基于半导体光放大器的脉宽可调谐暗脉冲激光器

利用半导体光放大器(SOA)实现了一种脉宽可调谐的暗脉冲光纤激光器。将基于SOA的光纤激光器的一部分输出反馈注入SOA,由于SOA的非线性偏振旋转效应,输出脉冲经历不同的偏振演化,从而得到暗脉冲输出。通过改变反馈腔长度可以实现暗脉冲的脉宽调谐。分析了半导体光放大器的非线性偏振效应及暗脉冲的产生机理。并在实验中观察到了脉宽可调谐的暗脉冲输出。通过改变反馈腔长,在重复频率不变(11.31 MHz)的条件下,得到了脉宽为5.91~22.34 ns可调的暗脉冲。     

双脉冲电子直线感应加速器实验研究

 Mini-LIA为MHz重复频率双脉冲电子直线感应加速器,由双脉冲功率系统、热阴极电子枪注入器及金属玻璃磁芯感应加速腔等组成。在此平台的实验获得了数百ns间隔（即MHz重复频率）的双脉冲高压,每个脉冲幅值达到80 kV,脉冲半高全宽为80 ns;在感应腔加速间隙处测得双脉冲加速电场;在加速器出口处测量得到流强约1.1 A的双脉冲电子束流。实验结果表明：利用硅堆隔离汇流装置可实现MHz重复频率的双脉冲高压,金属玻璃磁芯感应加速腔和六硼化镧热阴极电子枪均适合MHz重复频率双脉冲工作方式。     

基于频移反馈腔的全光纤射频调制脉冲激光研究

射频调制的脉冲激光是激光雷达探测领域内的一项重要研究内容.根据声光斩波器的强度和频率调制特性,设计了基于频移反馈腔的全光纤射频调制脉冲激光.理论上,建立了基于频移反馈腔的激光外差相干理论模型,并进行了数值仿真.根据理论模型,实验上严格控制频移反馈腔的长度和声光斩波器触发信号的周期,在100 MHz的射频信号驱动下,产生了脉冲宽度110 ns、重复频率约20 kHz的具有最高700 MHz射频调制的脉冲激光(脉内调制激光);同时微调斩波周期可以实现脉冲前沿或后沿的多样性射频调制.通过改变反馈腔内光纤放大器的输出功率实现了射频调制深度的连续可调,最高达到了0.67.     

用光激开关产生一高功率亚纳秒电脉冲的研究

报道了用全固态绝缘结构研制的横向型半绝缘GaAs光电导开关产生高功率亚纳秒电脉冲的性能和测试结果.8mm电极间隙的开关暗态绝缘强度达30kV.分别用ns,ps和fs激光脉冲触发开关的测试表明,开关输出电磁脉冲无晃动.3mm电极间隙开关的最短电流脉冲上升时间小于200ps,脉宽达亚ns;在偏置电压2000伏,光脉冲宽度8ns,能量1.2mJ的触发条件下,峰值电流达560A.用重复频率为76MHz和108Hz的光脉冲序列触发开关也获得清晰的电流脉冲序列.     

用光激开关产生高功率亚纳秒电脉冲的研究

 报道了用全固态绝缘结构研制的横向型半绝缘GaAs光电导开关产生高功率亚纳秒电脉冲的性能和测试结果。8mm电极间隙的开关暗态绝缘强度达30kV。分别用ns, ps和fs激光脉冲触发开关的测试表明,开关输出电磁脉冲无晃动。3mm电极间隙开关的最短电流脉冲上升时间小于200ps,脉宽达亚ns;在偏置电压2000伏,光脉冲宽度8ns、能量1.2mJ的触发条件下,峰值电流达560A。用重复频率为76MHz和10⁸Hz的光脉冲序列触发开关也获得清晰的电流脉冲序列。     

脉冲单频Nd:YVO4激光器及其倍频输出特性研究

为了研制激光干涉成像所需的主振荡功率放大(MOPA)结构脉冲单频激光器,本文完成MOPA激光器的种子源即声光调Q脉冲单频1 064 nm激光器的特性研究,同时完成种子源腔外倍频绿光特性研究。脉冲单频激光器采用声光调Q模块实现脉宽约20 ns的1 064 nm脉冲激光输出,采用环形腔设计并采用一组不同厚度的标准具实现单纵模运转。实验研究基频1 064nm和倍频532 nm激光脉冲的线宽,得出在全脉宽范围内都具有较高时间相干性的结论。实验分别获得脉宽约28 ns峰值功率约6.5 kW的1 064 nm脉冲单频激光和脉宽约20 ns、峰值功率约0.5 kW的532 nm脉冲单频激光,腔外倍频效率为5.6%。实验同时也验证了腔外倍频的激光脉宽压缩效应。     

4MV/80kA IVA型脉冲X射线照相装置研制进展

介绍了西北核技术研究院研制的4 MV脉冲X射线闪光照相装置("剑光二号")系统组成和实验结果。装置基于感应电压叠加器(IVA)驱动阳极杆箍缩二极管(RPD)技术,主要由前级脉冲功率源、感应电压叠加器和RPD等组成。前级脉冲功率源由两台3.2 MV低电感Marx发生器和四路同轴水介质线组成。每台Marx同时给两路脉冲形成线(特征阻抗6Ω、电气长度30 ns)充电,充电峰值时间约370 ns。每路水介质线采用两级脉冲压缩,为感应腔馈入约1 MV/160 kA/60 ns电脉冲。电触发SF6气体开关、自击穿水开关分别用作主同步开关和脉冲陡化开关。感应电压叠加器采用四级1.5 MV感应腔串联,每级感应腔采用单点馈入结构。次级采用真空绝缘传输线实现电压叠加和功率传输,特征阻抗由30Ω线性增大至120Ω。采用4 MV电压下综合性能较优的RPD来产生强脉冲X射线。装置目前达到技术指标:输出电压4.3 MV、脉冲前沿(10%~90%)21 ns、半高宽约70 ns、二极管电流85 kA,X射线半高宽约55 ns,整机延时(从Marx触发器输出到X射线产生)约749 ns,标准偏差约7 ns。当RPD阳极采用直径2 mm钨针时,正前方1 m处剂量约15.5 rad(LiF),正向焦斑约1.4 mm。     

强耦合腔-QED系统中原子的纳秒脉冲激发光谱研究

本文在多原子强耦合腔-QED系统中,利用脉冲宽度为5 ns的强脉冲光在垂直于腔轴方向直接激发原子,脉冲的峰值功率为40 mW,通过光学腔观测激发原子辐射到腔中的光子获得相应的激发光谱。我们发现当光场频率和原子跃迁失谐±80 MHz时原子激发率达到最大,而在共振时原子激发被抑制。我们建立了脉冲光与三能级原子相互作用的模型,通过缀饰态能够解释此现象。     

三脉冲功率系统模块

采用基于并联Blumlein脉冲形成线的MHz重复频率脉冲功率技术和基于激光触发气体开关的多级触发系统,设计了脉冲功率系统模块,该模块具备6路输出能力,每路均可以MHz重复频率猝发方式输出三脉冲,幅度可达300 kV。对模块中的Blumlein装置、脉冲汇流、隔离网络、触发系统等部件参数进行了设计。以多脉冲直线感应加速器感应腔作为负载,对该模块的性能进行了分析,结果表明:模块中每个脉冲的输出时间抖动小于2.3 ns（标准差）,脉冲间最小时间间隔大于500 ns时可在负载上获得高品质波形。     

利用单模光纤中SBS效应进行被动调Q的掺铒光纤激光器研究

分析了利用光纤中的受激布里渊散射(SBS)相位共轭效应进行激光腔内调Q,产生ns量级脉冲激光的原理,并对利用该效应产生的激光脉冲波形和脉冲形成过程进行了数值模拟,得到的脉冲波形与SBS相位共轭反射率随时间变化曲线基本一致,表明利用光纤中的SBS相位共轭作用调Q具有可行性。据此,对采用单模光纤(SMF)作为SBS池的掺Er3＋调Q光纤激光器进行实验研究,当单模光纤长度为1.5 m时,在45 mW的抽运光功率下得到脉宽约2.6 ns,脉冲周期58.23 ns,平均功率7.35 mW的激光脉冲。进一步的研究表明：激光器中相位共轭镜的形成与SBS介质长度有关,SBS介质过长,斯托克斯线之间无固定的相位关系,不能形成相干叠加,SBS相位共轭腔不能形成; SBS介质过短,腔内正交偏振模光子寿命的改变使脉冲出现双峰现象。脉冲形成后其属性只与SBS动态属性有关。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.