掺铒光纤中方波信号高次谐波的快慢光特性

光纤中方波信号的慢光技术在全光通信和光纤传感等领域具有重要的应用前景. 提出了谐波相对延时量的度量方法, 分别采用速率方程和相干布居振荡理论, 对掺铒光纤中方波信号的基波和高次谐波的快慢光特性进行了研究. 在无抽运光输入情况下, 改变入射光功率, 入射探测光的基波最大相对延时量能达到20%, 且存在实现最大相对延时量的入射光功率为8 mW; 在有抽运光输入的情况下, 改变信号光增益, 入射探测光的基波相对超前量同样能达到-20%, 且随着信号光增益的增大而增加. N次谐波(N=1, 3, 5, 7, …)在频率f/N(f为基波信号最大延时量对应的调制频率)处有最大相对延时量, 且它们的最大延时量相同, 频率处于相干布居振荡引起的光谱烧孔带宽内.     

光纤中基于双宽带抽运的受激布里渊散射增益谱展宽及慢光传输中脉冲失真减小的理论研究

分析了单模光纤中双宽带抽运的受激布里渊散射 （stimulated Brillouin scattering,SBS） 光速减慢效应.模拟了两高斯型宽带抽运光同时作用下的SBS增益谱和损耗谱,提出了一种获得均匀增益谱的方法.由于较强抽运光增益谱的中心频率与较弱抽运光损耗谱的中心频率相重合,通过调节较弱抽运光的功率和谱宽,能够部分地抵消掉较强增益谱的顶部从而构建出平坦的增益谱.研究了该平顶增益情形下信号脉冲畸变的性质.与单宽带抽运下脉冲畸变的对比表明,这种产生平顶增益谱的方法能有效地减小脉冲畸变. 关键词： 慢光 受激布里渊散射（SBS） 单模光纤 脉冲失真     

信号光的调制对基于光纤光参量放大光脉冲源的改善

在理论上从四波混频的强度耦合方程出发,给出了基于光纤光参量放大(FOPA)光脉冲的光场表达式,并进一步分析了信号光被相位调制或强度调制后,光脉冲的频率啁啾和强度演化.结论指出：若信号光被强度调制,对所生成脉冲宽度无明显的影响,但可以提高消光比;若信号光被相位调制,所生成的脉冲具有更大的线性正啁啾,可以在相同的抽运功率条件下得到比无相位调制时更窄的脉冲.实验上给出了10 GHz工作速率下的结果,其结果与理论分析符合得很好.通过信号光的相位调制,在05 W平均抽运功率条件下得到了消光比22 dB,脉宽为5 关键词： 光纤参量放大 四波混频 光脉冲源 频率啁啾     

矩形谱宽带光抽运的布里渊慢光理论研究

对矩形谱宽带光抽运下的布里渊慢光延迟特性进行了理论分析。在小信号增益情况下,得到了高斯脉冲延时量、脉冲展宽因子和增益的解析表达式。计算结果表明,当信号光的10 dB带宽小于抽运光带宽的0.357时,解析解和数值解吻合,且信号光脉冲能实现零展宽延迟。单个矩形谱宽带光抽运能达到的最大有效布里渊增益带宽为20 GHz,可以实现半峰全宽约100 ps的高斯光脉冲的零展宽延迟。与高斯谱宽带抽运光相比,矩形谱宽带抽运光可减小脉冲失真。     

矩形谱宽带光抽运的布里渊慢光中脉冲失真的分析

在小信号增益条件下推导出了高斯光脉冲经过矩形谱宽带光抽运的布里渊慢光系统后输出脉冲时域振幅包络的近似解析表达式,适用于抽运光频谱具有陡峭上升(下降)沿和平坦顶部的情况.定量分析和比较了光纤色散以及受激布里渊散射增益不均衡和增益所致色散效应对延迟信号光脉冲失真的影响.计算结果表明:当信号光脉冲的频谱处于布里渊有效增益谱内时,解析解与数值解符合,布里渊增益所致三阶色散效应是导致延迟信号光脉冲失真的主要物理因素,制约了窄脉冲延迟量的提高.     

饱和放大情形下光纤参量放大器的增益和带宽特性研究

利用龙格库塔法数值求解非线性耦合方程,研究了单抽运光纤参量放大器在增益饱和区的增益谱特性.通过比较考虑抽运光损耗与忽略抽运光损耗增益谱的差别,分析了抽运光损耗对增益谱的影响.此外,给出了在饱和放大区,信号光的增益谱与光纤长度、输入信号光功率、抽运光波长与零色散波长偏离之间的关系.发现在饱和放大区,增益的整体水平有所下降,增益谱的可用带宽相对于小信号放大有所减少,增益谱在可用带宽范围内出现了旁瓣.这些结果将对工作在饱和放大区的单抽运光参量放大器的设计提供有益的帮助.     

双向抽运拉曼光纤放大器性能的研究

对双向抽运拉曼光纤放大器(RFA)的噪声特性、增益饱和及抽运功率转换效率进行了详细研究。结果表明,双向抽运拉曼光纤放大器的噪声特性介于前向抽运与后向抽运之间,但主要取决于前向抽运方式所导致的噪声特性;双向抽运方式的饱和功率低于单向抽运方式的饱和功率,同前向抽运与后向抽运提供的增益比例有关;双向抽运方式的抽运功率转换效率同信号光功率及前、后向抽运提供的增益有关,当信号光功率较低时,增加前向抽运的比例可取得较高的抽运功率转换效率,而信号光功率较高时,增加后向抽运的比例可取得较高的抽运功率转换效率。研究一种配置(情况3)的双向抽运拉曼光纤放大器,可以完全补偿100km传输线路的损耗(包括无源器件的损耗),最低光信噪比为30．21dB。     

单频光纤拉曼放大器的实验研究

本文进行了1031 nm抽运光对1080 nm单频信号光的拉曼放大实验,详细研究了单频信号光种子功率、拉曼增益光纤长度、抽运方式等因素对 单频光纤拉曼放大器(SF-FRA)输出特性的影响.结果表明,在未受受激布里渊散射(SBS)因素限制时,相同抽运功率条件下,单频信号光种子功率越高,SF-FRA的效率越高;拉曼增益光纤越长,SF-FRA的效率越高;前向抽运时,SF-FRA的效率较高.实验中发现SF-FRA的拉曼放大过程对单频信号光的线宽有较小的展宽.此外,单频信号光远场干涉短曝光图像的对比度为0.814,单频信号光与SF-FRA放大光远场干涉短曝光图像可见度为0.719,表明SF-FRA对单频信号光的相干性有一定影响.实验结论可为其他特殊波长SF-FRA的设计提供一定的参考.     

掺镱光纤激光器自脉冲与自脉冲内的自锁模研究

采用单端连续抽运方式, 对自由运转的双包层掺镱光纤激光器的输出特性进行了详细的实验研究. 实验中不但观察到了自脉冲, 而且首次在自由运转的光纤激光器中观察到自锁模现象, 对它们产生的物理机理进行了相应的理论分析. 分析表明: 增益光纤的弱(未) 抽运部分对信号光的吸收导致光纤激光器内自脉冲的出现, 轴向模之间的拍频和自相位调制导致自锁模现象的出现, 而受激拉曼散射、 受激布里渊散射等非线性效应使它们进一步增强. 当抽运光功率略高于阈值时, 自脉冲宽度比较宽, 随抽运光功率增加自脉冲的脉宽变窄; 自脉冲包络面内的自锁模脉冲的宽度随抽运光功率增加也变窄, 进一步增加抽运光功率, 自脉冲和自脉冲包络面内的自锁模现象消失. 实验测得自锁模脉冲的间隔为224 ns, 最大(小) 自锁模脉冲的半高全宽约为35.0 ns (6.3 ns); 测得信号光的中心波长为1090 nm, 谱线半高全宽的最大(小) 值约为7.05 nm (2.01 nm).     

高功率光子晶体光纤放大器实验研究

利用掺Yb³⁺的光子晶体光纤作为光纤放大器的增益介质,采用反向抽运方式,分别从理论和实验方面研究了不同信号的增益特性,在信号光功率为6W,抽运光功率为160W时,获得了104W的输出功率.实验发现,当抽运功率大于一定值时,放大器输出会有一定的不稳定性,并影响输出功率的进一步提高. 关键词： 光子晶体光纤 光纤放大器 反向抽运 高功率     

Tunable slow and fast light with large bandwidth in the band-edge of gain spectrum of the wide band fiber optical parametric amplifier

We propose a novel method theoretically to generate the slow and fast light with large bandwidth and low gains, which is based on the parametric process in fiber. In our scheme, the wide band fiber optical parametric amplifier is employed and the whole signal bandwidth should be located at a certain frequency range of the band-edge of gain spectrum, and then signal waves will be delayed or advanced with low signal gains because of the peculiar feature of signal gain and phase shift. By changing the pump power, the delay time is continuously-tunable optically. The ultimate delay bandwidth and the delay bandwidth product are constrained by the shape of time delay spectrum. Our simulation verifies that 22.4 ps delay or advanced time for the bandwidth of 10 GHz with little distortion can be obtained at certain wavelengths in the optical communication waveband, and their gains are nearly zero. The tunable range is from 0 ps to 22.4 ps for the signal bandwidth of 10 GHz, and it is from 0 ps to 15.6 ps for the bandwidth of 15 GHz. This type of slow and fast light in wide band FOPA has the potential capability to produce the tunable slow and fast light for large bandwidth with low signal gains in future.     

Flat and ultra-broadband two-pump fiber optical parametric amplifiers based on photonic crystal fibers

A two-pump fiber optical parametric amplifier (FOPA) based on the photonic crystal fiber (PCF) in the telecommunication region is investigated numerically. The fiber loss and pump depletion are considered. The influences of the fiber length, input signal power, input pump power, and the center pump wavelength on the gain bandwidth, flatness, and peak gain are discussed. The 6-wave model-based analysis of two-pump FOPA is also achieved and compared with that based on the 4-wave model; furthermore, the gain properties of the FOPA based on the 6-wave model are optimized and investigated. The comparison results show that the PCF-based two-pump FOPA achieves flatter and wider gain spectra with less fiber length and input pump power compared to the two-pump FOPA based on the normal highly nonlinear fiber, where the obtained results show the great potential of the FOPA for the optical communication system.     

Optimized design of two-pump fiber optical parametric amplifier and its noise characteristics

In the paper, based on the pump depleted model of two-pump fiber optical parametric amplifier (FOPA), the simulations are done to indicate the effect of amplifier parameters on gain characteristics, such as the input signal power, the wavelength separation between the two pumps, the fiber length, the nonlinear coefficient and the fourth-order dispersion of fiber. By optimizing the amplifier parameters, when FOPA attains low gain-saturation, the FOPA has a higher gain, a broader flat gain bandwidth and a lower noise figure. However, with the enhancement of gain-saturation the parametric gain decreases, the flat gain bandwidth becomes narrow and the noise figure also increases.     

Slow and fast light based on SBS with the spectrum tailoring

In this paper, slow and fast light of a signal pulse of nanosecond duration are achieved in the same experimental device by using band-pass filters to tailor the spectra of spontaneous Brillouin scattering (SPBS) coming from 50 km single-mode optical fibers (SMF) as the pump light. The phase matching condition of slow and fast light is satisfied by changing wavelengths of band-pass filters .In our experiment, we obtain the tunable delay time for various signal pulses range from 1 ns to 20 ns. By increasing the power of the pump field to 16 mW, a 1 ns signal pulse is delayed 1.5 ns and is advanced 1.0 ns respectively, while the signal pulse almost has no distortion. The experiment has demonstrated that larger relative pulse delay of slow and fast light can be obtained in the same experimental setup when pump power is lower.     

光电延迟反馈系统几种混沌路径的仿真分析

对非线性光电延迟反馈系统的响应时间序列进行数值分析.模型反馈循环中加入带通滤波器,建立非线性光电延迟反馈系统的数学模型.用龙格-库塔数值分析方法,通过调节参数,发现两种产生混沌信号的路径.设置特定φ时,在低反馈增益情况下,系统输出快速方波信号或慢速周期震荡信号,随着反馈增益的增加,系统输出出现复杂周期信号或混沌breather现象;在高反馈增益时,系统输出从不同的动力特性变成混沌状态.     

基于一种优化的梳状布里渊增益谱实现对任意周期信号的零展宽快慢光

在理论分析任意信号实现无畸变快慢光所需条件的基础上,根据周期信号的频谱特点,推导出一种优化的梳状布里渊增益谱的普适公式.利用该普适公式,可根据所需时间延迟或超前量,方便地得到周期信号每个离散频谱分量所对应的各离散布里渊增益谱的强度和增益谱峰值相对于频谱分量的偏移量,从而确定整个梳状布里渊增益谱的形状.通过对正弦信号、周期性高斯信号和周期性方波信号的数值计算,结果表明,利用该优化的梳状布里渊增益谱可实现这三种周期信号在零展宽下的快慢光,证实了所得普适公式的正确性.此外,通过调节各离散布里渊增益谱的强度和偏移量,时间延迟或超前量连续可调.     

Gain characteristics and optimization of dual-pump fiber optical parametric amplifier using two-section highly nonlinear fibers

In this paper the gain characteristics of two-pump fiber optical parametric amplifiers (FOPA) with two-section highly nonlinear fibers are analyzed numerically and the parameters of the fibers are optimized to reach broad and flat gain spectra using genetic algorithm. Different from the previous methods, here the space between two pump wavelengths and the parameter β₄ of the fibers are included as a pivotal factor in the optimization. The numerical simulation shows that using two-section practical high nonlinear fibers, the amplifier may reach 110 nm bandwidth covering 1495–1605 nm with 10.5 dB average gain and gain ripple of 0.17 dB, when the total pump power is 1 W.     

High efficiency and high output power fiber-optic parametric amplifier

A highly efficient fiber-optic parametric amplifier (FOPA) is presented. A nearly complete pump depletion of 99.92% in a single-pumped FOPA is experimentally demonstrated with a pump power of 1W. In addition, a high signal output power of 0.53W is presented, corresponding to a power conversion efficiency of 53%, which is believed to be the highest efficiency ever reported for an FOPA.     

Numerical modelling of the pump-to-signal relative intensity noise transfer in two-pump fibre optical parametric amplifiers

An accurate numerical model to investigate the pump-to-signal relative intensity noise (RIN) transfer in two-pump fibre optical parametric amplifiers (2-P FOPAs) for low modulation frequencies is presented. Compared to other models in the field, this model takes into account the fibre loss, pump depletion as well as the gain saturation. As a result, the model allows to include a wide range of practical circumstances, both in and beyond the undepleted pump regime, related to different applications of FOPAs. In the small-signal or undepleted pump regime, the model predicts the ripples of the RIN spectrum very well and yields better results than those of other models. It is shown that beyond the small-signal regime, pump power variations do not remain unchanged over the length of the amplifier and for high signal powers, when the FOPA saturates, minimum pump-to-signal RIN transfer occurs. The results of the model are also compared with the available experimental data in the field and a very good agreement can be seen.