3D多孔FeC_2O_4/石墨烯电极用于高性能25 V水系非对称超级电容器（英文）

本文制备的三维多孔结构FeC_2O_4/石墨烯复合材料,在不添加粘结剂时可作为超级电容器电极.复合材料由大孔石墨烯和微介孔FeC_2O_4组成.通常,水分解电压为1.23 V,对于以水系为电解液的不对称超级电容器,电压窗口限制为2V.当以FeC_2O_4/rGO水凝胶作为负极,以纯rGO水凝胶作为正极时,在KOH(1.0mol/L)电解质中不对称超级电容器电压窗为1.7 V,在中性Na_2SO_4(1.0 mol/L)电解质中可达到2.5 V,相应地,组装的非对称电容器性能优异,能量密度为59.7 Wh/kg.通过将具有微介孔结构的金属氧化物与石墨烯相结合,制备在不添加导电剂和粘合剂时直接用于组装不对称超级电容器的电极材料.     

氧化还原可逆Nb2TiO7复合阴极电解池高温水蒸气电解研究

系统地研究Nb₂TiO₇与Nb_1.33Ti_0.67O₄材料相互转变的氧化还原循环可逆性能,同时研究Nb2TiO7和Nb_1.33Ti_0.67O₄样品随温度和氧分压变化的电导率,并与复合电极对称电池和电解池的电化学性能相关联. 在830 oC下,对Nb_1.33Ti_0.67O₄复合电极电解池进行水蒸气的电解研究测试. 电流电压曲线和电解池短期性能测试表明在低电压下主要为电极的还原和活化过程;而在高电压下主要为水蒸气的电解. 当3%H₂O/Ar/4%H_{2气体通入阴极时电解池水蒸气电解的法拉第效率为98.9%;而当通入气体转换为3%H2O/Ar时效率为89%.}     

“无水”NiCo2O4纳米棒在电化学无酶葡萄糖传感中的应用

本文介绍了棒状NiCo₂O₄的制备,并将其修饰玻碳电极作为无酶葡萄糖传感器. 通过简单的水热反应合成了NiCo₂O₄,然后在商用微波炉中对NiCo₂O₄进行处理,以消除水热合成过程中可能引入的残存水. 扫描电镜、透射电镜、X射线衍射谱和X射线光电子能谱分析表明,微波处理前后结构无变化. 通过EDS对Ni,Co,O原子比例的分析,证明微波处理对残存水的消除作用. 微波处理的NiCo₂O₄(M-NiCo₂O₄)作为葡萄糖传感器的灵敏度高达431.29 μA mM^-1 cm^-2. 最后,将M-NiCo₂O₄在水中浸泡不同时间后,其对葡萄糖的感应性能下降. 结果表明,水热过程中引入的残存水对其电化学性能有很强的影响,微波预处理对其电化学性能也有着重要的影响.     

分级多孔Cafe2O4/C的合成及其微波催化活性

以天然木棉为模板,利用造孔及纳米颗粒自组装两步法合成了分级多孔的Cafe₂O₄/C复合催化剂. Cafe₂O₄/C复合催化剂保留了木棉模板的中空纤维形貌,且该中空纤维是由碳及均匀分布在碳表面的Cafe₂O₄纳米颗粒组成. 该复合催化剂具有较强的甲基紫微波催化降解活性. 研究了Cafe₂O₄负载量、微波功率、催化剂用量、甲基紫的初始浓度和pH值对微波诱导甲基紫降解的影响. 结果表明,Cafe₂O₄/C微波降解甲基紫的催化反应具有较高的反应速率和较短的反应时间. 其降解反应符合一级动力学模型. Cafe₂O₄/C 高的催化活性得益于催化反应和吸附特性之间的协同作用.     

具有介孔结构的MnSiO3@Fe3O4@C纳米粒子的制备以及作为pH响应的T1-T2*双模MRI造影剂的研究应用

本文通过一个简单的、温和的方案制备了平均尺寸为120 nm,介孔结构的纳米粒子MnSiO₃@Fe₃O₄@C. 粒子的细胞毒性微小,可以用作T₁-T₂^*双模MRI造影剂. 酸性条件下MnSiO₃@Fe₃O₄@C释放出大量的Mn²⁺缩短T₁弛豫时间,提高成像分辨率. 超顺磁性的Fe₃O₄可以增强T₂对比成像,检测病变组织. 类似于肿瘤微环境/细胞器的酸性PBS(pH=5.0)中Mn²⁺的释放率达到31.66%,约为中性条件(pH=7.4)下的7倍. 释放的Mn²⁺通过内吞作用被细胞摄取,经肾脏排出,细胞毒性实验表明,MnSiO₃@Fe₃O₄@C具有低的细胞毒性,即使高浓度的200 ppm MnSiO₃@Fe₃O₄@C对HeLa细胞的毒性也相对较小. 对荷瘤小鼠静脉注射定量MnSiO₃@Fe₃O₄@C后,可以观察到一个快速增强的对比成像,给药24 h后,T₁MRI信号显著增强,达到132%,而T₂信号则明显降低至53.8%,活体MR成像证明了MnSiO₃@Fe₃O₄@C可以同时作为阳性和阴性造影剂. 此外,得益于介孔MnSiO₃优秀的酸敏感性,MnSiO₃@Fe₃O₄@C可以作为一种潜在的药物载体,实现肿瘤的诊疗一体化.     

钙钛矿型中温固体氧化物燃料电池阴极Ba0.5Sr0.5Al0.1Fe0.9O3-δ

研究一种新型不含钴的钙钛矿型中温固体氧化物燃料电池阴极Ba_0.5Sr_0.5Al_0.1Fe_0.9O_3-δ (BSAF)材料的晶体结构、电导率以及在对称电池中的电极极化性能. 研究发现,BSAF阴极在空气中低于450 oC表现出典型的具有正温度系数的半导体行为,最高电导率达到14 S/cm;在450-750 oC,却表现出负温度系数,且电导率在750 oC下降到6 S/cm. 电化学研究表明,在基于混合离子导体的对称电池中,BSAF阴极在650-700 oC表现出良好的电极极化性能.以3%H₂O/H₂为燃料和空气为氧化剂,单电池在700 oC的开路电压和最大功率输出分别达到420 mW/cm².     

基于TaCl5的Ta2O2气凝胶制备工艺

 主要介绍了以TaCl₅为前驱体,低分子醇类为溶剂,分别采用环氧丙烷和环氧氯丙烷作为凝胶促进剂制备Ta₂O₂湿凝胶,湿凝胶经过CO₂超临界干燥而获得白色Ta₂O₂气凝胶。透射电镜图谱表明气凝胶是由粒度为10～20 nm的颗粒堆积而成。N₂等温吸附-脱附分析表明,气凝胶的比表面积为800～900 m²/g。     

Mn3O4包覆对LiNi0.5Mn1.5O4正极材料界面电化学性能的提高

本文采用化学湿磨法，首次将金属氧化物Mn₃O₄包覆于LiNi_0.5Mn_1.5O₄颗粒表面，使得电极材料的电子电导率从1.53×10^-7 S/cm 提高到3.15×10^-5 S/cm. 电化学测试结果表明Mn₃O₄包覆大大提高LiNi_0.5Mn_1.5O₄正极材料的倍率性能和高温循环稳定性. 最佳包覆样品为2.6wt% Mn₃O₄包覆的LiNi_0.5Mn_1.5O₄，在10 C倍率下具有108 mAh/g的高放电容并且在55 °C下100次循环后仍有78%的容量保持率，远大于未包覆样品67%的容量保持率.     

海藻酸改性的空心Fe3O4纳米颗粒的制备与应用

不使用任何模板一步制得空心Fe₃O₄纳米颗粒,然后将海藻酸钠嫁接在氨基化的空心Fe₃O₄表面,再利用海藻酸盐与钙离子的作用,在空心Fe₃O₄表面形成一个凝胶化层,制得海藻酸盐凝胶化的空心Fe₃O₄纳米颗粒,粒径约为400～500 nm．采用TEM、XRD、XPS、VSM等手段对纳米微球进行表征．VSM表征结果表明在室温下样品磁性材料为超顺磁性．改性Fe₃O₄纳米颗粒成功地用于柔红霉素的载负和缓释,最大载负率和载药量分别为28.4%和14.2%．缓释结果表明,海藻酸盐凝胶化层的存在,能更有效控制柔红霉素缓慢地释放．     

纯Cr2O3包覆Li4Ti5O12微球的制备及其储锂性能研究

The pure Cr₂O₃ coated Li₄Ti₅O₁₂ microspheres were prepared by a facile and cheap solutionbased method with basic chromium(III) nitrate solution (pH=11.9). And their Li-storage properties were investigated as anode materials for lithium rechargeable batteries. The pure Cr₂O₃ works as an adhesive interface to strengthen the connections between Li₄Ti₅O₁₂ particles, providing more electric conduction channels, and reduce the inter-particle resistance. Moreover, LixCr₂O₃, formed by the lithiation of Cr₂O₃, can further stabilize Li₇Ti₅O₁₂ with high electric conductivity on the surface of particles. While in the acid chromium solution (pH=3.2) modification, besides Cr₂O₃, Li₂CrO₄ and TiO₂ phases were also found in the final product. Li₂CrO₄ is toxic and the presence of TiO₂ is not welcome to improve the electrochemical performance of Li₄Ti₅O₁₂ microspheres. The reversible capacity of 1% Cr₂O₃-coated sample with the basic chromium solution modification was 180 mAh/g at 0.1 C, and 134 mAh/g at 10 C. Moreover, it was even as high as 127 mAh/g at 5 C after 600 cycles. At-20℃, its reversible specific capacity was still as high as 118 mAh/g.     

Nanostructured transition metal oxides for aqueous hybrid electrochemical supercapacitors

In this paper, we wish to present an overview of the research carried out in our laboratories with low-cost transition metal oxides (manganese dioxide, iron oxide and vanadium oxide) as active electrode materials for aqueous electrochemical supercapacitors. More specifically, the paper focuses on the approaches that have been used to increase the capacitance of the metal oxides and the cell voltage of the supercapacitor. It is shown that the cell voltage of an electrochemical supercapacitor can be increased significantly with the use of hybrid systems. The most relevant associations are Fe₃O₄ or activated carbon as the negative electrode and MnO₂ as the positive. The cell voltage of the Fe₃O₄/MnO₂ device is 1.8 V and this value was increased to 2.2 V by using activated carbon instead of Fe₃O₄. These two systems have shown superior behavior compared to a symmetric MnO₂/MnO₂ device which only works within a 1 V potential window in aqueous K₂SO₄. Furthermore, the activated carbon/MnO₂ hybrid device exhibits a real power density of 605 W/kg (maximum power density =19.0 kW/kg) with an energy density of 17.3 Wh/kg. These values compete well with those of standard electrochemical double layer capacitors working in organic electrolytes. PACS 82.47.Uv; 82.45.Fk; 82.45.Yz     

Flexible Ti‐Doped FeOOH Quantum Dots/Graphene/Bacterial Cellulose Anode for High‐Energy Asymmetric Supercapacitors

Ti‐doped FeOOH quantum dots (QD) decorated on graphene (GN) sheets are designed and fabricated by a facile and scalable synthesis route. Importantly, the Ti‐doped FeOOH QD/GN are successfully dispersed within bacterial cellulose (BC) substrate as bending anode with large loading mass for flexible supercapacitor. By virtue of its favorable architecture, this composite electrode exhibits a remarkable areal capacitance of 3322 mF cm^?2 at 2 mA cm^?2, outstanding cycle performance (94.7% capacitance retention after 6000 cycles), and excellent mechanical strength (68.7 MPa). To push the energy density of flexible supercapacitors, the optimized asymmetric supercapacitor using Mn₃O₄/GN/BC as positive electrode and Ti‐doped FeOOH QD/GN/BC as negative electrode can be cycled reversibly in the operating voltage range of 0–1.8 V and displays ultrahigh areal energy density of 0.541 mWh cm^?2, ultrahigh volumetric energy density of 9.02 mWh cm^?3, reasonable cycling performance (9.4% decay in specific capacitance after 5000 cycles), and good capacitive retention at bending state.     

La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO₂/Si衬底上制备出Bi₄Ti₃O₁₂和Bi_3.25La_0.75Ti₃O₁₂薄膜，研究了La掺杂对Bi₄Ti₃O₁₂薄膜的晶体结构、铁电性能和疲劳特性的影响，发现La掺杂没有改变Bi₄Ti₃O₁₂薄膜的基本晶体结构，并且提高了Bi₄Ti₃O₁₂铁电薄膜的剩余极化值和抗疲劳性能，对La掺杂改善Bi₄Ti₃O₁₂铁电薄膜性能的机理进行了讨论. 关键词： 铁电性能 4Ti₃O₁₂薄膜')" href="#">Bi₄Ti₃O₁₂薄膜 3.25La_0.75Ti₃O₁₂薄膜')" href="#">Bi_3.25La_0.75Ti₃O₁₂薄膜 sol-gel法 La掺杂     

Lithium Ferrites@Polydopamine Core–Shell Nanoparticles as a New Robust Negative Electrode for Advanced Asymmetric Supercapacitors

Spinel ferrites hold great promise as attractive electrode materials for high‐performance supercapacitors owing to their multiple valence states and abundant choice of metal cation. However, the main bottleneck for most of the currently reported spinel ferrite‐based electrodes is relatively low specific capacitance. Herein, a new kind of lithium ferrites (Li_0.5Fe_2.5O₄, LFO)@polydopamine (PDA) (denoted as LFO@PDA) core–shell nanoparticles with extraordinary capacitive performance as negative electrodes for aqueous asymmetric supercapacitors (ASCs) are reported first. Taking advantage of increased active sites, improved conductivity, enhanced hydrophilicity, and good strain accommodation in terms of the interesting core–shell architecture and PDA shell, the as‐obtained LFO@PDA electrode reaches a remarkable capacitance of 276.4 F g⁻¹ and prominent durability (no any capacitance loss after 15 000 cycles). Moreover, a robust aqueous 1.8 V‐ASC device with a preferable energy density of 33.9 Wh kg⁻¹ is also achieved based on the LFO@PDA electrode as negative electrode.     

Positive and negative magnetoresistance in Fe3O4-based heterostructures

Fe₃O₄-based heterostructures, including Fe₃O₄/MgO/Fe₃O₄, Fe₃O₄/MgO/Si and Fe₃O₄/SiO₂/Si, were fabricated by magnetron sputtering to investigate the perpendicular-to-plane magneto-transport properties. In the Fe₃O₄/MgO/Fe₃O₄ and Fe₃O₄/MgO/Si heterostructures, the typical magneto-transport properties of single Fe₃O₄ films, such as negative magnetoresistance (MR) and extreme values of MR−T curves at 120 K, were observed, suggesting that the spin polarization of conducting electrons conserves through MgO barrier. MR in the Fe₃O₄/MgO/Fe₃O₄ heterostructure is larger than that in the Fe₃O₄/MgO/Si heterostructure, because the spin of electrons is disturbed in the depletion layer of Si and the SiO₂ layer introduced by Fe₃O₄/MgO growth. The Fe₃O₄/SiO₂/Si heterostructure has a positive MR of 2% at 120 K, which may originate from the scattering of conducting electrons in amorphous SiO₂ and the spin polarization reversal at the Fe₃O₄/SiO₂ interface.     

Cocktail effect of Fe2O3 and TiO2 semiconductors for a high performance dye-sensitized solar cell

The bi-semiconductors of TiO₂ and Fe₂O₃ were used as a photoelectrode material in a high performance dye-sensitized solar cell due to cocktail effects from the two conduction bands. The size of the semiconductors was reduced by using a paint shaker to enlarge the contact area of the semiconductor with the dye or electrolyte. The fill factor and the efficiency of the prepared dye-sensitized solar cell were improved by over 16% and 300%, respectively; these parameters were measured from a current-voltage curve that was based on the effects of the Fe₂O₃ co-semiconductor and the size reduction. A mechanism is suggested wherein the conduction band of Fe₂O₃ works to prohibit the trapping effects of electrons in the conduction band of TiO₂. This result is attributed to the prevention of electron recombination between electrons in the TiO₂ conduction band with dye or electrolytes. The mechanism is suggested based on impedance results, which indicate improved electron transport at the interface of the TiO₂/dye/electrolyte.     

Spinel lithium titanate (Li4Ti5O12) as novel anode material for room-temperature sodium-ion battery

This is the first time that a novel anode material, spinel Li₄Ti₅O₁₂ which is well known as a “zero-strain” anode material for lithium storage, has been introduced for sodium-ion battery. The Li₄Ti₅O₁₂ shows an average Na storage voltage of about 1.0 V and a reversible capacity of about 145 mAh/g, thereby making it a promising anode for sodium-ion battery. E_x-situ X-ray diffraction (XRD) is used to investigate the structure change in the Na insertion/deinsertion process. Based on this, a possible Na storage mechanism is proposed.     

调控氧空位实现高比表面积Co3O4纳米片上的产氧反应

Electrochemical water splitting requires efficient water oxidation catalysts to accelerate the sluggish kinetics of water oxidation reaction. Here, we designed an efficient Co₃O₄ electrocatalyst using a pyrolysis strategy for oxygen evolution reaction (OER). Morphological characterization confirmed the ultra-thin structure of nanosheet. Further, the existence of oxygen vacancies was obviously evidenced by the X-ray photoelectron spectroscopy and electron spin resonance spectroscopy. The increased surface area of Co₃O₄ ensures more exposed sites, whereas generated oxygen vacancies on Co₃O₄ surface create more active defects. The two scenarios were beneficial for accelerating the OER across the interface between the anode and electrolyte. As expected, the optimized Co₃O₄ nanosheets can catalyze the OER efficiently with a low overpotential of 310 mV at current density of 10 mA/cm² and remarkable long-term stability in 1.0 mol/L KOH.     

Preparation and magnetic properties of BaFe12O19/Ni0.8Zn0.2Fe2O4 nanocomposite ferrite

Nanocomposite of hard (BaFe₁₂O₁₉)/soft ferrite (Ni_0.8Zn_0.2Fe₂O₄) have been prepared by the sol–gel process. The nanocomposite ferrite are formed when the calcining temperature is above 800 °C. It is found that the magnetic properties strongly depend on the presintering treatment and calcining temperature. The “bee waist” type hysteresis loops for samples disappear when the presintering temperature is 400 °C and the calcination temperature reaches 1100 °C owing to the exchange-coupling interaction. The remanence of BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite with the mass ratio of 5:1 is higher than a single phase ferrite. The specific saturation magnetization, remanence magnetization and coercivity are 63 emu/g, 36 emu/g and 2750 G, respectively. The exchange-coupling interaction in the BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite is discussed.     

硅纳米孔柱阵列及其四氧化三铁复合薄膜的湿敏电容特性研究

报道了硅纳米孔柱阵列（Si-NPA），Fe₃O₄复合的Si-NPA（Fe ₃O₄/Si-NPA）两种薄 膜材料的制备方法并对其形貌和结构进行了表征，研究了其电容湿度传感特性.结果表明，S i-NPA，Fe₃O₄/Si-NPA均为微米/纳米结构复合体系.当环境相对湿 度从11％上升到95％ 时，采用100 Hz的信号频率进行测试，以Si-NPA和Fe₃O₄/Si-NPA 为电介质材料制成的湿 敏元件的电容增加值分别为起始值的1500％和5500％；采用1000 Hz的信号频率测试时，则 分别为起始值的800％和12000％，显示出两种材料较高的湿度灵敏性和较强的绝对电容输出 信号强度.同时，在升湿和降湿过程中，Si-NPA，Fe₃O₄/Si-NPA都 具有较快的响应速度 ，其响应时间分别为15 s，5 s和20 s，15 s.文章结合材料的形貌和结构特性对其物理机理 进行了分析.上述结果表明，Si-NPA无论是直接作为湿度薄膜传感材料还是作为复合薄膜湿 度传感材料的衬底都具有很好的前景. 关键词： 硅纳米孔柱阵列 3O₄')" href="#">Fe₃O₄ 湿度电容传感特性