thin film exhibits a larger optical absorption coefficient of about 2–4 in the 600–900 nm range when compared to nc-Si:H thin film. Therefore, a thinner nc-SiGe:H layer of ∼500 nm thickness may be sufficient for the narrow bandgap absorber in an a-Si based multiple-junction solar cell. We enhanced the transport properties as measured by the photoconductivity frequency mixing technique. These improved alloys do not necessarily show an improvement in the degree of structural heterogeneity on the nanometer scale as measured by smallangle X-ray scattering. Decreasing both the filament temperature and substrate temperature produced a film with relatively low structural heterogeneity while photoluminescence showed an order of magnitude increase in defect density for a similar change in the process.