Effect of accelerated weathering on surface chemistry of modified wood

In this study, the effects of UV-light irradiation and water spray on colour and surface chemistry of scots pine sapwood samples were investigated. The specimens were treated with chromated copper arsenate (CCA), a metal-free propiconazol-based formulation, chitosan, furfuryl alcohol and linseed and tall oils. The weathering experiment was performed by cycles of 2 h UV-light irradiation followed by water spray for 18 min. The changes at the surface of the weathered samples were characterised by Fourier transform infrared spectroscopy (FT-IR); colour characterizations were performed by measuring CIELab parameters.The results show that all treatment methods except chitosan treatment provided lower colour changes than the control groups after 800 h exposure in weathering test cycle, but differences between chitosan and control were also small. The lowest colour changes were found on linseed oil (full cell process) and CCA treated wood. FT-IR results show that oil treatment (linseed and tall oil) decreased the intensities of a lignin specific peak (1500-1515 cm⁻¹). Absorption band changes at 1630-1660 cm⁻¹ were reduced by all treatments.     

Composition influence of SiNx gate insulator fabricated by radio frequency (RF) Magnetron sputtering on characteristics of organic thin-film transistors

To investigate the effect of composition of SiNx on the properties of organic thin-film transistors (OTFTs), we fabricated bottom gate top contact OTFTs devices with different composition SiNx gate insulator. Pentacene based OTFTs with SiNx insulator, prepared using an interface modification process of UV-ozone treatment, exhibited effective mobility of 0.63 cm2/Vs and on/off current ratio of 10⁵. Overall improvement in field-effect mobility, threshold voltage was observed as silicon content in SiNx increases. The results demonstrate that the viability of using SiNx for OTFTs and of UV-ozone treatment could be used to improve the properties of organic thin-film transistors. The dependence of the contact angle on the SiNx film composition is evident for the untreated samples, the contact angle increases as the silicon content in the untreated nitride film increases. In contrast, the rise in contact angle across all samples after surface treatment signifies effective surface modification to promote hydrophobicity of the nitride surface. The hydrophobic surface is needed for the organic semiconductor.     

Synthesis and characterization of silicon carbonitride films by plasma enhanced chemical vapor deposition (PECVD) using bis(dimethylamino)dimethylsilane (BDMADMS), as membrane for a small molecule gas separation

Silicon carbonitride thin films have been deposited by plasma enhanced chemical vapor deposition (PECVD) from bis(dimethylamino)dimethylsilane (BDMADMS) as a function of X = (BDMADMS/(BDMADMS + NH₃)) between 0.1 and 1, and plasma power P (W) between 100 and 400 W. The microstructure of obtained materials has been studied by SEM, FTIR, EDS, ellipsometrie, and contact angle of water measurements. The structure of the materials is strongly depended on plasma parameters; we can pass from a material rich in carbon to a material rich in nitrogen. Single gas permeation tests have been carried out and we have obtained a helium permeance of about 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ and ideal selectivity of helium over nitrogen of about 20.     

Oxygen plasma functionalization of poly(p-phenilene sulphide)

Surface effects during plasma activation of poly(p-phenilene sulphide)—PPS have been studied. Samples that were exposed to weakly ionized highly dissociated oxygen plasma created an inductively coupled radiofrequency discharge with the power of 100 W. The electron density and temperature were measured with a double Langmuir probe and were 4 × 10¹⁵ m⁻³ and 3 eV, respectively, while the neutral atom density was measured with a fiber optics catalytic probe and was 4 × 10²¹ m⁻³. The surface tension was determined by measuring the contact angle of deionized water, while the appearance of surface functional groups was detected by XPS. The surface tension of untreated PPS was 7 × 10⁻³ N/m or/and increased to 7 × 10⁻² N/m in few seconds of plasma treatment. It remained fairly constant for longer plasma treatments. The XPS survey spectrum showed little oxygen on untreated samples, but its concentration increased to about 20 at.% in few seconds. Detailed high resolution XPS C 1s peak showed that the carbon was left fairly stable during plasma treatment. The main functional groups formed were rather sulphate in sulphite groups, as determined from high resolution S 2p peak. Namely, a strong transition from sulphide to sulphate state of sulfur was observed. The spontaneous deactivation of the polymer surface was measured as well. The deactivation was fairly logarithmic with the characteristic decay time of several hours.     

Influence of ionic liquids on the surface properties of poplar veneers

In this paper, the influence of four types of imidazolium-based ionic liquids (ILs) on the surface properties of common aspen (Populus tremula) veneers has been studied by using contact angle, electrical conductivity and Fourier transform infrared spectroscopy analysis. The measurements showed that wood wettabillity is increased by IL treatment. The electrical conductivities of treated wood were in the 0.5-1 mS/cm range, higher than the ones reported in the reference literature. It has been determined that the ILs decrease the crystallinity and improve the flexibility of the cellulose matrix. It has been determined by photographic image analysis that the surface roughness of the IL treated veneers decreases in comparison with the untreated samples.     

Surface roughness and color characteristics of wood treated with preservatives after accelerated weathering test

Wood samples treated with ammonium copper quat (ACQ 1900 and ACQ 2200), chromated copper arsenate (CCA), Tanalith E 3491 and Wolmanit CX-8 have been studied in accelerated weathering experiments. The weathering experiment was performed by cycles of 2 h UV-light irradiation followed by water spray for 18 min. The changes on the surface of the weathered samples were characterized by roughness and color measurements on the samples with 0, 200, 400 and 600 h of total weathering.

The objective of this study was to investigate the changes created by weathering on impregnated wood with several different wood preservatives. This study was performed on the accelerated weathering test cycle, using UV irradiation and water spray in order to simulate natural weathering.

Surface roughness and color measurement was used to investigate the changes after several intervals (0–200–400–600 h) in artificial weathering of treated and untreated wood.     

Comparative study of the photo-discoloration of moso bamboo (Phyllostachys pubescens Mazel) and two wood species

Bamboo or bamboo products undergo surface degradation during outdoor exposure resulting in lower quality in service. In this study, the effect of UV-vis light irradiation on changes in color and surface chemistry of moso bamboo (Phyllostachys pubescens Mazel) was investigated. For comparison purpose, two wood species (a soft and a hardwood) were also studied to present their differences in degradation performance. Color characterization was performed by measuring CIELab parameters (L*, a*, b* and ΔE*), and Fourier transform infrared (FTIR) spectroscopy was used to analyze the chemical changes induced by irradiation. The results showed that the surface color of bamboo changed rapidly during the irradiation process. Compared with the wood species, bamboo was less influenced by photo-irradiation. Chemical analysis indicated that irradiation altered the chemical structures of bamboo surfaces. Lignin was the most sensitive component to photo-degradation and the intensities of its characteristics bands decreased significantly during the irradiation process. This was accompanied by formation of new carbonyl groups at 1735 cm⁻¹. The rate of lignin degradation and carbonyl formation in bamboo was relatively lower compared with the wood species. The color changes (ΔE*) was well correlated with lignin degradation and carbonyl formation regardless bamboo or the wood species.     

Improvement of organic solar cells by flexible substrate and ITO surface treatments

In this paper, surface treatments on polyethylene terephthalate with polymeric hard coating (PET-HC) substrates are described. The effect of the contact angle on the treatment is first investigated. It has been observed that detergent is quite effective in removing organic contamination on the flexible PET-HC substrates. Next, using a DC-reactive magnetron sputter, indium tin oxide (ITO) thin films of 90 nm are grown on a substrate treated by detergent. Then, various ITO surface treatments are made for improving the performance of the finally developed organic solar cells with structure Al/P3HT:PCBM/PEDOT:PSS/ITO/PET. It is found that the parameters of the ITO including resistivity, carrier concentration, transmittance, surface morphology, and work function depended on the surface treatments and significantly influence the solar cell performance. With the optimal conditions for detergent treatment on flexible PET substrates, the ITO film with a resistivity of 5.6 × 10⁻⁴ Ω cm and average optical transmittance of 84.1% in the visible region are obtained. The optimal ITO surface treated by detergent for 5 min and then by UV ozone for 20 min exhibits the best WF value of 5.22 eV. This improves about 8.30% in the WF compared with that of the untreated ITO film. In the case of optimal treatment with the organic photovoltaic device, meanwhile, 36.6% enhancement in short circuit current density (J_sc) and 92.7% enhancement in conversion efficiency (η) over the untreated solar cell are obtained.     

The wettability of polytetrafluoroethylene and polymethylmethacrylate by aqueous solutions of Triton X-100 and short chain alcohol mixtures

Measurements of advancing contact angles (θ) were carried out for aqueous solutions of Triton X-100 (TX-100) and methanol and ethanol mixtures at constant TX-100 concentration equal to 1 × 10⁻⁷, 1 × 10⁻⁶, 1 × 10⁻⁵, 1 × 10⁻⁴, 6 × 10⁻⁴ and 1 × 10⁻³ M, respectively, on polytetrafluoroethylene (PTFE) and polymethylmethacrylate (PMMA). Using measured contact angle values the relationships between cos θ, adhesion tension and surface tension of the solutions were determined, and on their basis the critical surface tension of PTFE and PMMA wetting was calculated. The obtained average value of the critical surface tension of PTFE wetting is lying in the range of the PTFE surface tension values which can be found in the literature, while for PMMA it is even lower than the Lifshitz-van der Waals component of its surface tension. From the relationship between the adhesion and surface tension and Lucassen-Reynders equation it results that in the case of PTFE the adsorption at the PTFE-solution and solution-air interfaces is the same, which was confirmed by a linear relationship between the cos θ and 1/γ_LV and intercept on cos θ axis equal to −1. However, for PMMA the adsorption of the surface active agents at solution-air interface is higher than at PMMA-solution. Using the values of the contact angle the values of the adhesion work of solution to the PTFE and PMMA surface were also determined, which are constant for PTFE, but for PMMA decrease with alcohol concentration increase. Next, using the contact angle values in the Young equation, the PTFE(PMMA)-solution interface tension was also calculated. The obtained values of PTFE-solution interface tension were compared with those evaluated from the Szyszkowski, Connors and Fainerman and Miller equations, and good agreement between these values was observed for all series of TX-100 and alcohol mixtures at a low alcohol concentration.     

Organic modification of TEOS based silica aerogels using hexadecyltrimethoxysilane as a hydrophobic reagent

The experimental results on the synthesis and characterization of tetraethoxysilane (TEOS) based hydrophobic silica aerogels using hexadecyltrimethoxysilane (HDTMS) as a hydrophobic reagent by two step sol-gel process, are described. The molar ratio of tetraethoxysilane (TEOS), methanol (MeOH), acidic water (0.001 M, oxalic acid) and basic water (10 M, NH₄OH) was kept constant at 1:55:3.25:1.25 and the molar ratio of HDTMS/TEOS (M) was varied from 0 to 28.5 × 10⁻². The organic modification was confirmed by infrared spectroscopic studies, and the hydrophobicity of the aerogels was tested by the contact angle measurements. The maximum contact angle of 152° was obtained for M = 22.8 × 10⁻². The aerogels retained the hydrophobicity up to a temperature of 240 °C and above this temperature the aerogels became hydrophilic. The aerogels were characterized by the thermal conductivity, density, contact angle measurements, optical transmission and scanning electron micrographs.     

Electrical, structural and surface morphological properties of thermally stable low-resistance W/Ti/Au multilayer ohmic contacts to n-type GaN

A W/Ti/Au multilayer scheme has been fabricated for achieving thermally stable low-resistance ohmic contact to n-type GaN (4.0 × 10¹⁸ cm⁻³). It is shown that the as-deposited W/Ti/Au contact exhibits near linear I-V behaviour. However, annealing at temperature below 800 °C the contacts exhibit non-linear behaviour. After annealing at a temperature in excess of 850 °C, the W/Ti/Au contact showed ohmic behaviour. The W/Ti/Au contact produced specific contact resistance as low as 6.7 × 10⁻⁶ Ω cm² after annealing at 900 °C for 1 min in a N₂ ambient. It is noted that the specific contact resistance decreases with increase in annealing temperature. It is also noted that annealing the contacts at 900 °C for 30 min causes insignificant degradation of the electrical and thermal properties. It is further shown that the overall surface morphology of the W/Ti/Au stayed fairly smooth even after annealing at 900 °C. The W/Ti/Au ohmic contact showed good edge sharpness after annealing at 900 °C for 30 min. Based on the Auger electron spectroscopy and glancing angle X-ray diffraction results, possible explanation for the annealing dependence of the specific contact resistance of the W/Ti/Au contacts are described and discussed.     

Electrochemical synthesis of poly-6-amino-m-cresol (poly-AmC)

The electropolymerization of 6-amino-m-cresol (AmC) on a platinum electrode was studied in 0.1 M Na₂SO₄ solution containing 5 × 10⁻³ M 6-amino-m-cresol at different pHs using cyclic voltammetry technique. Voltammetric results showed that oxidation of 6-amino-m-cresol produced a passivating polymeric film on the platinum surface at all pHs studied. Synthesized polymer has bronze color on platinum. To investigate the structure of poly-6-amino-m-cresol (poly-AmC) films FTIR technique was employed. The spectroscopic results indicate that polymer chain consist of ring opened units rather than phenoxazine structure.     

Effects of surface inactivation, high temperature drying and preservative treatment on surface roughness and colour of alder and beech wood

Although extensive research has been conducted in wood surface quality analysis, a unified approach to surface quality characterisation does not exist. Measurements of the variation in surface roughness and surface colour are used widely for the evaluation of wood surface quality. Colour is a basic visual feature for wood and wood-based products. Colour measurement is one of the quality control tests that should be carried out because the colour deviations are spotted easily by the consumers. On the other hand, a common problem faced by plywood manufacturers is panel delamination, for which a major cause is poor quality glue-bonds resulting from rough veneer. Rotary cut veneers with dimensions of 500 mm × 500 mm × 2 mm manufactured from alder (Alnus glutinosa subsp. barbata) and beech (Fagus orientalis Lipsky) logs were used as materials in this study. Veneer sheets were oven-dried in a veneer dryer at 110 °C (normal drying temperature) and 180 °C (high drying temperature) after peeling process. The surfaces of some veneers were then exposed at indoor laboratory conditions to obtain inactive wood surfaces for glue bonds, and some veneers were treated with borax, boric acid and ammonium acetate solutions. After these treatments, surface roughness and colour measurements were made on veneer surfaces. High temperature drying process caused a darkening on the surfaces of alder and beech veneers. Total colour change value (ΔE^*) increased linear with increasing exposure time. Among the treatment solutions, ammonium acetate caused the biggest colour change while treatment with borax caused the lowest changes in ΔE^* values. Considerable changes in surface roughness after preservative treatment did not occur on veneer surfaces. Generally, no clear changes were obtained or the values mean roughness profile (R_a) decreased slightly in R_a values after the natural inactivation process.     

Hydrophobic modification of wood via surface-initiated ARGET ATRP of MMA

To convert the hydrophilic surface of wood into a hydrophobic surface, the present study investigated activators regenerated by electron transfer for atom transfer radical polymerization (ARGET ATRP) as a method of grafting methyl methacrylate (MMA) onto the wood surface. The wood treated with 2-bromoisobutyryl bromide and with the subsequently attached MMA via ARGET ATRP under different polymerization times (2 h, 4 h, 6 h, 8 h) were examined using scanning electron microscopy, Fourier transform infrared spectroscopy, and thermogravimetric analysis. All the analyses confirmed that PMMA had been grafted onto the wood surface. Water contact angle measurement proved that the covering layer of PMMA on wood made the surface hydrophobic. Polymerization time had a positive influence on the contact angle value and higher contact angle can be produced with the prolongation of the polymerization time. When the reaction time was extended to 8 h, the contact angle of treated wood surface reached 130° in the beginning, and remained at 116° after 60 s. The ARGET ATRP method may raise an alteration on the wood surface modification.     

Effect of plasma pretreatment on adhesion and mechanical properties of UV-curable coatings on plastics

An attempt was made to study the effect of plasma surface activation on the adhesion of UV-curable sol-gel coatings on polycarbonate (PC) and polymethylmethacrylate (PMMA) substrates. The sol was synthesized by the hydrolysis and condensation of a UV-curable silane in combination with Zr-n-propoxide. Coatings deposited by dip coating were cured using UV-radiation followed by thermal curing between 80 °C and 130 °C. The effect of plasma surface treatment on the wettability of the polymer surface prior to coating deposition was followed up by measuring the water contact angle. The water contact angle on the surface of as-cleaned substrates was 80° ± 2° and that after plasma treatment was 43° ± 1° and 50° ± 2° for PC and PMMA respectively. Adhesion as well as mechanical properties like scratch resistance and taber abrasion resistance were evaluated for coatings deposited over plasma treated and untreated surfaces.     

Studies on surface graft polymerization of acrylic acid onto PTFE film by remote argon plasma initiation

The graft polymerization of acrylic acid (AAc) was carried out onto poly(tetrafluoroethylene) (PTFE) films that had been pretreated with remote argon plasma and subsequently exposed to oxygen to create peroxides. Peroxides are known to be the species responsible for initiating the graft polymerization when PTFE reacts with AAc. We chose different parameters of remote plasma treatment to get the optimum condition for introducing maximum peroxides (2.87 × 10⁻¹¹ mol/cm²) on the surface. The influence of grafted reaction conditions on the grafting degree was investigated. The maximum grafting degree was 25.2 μg/cm². The surface microstructures and compositions of the AAc grafted PTFE film were characterized with the water contact angle meter, Fourier-transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). Contact angle measurements revealed that the water contact angle decreased from 108° to 41° and the surface free energy increased from 22.1 × 10⁻⁵ to 62.1 × 10⁻⁵ N cm⁻¹ by the grafting of the AAc chains. The hydrophilicity of the PTFE film surface was greatly enhanced. The time-dependent activity of the grafted surface was better than that of the plasma treated film.     

Weathering properties of treated southern yellow pine wood examined by X-ray photoelectron spectroscopy, scanning electron microscopy and physical characterization

In this study the weathering behavior of southern yellow pine (SYP) wood samples pretreated in different solutions has been examined using X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and various types of physical characterization regarding material loss and discoloration. The treatment solutions include water as a control, a commercially available water repellent (WR) wood treating additive and polyethylene glycol (PEG) products including PEG PLUS™, PEG 8000 solutions and Compound 20M in varying concentrations. All contained the wood preservative chromated copper arsenate (CCA). One sample was treated with a CCA solution only. The treatments were carried out at 20 °C and 150 psig for 1/2 h after exposure to vacuum (28 mmHg) for 15 min. Simulated weathering was achieved in an Atlas 65-W Weather-Ometer for 2000 h with both light and dark periods and rain. The temperature ranged from 23 °C during the dark cycle to 35 °C during the light cycle. With weathering the XPS O/C ratios increase due to oxidation of the surface. Exposure to UV light results in bond breakage and reaction with oxygen in the presence of air to form organic functional groups such as , , CO and/or O-C-O. These oxidized products can protect the underlying wood from deterioration if they are insoluble in water and remain on the surface as a protective coating. If soluble, rain washes the compounds away and assists in the degradation. Correlated changes are observed in the XPS O/C ratios, the high-resolution XPS C 1s spectra, the SEM micrographs and physical measurements including thickness alteration, weight loss, and discoloration by yellowing or whitening of the weathered wood. The PEG treatments are effective in protecting wood with the 2% PEG PLUS treatment providing the best weathering behavior similar to that of the CCA treatment. The WR and water treatments yield the poorest weathering properties.     

Surface structures and osteoblast response of hydrothermally produced CaTiO3 thin film on Ti-13Nb-13Zr alloy

This study investigated the surface characteristics and in vitro biocompatibility of a titanium (Ti) oxide layer incorporating calcium ions (Ca) obtained by hydrothermal treatment with or without post heat-treatment in the Ti-13Nb-13Zr alloy. The surface characteristics were evaluated by scanning electron microscopy, thin-film X-ray diffractometry, X-ray photoelectron spectroscopy, atomic force microscopy and contact angle measurements. In vitro biocompatibility of the Ca-containing surfaces was assessed in comparison with untreated surfaces using a pre-osteoblast cell line. Hydrothermal treatment produced a crystalline CaTiO₃ layer. Post heat-treatment at 400 °C for 2 h in air significantly decreased water contact angles in the CaTiO₃ layer (p < 0.001). The Ca-incorporated alloy surfaces displayed markedly increased cell viability and ALP activity compared with untreated surfaces (p < 0.001), and also an upregulated expression of various integrin genes (α1, α2, α5, αv, β1 and β3) at an early incubation time-point. Post heat-treatment further increased attachment and ALP activity in cells grown on Ca-incorporated Ti-13Nb-13Zr alloy surfaces. The results indicate that the Ca-incorporated oxide layer produced by hydrothermal treatment and a simple post heat-treatment may be effective in improving bone healing in Ti-13Nb-13Zr alloy implants by enhancing the viability and differentiation of osteoblastic cells.     

Fluorination of polymethylmethaacrylate with tetrafluoroethane using DC glow discharge plasma

Fluorination of polymer surfaces has technological applications in various fields such as microelectronics, biomaterials, textile, packing, etc. In this study PMMA surfaces were fluorinated using DC glow discharge plasma. Tetrafluoroethane was used as the fluorinating agent. On the fluorinated PMMA surface, static water contact angle, surface energy, optical transmittance (UV-vis), XPS and AFM analyses were carried out. After the fluorination PMMA surface becomes hydrophobic with water contact angle of 107° without losing optical transparency. Surface energy of fluorine plasma-treated PMMA decreased from 35 mJ/cm² to 21.2 mJ/cm². RMS roughness of the fluorinated surface was 4.01 nm and XPS studies revealed the formation of C-CF_x and CF₃ groups on the PMMA surface.     

A novel chemical synthesis and characterization of Mn3O4 thin films for supercapacitor application

Mn₃O₄ thin films have been prepared by novel chemical successive ionic layer adsorption and reaction (SILAR) method. Further these films were characterized for their structural, morphological and optical properties by means of X-ray diffraction (XRD), Fourier transform infrared spectrum (FTIR), field emission scanning electron microscopy (FESEM), wettability test and optical absorption studies. The XRD pattern showed that the Mn₃O₄ films exhibit tetragonal hausmannite structure. Formation of manganese oxide compound was confirmed from FTIR studies. The optical absorption showed existence of direct optical band gap of energy 2.30 eV. Mn₃O₄ film surface showed hydrophilic nature with water contact angle of 55°. The supercapacitive properties of Mn₃O₄ thin film investigated in 1 M Na₂SO₄ electrolyte showed maximum supercapacitance of 314 F g⁻¹ at scan rate 5 mV s⁻¹.