Weathering of copper-amine treated wood

In this study, the effect of ultraviolet light (UV) irradiation and water spray on color, contact angle and surface chemistry of treated wood was studied. Southern pine sapwood (Pinus Elliottii.Engelm.) treated with copper ethanolamine (Cu-MEA) was subjected to artificially accelerated weathering with a QUV Weathering Tester. The compositional changes and the surface properties of the weathered samples were characterized by Fourier transform infrared (FTIR) spectroscopy, color and contact angle measurements. FTIR indicated that MEA treatment was not found to slow down wood weathering. FTIR spectrum of MEA-treated sample was similar to that of the untreated SP. However, the Cu-MEA treatment retarded the surface lignin degradation during weathering. The main changes in FTIR spectrum of Cu-MEA treatment took place at 915, 1510, and 1595 cm⁻¹. The intensity of the bands at 1510 and 1595 cm⁻¹ increased with the Cu-MEA treatment. Both untreated and MEA-treated exhibited higher ΔE than the Cu-MEA treated samples, indicating that MEA treatment did not retard color changes. However, ΔE decreased with increasing copper concentration, suggesting a positive contribution of Cu-EA to wood color stability. The contact angle of untreated and MEA-treated samples changed rapidly, and dropped from 75 ± 5° to 0° after artificial weathering up to 600 h. Treatment with Cu-MEA slowed down the decreasing in contact angle. As the copper concentration increases, the rate of change in contact angle decreases.     

Effect of accelerated weathering on surface chemistry of modified wood

In this study, the effects of UV-light irradiation and water spray on colour and surface chemistry of scots pine sapwood samples were investigated. The specimens were treated with chromated copper arsenate (CCA), a metal-free propiconazol-based formulation, chitosan, furfuryl alcohol and linseed and tall oils. The weathering experiment was performed by cycles of 2 h UV-light irradiation followed by water spray for 18 min. The changes at the surface of the weathered samples were characterised by Fourier transform infrared spectroscopy (FT-IR); colour characterizations were performed by measuring CIELab parameters.The results show that all treatment methods except chitosan treatment provided lower colour changes than the control groups after 800 h exposure in weathering test cycle, but differences between chitosan and control were also small. The lowest colour changes were found on linseed oil (full cell process) and CCA treated wood. FT-IR results show that oil treatment (linseed and tall oil) decreased the intensities of a lignin specific peak (1500-1515 cm⁻¹). Absorption band changes at 1630-1660 cm⁻¹ were reduced by all treatments.     

Relationship between electronic and crystal structure in Cu–Ni–Co–Mn–O spinels: Part B: Binding energy anomaly in Cu photoemission spectrum

In very rare circumstances, X-ray photoemission spectra of copper in spinel oxides exhibit a “negative binding energy shift”. The origin of such an anomalous XPS chemical shift was investigated. A metastable Ni_0.48Co_0.24Cu_0.6+xMn_1.68−xO₄ (0 < x < 0.6) spinel was fabricated at 600 °C using a low-temperature solution technique. The binding energy of the 2p_3/2 level of copper (930.8 eV) is found 1.9 eV lower than that of Cu⁰ (932.7 eV). XPS and EXAFS studies revealed that the post-thermal annealing between 600 and 800 °C undergoes an irreversible cubic-to-tetragonal phase transformation through oxidation–reduction reaction Cu¹⁺ + Mn⁴⁺  Cu²⁺ + Mn³⁺, and only tetrahedral Cu¹⁺ species in the cubic spinel shows this anomalous chemical shift. The negative shift of the core levels was correlated to an equal shift of the Cu 3d valence band levels. XPS valence bands from the samples annealed at different temperatures were compared to DOS calculations. The DOS computations were performed with FEFF-8.1 code using experimental crystal parameters established by the EXAFS analysis. It was found that the tetrahedral Cu¹⁺ in the 600 °C annealed sample exhibits localization of the 3d orbitals showing behavior characteristic to zinc. The completely filled and isolated 3d electron shell appears as a false valence band edge in the XPS spectrum. The position of the Cu 3d, and other core levels, is established by oxygen pinning the Cu valence band levels and by the fixed value of the p–d gap characteristic to the tetrahedral copper environment in this spinel.     

RF-sputtered CrB2 diffusion barrier for Ni/Au Ohmic contacts on p-CuCrO2

Ohmic contacts to p-type CuCrO₂ using Ni/Au/CrB₂/Ti/Au contact metallurgy are reported. The samples were annealed in the 200–700 °C range for 60 s in flowing oxygen ambient. A minimum specific contact resistance of 2 × 10⁻⁵ Ω cm² was obtained after annealing at 400 °C. Further increase in the annealing temperature (>400 °C) resulted in the degradation of contact resistance. Auger Electron Spectroscopy (AES) depth profiling showed that out-diffusion of Ti to the surface of the contact stacks was evident by 400 °C, followed by Cr at higher temperature. The CrB₂ diffusion barrier decreases the specific contact resistance by almost two orders of magnitude relative to Ni/Au alone.     

Luminescence from γ-irradiated humic acid

This study was conducted to investigate the ultraweak delayed radiochemiluminescence (RCL) spectra, kinetics and spectroscopic properties of humic acids (HAs) after γ-radiation exposure (absorbed doses of 1−10 kGy, Co-60) in model systems.

The kinetics and spectral distribution of RCL (340–650 nm) were measured using the single photon counting (SPC) method and cut-off filters.

The intensity of fluorescence (λ_ex=390, 440, 490 and 540 nm) covering the spectral range 400–580 nm was heavily dependent on the λ_ex and slightly increased with the absorbed dose of γ-radiation.

Absorption spectra (the range 240−800 nm) and color coefficients E_2.6/4 and E_4/6 of irradiated solutions indicated that post-radiative degradation/polymerization processes take place in the HA, changing their macromolecule size or properties.

Comparison of FTIR spectra and elemental analysis proved an increased O and decreased C atoms in irradiated samples. The data indicate on the radiolysis-induced degradation of native HA into fulvic-like acids with higher hydrophilicity and lower molecular size.     

Defect versus nanocrystal luminescence emitted from room temperature and hot-implanted SiO2 layers

Silicon nanocrystals have been synthesized in SiO₂ matrix using Si ion implantation. Si ions were implanted into 300-nm-thick SiO₂ films grown on crystalline Si at energies of 30–55 keV, and with doses of 5×10¹⁵, 3×10¹⁶, and 1×10¹⁷ cm⁻². Implanted samples were subsequently annealed in an N₂ ambient at 500–1100°C during various periods. Photoluminescence spectra for the sample implanted with 1×10¹⁷ cm⁻² at 55 keV show that red luminescence (750 nm) related to Si-nanocrystals clearly increases with annealing temperature and time in intensity, and that weak orange luminescence (600 nm) is observed after annealing at low temperatures of 500°C and 800°C. The luminescence around 600 nm becomes very intense when a thin SiO₂ sample is implanted at a substrate temperature of 400°C with an energy of 30 keV and a low dose of 5×10¹⁵ cm⁻². It vanishes after annealing at 800°C for 30 min. We conclude that this luminescence observed around 600 nm is caused by some radiative defects formed in Si-implanted SiO₂.     

An evaluation of surface properties and frictional forces generated from Al–Mo–Ni coating on piston ring

Surface properties of the Al–Mo–Ni coating plasma sprayed on the piston ring material and the frictional forces obtained by testing carried out under different loads, temperatures and frictional conditions were evaluated.

Al–Mo–Ni composite material was deposited on the AISI 440C test steel using plasma spraying method. The coated and uncoated samples were tested by being exposed to frictional testing under dry and lubricated conditions. Test temperatures of 25, 100, 200, and 300 °C and loads of 83, 100, 200, and 300 N were applied during the tests in order to obtain the frictional response of the coating under conditions similar to real piston ring/cylinder friction conditions. Gray cast iron was used as a counterface material. All the tests were carried out with a constant sliding speed of 1 m/s.

The properties of the coating were determined by using EDX and SEM analyses. Hardness distribution on the cross-section of the coating was also determined. In addition, the variations of the surface roughness after testing with test temperatures and loads under dry and lubricated conditions were recorded versus sliding distance.

It was determined that the surface roughness increased with increasing loads. It increased with temperature up to 200 °C and then decreased at 300 °C under dry test conditions.

Under lubricated conditions, the roughness decreased under the loads of 100 N and then increased. The roughness decreased at 200 °C but below and above this point it increased with the test temperature.

Frictional forces observed under dry and lubricated test conditions increased with load at running-in period of the sliding. The steady-state period was then established with the sliding distance as a normal situation. However, the frictional forces were generally lower at a higher test temperature than those at a lower test temperature. Surprisingly, the test temperature of 200 °C was a critical point for frictional forces and surface roughness.     

Structural properties of diamond fine particles and clusters prepared by detonation and decomposition of TNT

The thermal parameter B for three different particle sizes of diamond samples (bulk powder 1–4 μm, fine particle 144–195 Å and cluster 55–61 Å) was determined by the grazing incidence X-ray diffraction method. The values of B were found to be in the range 0.50–0.70 Å² for particles in the size range 195–55 Å and 0.27 Å² for 1–4 μm. All of them are larger than that of diamond bulk. A clear size dependence of B, increasing with decreasing particle size, was found. By analysing X-ray diffraction data at several temperatures the magnitude of B was found to be due to B_S (static part) instead of B_T (dynamic part). The average B_S values obtained were 0.04 Å², 0.19 Å² and 0.27 Å² for bulk powder, fine particle and cluster samples respectively. Ultrahigh resolution transmission electron microscope (TEM) observation confirmed the presence of strain, distortion, roughness and dislocation lines in many particles. TEM images of particles indicate that the clusters were not spherical in shape; they were mostly cubiform and some were truncated prism-like polyhedral. The present study reveals that the B_S component is responsible for the large B value in diamond fine particles and clusters. No clear surface local atomic distortion was found in the particles.     

Effect of oxide thickness on the capacitance and conductance characteristics of MOS structures

In this work, the investigation of the interface states density and series resistance from capacitance–voltage (C–V) and conductance–voltage (G–V) characteristics in Au/SnO₂/n-Si (MOS) structures prepared at various SnO₂ layer thicknesses by spray deposition technique have been reported. It is fabricated five samples depending on deposition time. The thicknesses of SnO₂ films obtained from the measurement of the oxide capacitance in the strong accumulation region for MOS Schottky diodes are 37, 79, 274, 401, and 446 Å, for D1, D2, D3, D4, and D5 samples, respectively. The C–V and G–V measurements of Au/SnO₂/n-Si MOS structures are performed in the voltage range from −6 to +10 V and the frequency range from 500 Hz to 10 MHz at room temperature. It is observed that peaks in the forward C–V characteristics appeared because of the series resistance. It has been seen that the value of the series resistance R_s of samples D1 (47 Ω), D2 (64 Ω), D3 (98 Ω), D4 (151 Ω), and D5 (163 Ω) increases with increasing the oxide layer thickness. The interface state density D_it ranges from 2.40×10¹³ cm⁻² eV⁻¹ for D1 sample to 2.73×10¹² cm⁻² eV⁻¹ for D5 sample and increases with increasing the oxide layer thickness.     

The effect of annealing under hydrostatic pressure on the visible photoluminescence from si-ion implanted SiO2 films

We have studied the influence of the hydrostatic pressure during annealing on the intensity of the visible photoluminescence (PL) from thermally grown SiO₂ films irradiated with Si⁺ ions. Post-implantation anneals have been carried out in an Ar ambient at temperatures T_a of 400°C and 450°C for 10 h and 1130°C for 5 h at hydrostatic pressures of 1 bar–15 kbar. It has been found that the intensity of the 360, 460 and 600 nm PL peaks increases with rising hydrostatic pressure during low-temperature annealing. The intensity of the short-wavelength PL under conditions of hydrostatic pressure continues to rise even at T_a=1130°C. Increasing T_a leads to a shift in the PL spectra towards the ultraviolet range. The results obtained have been interpreted in terms of enhanced, pressure-mediated formation of ≡Si–Si≡ centres and small Si clusters within metastable regions of the ion-implanted SiO₂.     

基于近红外光谱技术的紫外光老化落叶松木材表面材色变化的定性和定量研究

自然光中的紫外光在木材表面产生复杂的光化学反应,是木材在自然环境中老化降解速度最快,反应最强的化学过程。基于近红外光谱(NIRs)技术探讨了落叶松表面材色在340 nm波长紫外光照射条件下的老化状况。不同时间(180,540,900,1 080 h)试材弦切面经紫外光人工老化后,测量木材表面材色色度学指数,并采集NIRs信息。由NIRs二阶导数及其差谱图反映的信息,定性分析和讨论了木材表面化学组分基团的变化;定量建立基于偏最小二乘法(PLS)结合留一交叉验证的木材表面材色预测模型。结果表明：(1) 随着人工老化时间延长,木材表面明度值L*降低,红绿指数a*与黄蓝指数b*出现先增加后缓慢降低的趋势,表明发色基团的形成随着紫外光照射时间的延长而减少,在辐射时间540 h达到最大值,此外,色差值ΔE*与紫外光照射时间成正相关。(2) NIRs二阶导数在6 996,6 773以及6 287 cm-1等分别反映木材中纤维素非结晶区、半结晶区和结晶区的光谱吸光度随着老化时间的延长而增加,而5 986 cm-1反映木质素特征性谱带吸收峰随着紫外光老化时间的延长而降低,表明木质素出现降解。通过紫外光照射1 080 h与对照材的差谱分析发现,纤维素和半纤维素基团的特征峰差谱值为正,表明紫外光辐射后木材表面的纤维素和半纤维素相对含量增加,而木质素基团特征峰差谱值为负,表明经紫外光辐射后,木质素的降解导致其相对含量减少。这些结果与色度值测量结果相一致。(3) 基于NIRs建立的紫外光照射落叶松表面材色预测模型中,L*交叉验证模型决定系数(R2)为0.949,相对分析误差(RPD)为4.42;a*交叉验证模型R2是0.928,RPD是3.73;b*的交叉验证模型R2是0.831,RPD为2.43,建立的材色预测模型满足预测要求。     

Synthesis and physical behaviour of In2S3 films

In₂S₃ layers have been grown by close-spaced evaporation of pre-synthesized In₂S₃ powder from its constituent elements. The layers were deposited on glass substrates at temperatures in the range, 200–350 °C. The effect of substrate temperature on composition, structure, morphology, electrical and optical properties of the as-grown indium sulfide films has been studied. The synthesized powder exhibited cubic structure with a grain size of 63.92 nm and S/In ratio of 1.01. The films grown at 200 °C were amorphous in nature while its crystallinity increased with the increase of substrate temperature to 300 °C. The films exhibited pure tetragonal β-In₂S₃ phase at the substrate temperature of 350 °C. The surface morphological analysis revealed that the films grown at 300 °C had an average roughness of 1.43 nm. These films showed a S/In ratio of 0.98 and a lower electrical resistivity of 1.28 × 10³ Ω cm. The optical band gap was found to be direct and the layers grown at 300 °C showed a higher optical transmittance of 78% and an energy band gap of 2.49 eV.     

Surface diffusion of dysprosium on the W(1 1 1) facet

Diffusion of dysprosium on the (1 1 1) facet of a tungsten micromonocrystal was investigated by means of spectral analysis of field emission current fluctuations. The experimental spectral density functions of the current fluctuations were analysed by using Gesley and Swanson’s theoretical spectral density function, which enables to determine the surface diffusion coefficient D for dysprosium. Derived from the temperature dependence of D, the diffusion activation energy E is presented for some Dy coverages θ_(1 1 1). In the temperature range 400–600 K, the E first drops from 1.25 eV per atom at θ₍₁₁₁₎≈0.25 ML to 0.48 eV per atom at θ₍₁₁₁₎≈1 ML (corresponding to the minimum of the work function of the system), then increases to 1.03 eV per atom at θ₍₁₁₁₎≈1.3 ML. The results are discussed from the aspects of the substrate structure and interaction in the adsorbed layer.     

A study on the reaction between chlorine trifluoride gas and glass-like carbon

The reaction between glass-like carbon (GC) and chlorine trifluoride (ClF₃) gas was investigated with weight measurements, surface analysis, and gas desorption measurements, where the ClF₃ gas is used for the in situ cleaning of tubes in silicon-related fabrication equipment. From Auger electron spectroscopy and X-ray photoelectron spectroscopy measurements, a carbon mono-fluoride, –(CF)_n–, film near the surface of GC is considered to be grown onto the GC surface above 400 °C by the chemical reaction with ClF₃, and this thickness of the fluoride film depends on the temperature. The grown fluoride film desorbs by annealing in a vacuum up to 600 °C. Although GC is apparently etched by ClF₃ over 600 °C, the etch rate of GC is much lower than that of SiC and quartz.     

Kinetic aspects of aluminium titanate layer formation on titanium alloys by plasma electrolytic oxidation

The paper reports on a systematic investigation into the effects of process parameters on the growth kinetics and associated changes in the structure, phase composition and mechanical properties of surface layers formed on Ti–6Al–4V alloy by plasma electrolytic oxidation (PEO) treatment in 0.05–0.2 mol l⁻¹ solutions of sodium aluminate. Methods of gravimetric, SEM and XRD analysis, as well as microhardness and scratch testing, are employed to investigate mass transfer and phase-structure transformations in the surface layer. The probable mechanisms of layer formation are discussed, which comprise electrochemical oxidation of the Ti-electrode by OH⁻ anions, complimented by chemical precipitation of Al(OH)₃ and plasma-induced transformations in the surface discharges. Running with a total yield efficiency of 20–30%, these processes lead to the formation of predominantly the Al₂TiO₅ phase with heterogeneous precipitation of Al₂TiO₅·TiO₂ and 3Al₂TiO₅·Al₂O₃ eutectics. Al- and Ti-enriched constituents of this structure show hardnesses of 1050–1480 and 300–845 H_K, 0.02, respectively. The layer growth rate increases with increasing electrolyte concentration, providing a maximum thickness of over 60 μm and a surface roughness (R_a) of 3–4 μm. Increasing the electrolyte pH from 12.0 to 12.8 results in smoothing and thickening of the surface layer but a lower sample weight gain, associated with an enhancement of the Ti electro-oxidation process. Morphological changes during PEO formation of the surface layer include gradual transformation of the original fine grained but porous structure into a dense, fused morphology which is adversely affected by discharge-induced thermal stresses, causing a degradation of the layer adhesion strength.     

Far-infrared and millimeter wave spectroscopy of superionic copper conductors

Far-infrared and millimeter wave spectra of copper ion conducting crystal RbCu₄Cl_3+xI_2−x, which has the same structure as the room temperature silver ion conductor RbAg₄I₅, were investigated. Broad absorption peaks observed around 40, 80, and 110–200 cm⁻¹ at room temperature show doublet structures at low temperature; this may be attributed to the difference of local structure by chlorine and iodine ion. The 110–200 cm⁻¹ bands seem to be symmetric breathing modes of CuX₄ (X = Cl or I) tetrahedron and the frequency shift coincides with the square root of the mass ratio of conduction ions. The 80 cm⁻¹ band seems to be Rb-X vibration in RbX₆ octahedron. The 40 cm⁻¹ band seems to be the attempt mode which is an outward motion of the mobile ion in halogen cage. The increase of the absorption intensity at the low energy side with temperature corresponds to an increase of the DC conductivity. Plasmon fitting in energy loss function spectra was attempted.     

New red Y0.85Bi0.1Eu0.05V1−yMyO4 (M=Nb, P) phosphors for light-emitting diodes

The Y_0.85Bi_0.1Eu_0.05V_1−yM_yO₄ (M=Nb, P) as new near-ultraviolet excited phosphors were synthesized and their luminescence properties under 365 nm excitation were investigated in detail. It indicated that by doping small amount of P⁵⁺ into V⁵⁺ sites, the excitation intensity of charge transfer (CT) band of Bi–O (330–400 nm) was greatly improved. By substituting Nb⁵⁺ for V⁵⁺, both the CT bands of Bi–O and Eu–O (240–320 nm) were significantly enhanced. As a result, the emission intensity of Y_0.85Bi_0.1Eu_0.05V_1−yM_yO₄ (M=Nb, P) could be improved about 90% by doping 5 mol% P⁵⁺ and 110% by doping 5 mol% Nb⁵⁺. Comparing with the commercial Y₂O₂S:Eu³⁺ phosphors, the Y_0.85Bi_0.1Eu_0.05V_0.95M_0.05O₄ (M=Nb, P) phosphors exhibited excellent color purity and much higher brightness. The results showed that these Y_0.85Bi_0.1Eu_0.05V_1−yM_yO₄ (M=Nb, P) phosphors could be considered as promising red phosphors for application in LED.     

Chemical and structural modifications of laser treated iron surfaces: investigation of laser processing parameters

This study focuses on the chemical, morphological and structural characterization of iron surfaces treated by laser in ambient air. Incorporation of nitrogen over a 1–2 μm thickness (10–30 at.% at the profile maximum) and superficial oxidation on 200–400 nm depth have been evidenced by nuclear reaction analyses. X-ray diffraction at grazing incidence has shown the formation of FeO and Fe₃O₄ oxide phases as well as γ-Fe(N), and ε-Fe_xN for a sufficiently high amount of nitrogen incorporated. Treatments performed with different laser beams indicate that the parameter playing the major role in surface modification processes is the wavelength. Nitrogen incorporation has been found to occur via the interaction of reactive N, present in the laser-induced plasma, and the iron molten bath. The nitriding process is promoted in the IR wavelength range. Oxidation takes place by chemical reaction during the cooling step, and is furthered in the case of UV treatment.     

Thermal stability of the structural features in the superhydrophobic boehmite films on austenitic stainless steels

Boehmite thin film with 50–100 nm surface flake structure has been synthesized on AISI 316 type austenitic stainless steel by immersing boehmite gel film into boiling water. When further coated with hydrolyzed (heptadecafluoro-1,1,2,2-tetrahydrodecyl) trimethoxysilane (FAS), the boehmite film becomes superhydrophobic with a contact angle for water of 152°. The superhydrophobic property results from both the nanoscale surface flake structure and the low surface energy of the FAS top layer. The topography of such film was revealed by atomic force microscope (AFM) and a set of roughness parameters of such film was discussed. The degradation of superhydrophobicity of the surface was studied as a function of the heat-treatment temperatures. Below 600 °C, the surface remained to be superhydrophobic with the FAS top layer. Above 700 °C, the surface was not superhydrophobic anymore due to a gradual loss in surface roughness which was revealed by field emission scanning electron microscope (FESEM). A phase change from boehmite to γ-Al₂O₃ occurred during the heat-treatments from 700 to 900 °C which was studied by the selected area electron diffraction (SAED) patterns from the transmission electron microscope (TEM) measurement.