1.6Cell光阴极微波电子枪冷测及初步高功率实验研究

介绍了清华大学加速器实验室BNL/KEK/SHI型1.6cell微波枪调谐以及老练的初步结果. 调谐过程中, 测量了耦合孔尺寸与外部品质因数之间的关系; 给出了0模和π模的频率、单腔频率以及场分布. 目前, 该微波电子枪正在进行高功率微波老练, 给出了该枪初步的微波老练的情况及测量结果.     

微脉冲电子枪的初步实验研究

给出了微脉冲电子枪的模拟计算及其初步实验结果. 该电子枪采用铜铝镁合金作为冷阴极材料, 在以磁控管作为微波功率源的出束实验中得到了100mA/cm²的电流密度.实验结果与次级电子倍增解析计算和SEEG程序的模拟计算结果基本符合, 初步验证了微脉冲电子枪的基本原理, 为今后实验中得到更大的电流密度打下了基础.     

大电流稳定发射铁电阴极的模拟与实验研究

讨论了铁电阴极的发射机理, 借助MAFIA对不同电极结构的铁电阴极表面电场分布进行了模拟计算. 计算中发现, 发射面电极结构对铁电阴极表面三界点处的场增强效应影响很大,特别是具有孤岛电极结构的铁电阴极具有更大的三界点场强,从而获得更大和更稳定的发射电流. 通过对电极结构及其工艺的改进,使用PLZT铁电阴极在实验中得到了大于100A的电流.     

返波型行波电子直线加速结构的理论研究

比较了行波与驻波两种工作方式以及前向波与返波型行波的不同特点;研究了返波型行波电子直线加速结构的工作特性;并针对返波型行波电子直线加速结构的特点,进行工作模式的选择;对工作频率为2856MHz,3π/4模的返波加速结构进行了优化设计;研究了带聚束段的返波型行波加速管的纵向与横向粒子动力学问题;为海关大型集装箱在线检测用加速器设计了一根9MeV返波型行波加速管,并与采用盘荷波导结构的加速管进行了对比.研究结果表明,返波型行波电子直线加速结构具有一定的优势,它把鼻锥型加速结构分流阻抗高及盘荷波导行波工作方式填充时间短,工作稳定性好等优点结合起来,性能明显优越.     

RF deflecting cavity design for bunch length measurement of photoinjector at Tsinghua University

RF deflecting cavity can be used for bunch length measurement and is designed to diagnose the beam produced by the photocathode electron gun which was built at Tsinghua University for the Thomson scattering experiment. Detailed discussion and calculation for measuring the 3.5 MeV bunch and another with further acceleration to 50 MeV, which is under development, are presented. A standing-wave deflecting cavity working at 2856 MHz is designed and the power feeding system has been planned.     

Tuning method for nonuniform traveling-wave accelerating structures

The tuning method of uniform traveling-wave structures based on the non-resonant perturbation field distribution measurement has been widely used in tuning both constant-impedance and constant-gradient structures. In this paper, the method of tuning nonuniform structures is proposed on the basis of the above theory. The internal reflection coefficient of each cell is obtained from analyzing the normalized voltage distribution. A numerical simulation of tuning process according to the coupled cavity chain theory has been done and the result shows each cell is in right phase advance after tuning. The method will be used in the tuning of a disk-loaded traveling-wave structure which is being developed at the Accelerator Laboratory, Tsinghua University.     

Design and cold test of a rectangular cavity beam position monitor

The CBPM is a kind of monitor which is used for the measurement of beam transverse position. It is becoming increasingly popular due to its high potential in resolution performance. In theory, the resolution can reach about 1 nanometer. In this paper, a rectangular CBPM is designed for it has better X-Y isolation than a cylindrical one. It has been simulated and measured, and the results agree with each other very well. The procedures and results for the simulation and the cold test will be shown later and it will be proved that this is a reliable method for the CBPM design.     

Simulation and experiments for the Q_ext of a cavity beam position monitor

The external Q (Qext) of the dipole mode is a key parameter of the Cavity Beam Position Monitor (CBPM). It determines the amplitude and length of the dipole mode signal. In this paper, Qext of a CBPM whose waveguides were open to the air was simulated and measured, and the results agreed with each other. Then four waveguide-to-coaxial cable adpaters were adjusted and assembled to the CBPM, and Qext remained unchanged. This progress provides a reliable method to evaluate Qext in the physics design without si...     

铁电阴极电子枪的初步实验研究

 设计加工了铁电阴极电子枪,给出了模拟计算及其初步实验结果。电子枪为皮尔斯枪型,采用顺电相陶瓷Ba0.67Sr0.33TiO₂作为铁电阴极材料,电子枪电压脉宽80 ns,幅值最大可达80 kV,设计电子枪导流系数为0.15×10^-6 A·V^-3/2。电子枪电压从30 kV逐步增大到56 kV,测量到其发射电流从0.7 A逐步增大到2.5 A。根据实验结果拟合得到的电子枪导流系数为0.2×10^-6 A·V^-3/2,与设计基本符合。     

Design and experiments for the waveguide to coaxial cable adapter of a cavity beam position monitor

The waveguide to coaxial cable adapter is very important to the cavity beam position monitor (CBPM) because it determines how much of the energy in the cavity could be coupled outside. In this paper, the waveguide to coaxial cable adapter of a CBPM is designed and experiments are conducted. The curve shapes of experiments and simulations are very similar and the difference in reflection is less than 0.1. This progress provides a reliable method for designing the adapter.